Viglen Vig566s User manual

Vig560s Motherboard Manual

01-02-2005

C O M P U T E R S N E T W O R K S S O L U T I O N S

..

Vig560s

Motherboard

Manual

Vig560s Motherboard Manual

1

Viglen, EMC and the ‘CE’ mark

CE Marking

European standards are being harmonised across borders. If products comply with the same

standards in all European countries, product exporting and importing is made simple - paving our way

to a common market. If you buy a product with a 'CE' mark on it (shown below), on the box, in the

manual, or on the guarantee - it complies with the currently enforced directive(s).

Introduction to EMC

EMC (Electromagnetic Compatibility) is the term used to describe certain issues with RF (Radio

Frequency) energy. Electrical items should be designed so they do not interfere with each other

through RF emissions. E.g. If you turn on your microwave, your television shouldn't display

interference if both items are CE marked to the EMC directive.

If emitted RF energy is not kept low, it can interfere with other electrical circuitry - E.g. Cars Automatic

Braking Systems have been known to activate by themselves while in a strong RF field. As this has

obvious repercussions ALL electrical products likely to cause RF related problems have to be 'CE'

marked from 1st January 1996 onwards.

If a product conforms to the EMC directive, not only should its RF emissions be very low, but its

immunity to RF energy (and other types) should be high. The apparatus has to resist many 'real

world' phenomena such as static shocks and mains voltage transients.

Viglen’s Environment laboratory

To gain a 'CE' mark, the Viglen computer range has had to undergo many difficult tests to ensure it is

Electromagnetically Compatible. These are carried out in the in-house 'Environment lab' at Viglen

Headquarters. We have made every effort to guarantee that each computer leaving our factory

complies fully with the correct standards. To ensure the computer system maintains compliance

throughout its functional life, it is essential you follow these guidelines.

¾ Install the system according to Viglen’s instructions

¾ If you open up your Viglen:

¾ Keep internal cabling in place as supplied.

¾ Ensure the lid is tightly secured afterwards

¾ Do not remove drive bay shields unless installing a 'CE' marked peripheral in its place

¾ The clips or ‘bumps' around the lips of the case increase conductivity - do not remove or

damage.

¾ Do not remove the ferrite ring from the L.E.D cables.

¾ Only use your Viglen computer with 'CE' marked peripherals

This system has been tested in accordance with European standards for use in residential and light

industrial areas-this specifies a 10 meter testing radius for emissions and immunity. If you do

experience any adverse affects which you think might be related to your computer, try moving it at

least 10 meters away from the affected item. If you still experience problems, contact Viglen’s

Technical Support department who will put you straight through to an EMC engineer - s/he will do

everything possible to help. If modifications are made to your Viglen computer system, it might breach

EMC regulations. Viglen take no responsibility (with regards to EMC characteristics) of equipment

which has been tampered with or modified.

Vig560s Motherboard Manual

2

Copyrights and Trademarks

Please note

The material in this manual is subject to change without notice.

Trademarks

Microsoft, Windows, Windows NT, Windows 95,Windows 98, Windows ME,

Windows 2000 Pro, Windows XP Pro and MS-DOS are registered trademarks of

Microsoft Corporation. IBM PC, XT, AT and PS/2 are trademarks of International

Business Machines Corporation. Pentium and Pentium Pro are registered

trademarks of Intel Corporation. AMI BIOS is a registered trademark of American

Megatrends. All other trademarks are acknowledged. JAC-UP, Genie, Contender,

Dossier, Vig, Viglen, and Envy are trademarks of Viglen Limited.

Copyright and Patents

This manual and all accompanying software and documentation are copyrighted and

whole or in part, be copied, photocopied, translated or reduced to any electronic or

machine-readable form, without prior written consent except for copies retained by

the purchaser for backup.

VIG560S Manual Version 1.0

Printed in the United Kingdom

Liability

No warranty or representation, either expressed or implied, is made with respect to

this documentation, its quality, performance, merchantability or fitness for a particular

purpose. As a result the documentation is licensed as is, and you, the licensee, are

assuming the entire risk as to its quality and performance. The vendor reserves the

right to revise this operation manual and all accompanying software and

documentation and to make changes in the content without obligation to notify any

person or organisation of the revision or change.

In no event will the vendor be liable for direct, indirect, special, incidental or

consequential damages arising out of the use or inability to use this product or

documentation, even if advised of the possibility of such damages. In particular, the

vendor shall not have liability for any hardware, software or data stored or used with

the product, including the costs of repairing, replacing or recovering such hardware,

software or data.

Vig560s Motherboard Manual

3

Contents

Chapter 1: Motherboard Overview 5

Feature Summary 6

Motherboard Special Features 8

Additional BIOS Features 9

Onboard LED Support 10

System Board Components 11

Back Panel Connectors 15

Chapter 2: System Board Options 18

Overview of Jumper Settings 20

Motherboard Jumper Settings 21

Motherboard Connectors 23

Central Processing Unit (CPU) 31

System Memory 36

Expansion Slots (PCI & PCI-Express) 40

Replacing the Clock/CMOS RAM Battery 42

Chapter 3: Solving Problems 43

Resetting the System 43

Troubleshooting Procedures 44

Problems Operating Add-in Boards 45

Problems & Suggestions 46

Chapter 4: System BIOS 48

What is the BIOS? 48

The Power-On Sequence 48

Managing and Updating your BIOS 49

AFUDOS Utility 49

BIOS Setup Program 51

BIOS Menu Screen 53

BIOS Main Menu 56

Primary, Third and Fourth IDE Master/Slave Sub-menu 56

IDE Configuration Sub-menu 58

Vig560s Motherboard Manual

4

System Information Sub-menu 59

BIOS Advanced Menu 60

USB Configuration Sub-menu 60

CPU Configuration Sub-menu 61

Chipset Sub-menu 63

Onboard Devices Configuration Sub-menu 65

PCI PnP Sub-menu 66

BIOS Power Menu 68

APM Configuration Sub-menu 69

Hardware Monitoring Sub-menu 71

BIOS Boot Menu 72

Boot Device Priority Sub-menu 73

Boot Settings Configuration Sub-menu 73

Security Sub-menu 74

BIOS Exit Menu 77

Chapter 5: Glossary 79

Notes 83

Chapter 7: Suggestions 84

Vig560s Motherboard Manual

5

Chapter 1: Motherboard Overview

Introduction

This manual describes the Viglen VIG560S motherboard inside your computer. The

motherboard is the most important part of your computer. It contains all of the CPU,

memory and graphics circuitry that make the computer work.

The motherboard contains the very latest CPU design, the Intel Pentium 4™

processor, which includes Intel NetBurst® Microarchitecture with 800 MHz system

bus, Internet Streaming SIMD Extensions, Intel Hyper-Threading Technology

hardware support for multi-threaded applications and Intel’s Extended Memory 64-bit

technology (EM64T). All of which are designed to vastly improve both multimedia

and communications on your PC. The combination of this technology and Viglen

expertise make this a formidable computer.

The motherboard contains the very latest CPU design that supports the Intel®

Pentium® 4 family including Hyper-Threading enabled CPU’s and the very latest

Extreme Edition CPU’s. All of the supported CPU’s include Intel’s® MMX

Technology. MMX technology adds a total of 57 new instructions to the CPU, all of

which are designed to vastly improve both multimedia and communications on your

PC. The combination of the Intel® processor, MMX technology and Viglen expertise

make this a formidable computer.

This manual contains technical information about the Viglen VIG560S motherboard

and other hardware components inside your computer. If you are new to computers

we recommend that you read the user guide first. If you are an experienced

computer user this manual should provide all the information you will need to

perform simple upgrades and maintenance.

We hope that this manual is both readable and informative. If you have any

comments for suggestions about how we could improve the format then please fill

out the form at the back of the manual and send it to us.

Above all we hope that you enjoy using your Viglen computer.

Vig560s Motherboard Manual

6

Feature Summary

The Vig560s motherboard supports Intel® Pentium® 4 and Celeron® processors

with up to 1MB of second-level cache integrated in a LGA775 Socket package

operating at speeds up to 3.8GHz.

The motherboard features:

Form factor:

• Micro ATX form factor: 9.6 in x 9.6 in (24.5 cm x 24.4 cm)

CPU Support:

• LGA775 socket for Intel® Pentium® 4/Celeron processor

• Compatible with Intel® PCG 04A and 04B processors

• Supports Intel® Hyper-Threading Technology

Chipset Support:

• Northbridge: Intel® 915G Graphics Memory Controller Hub (GMCH)

• Southbridge: Intel® ICH6

Front Side Bus (FSB):

• 800/533 MHz

Memory Support:

• Dual-channel memory architecture

• 4 x 184-pin DIMM sockets support unbufferred non-ECC

• 400/333 MHz DDR memory modules

Graphics Support:

• Integrated Intel® Graphics Media Accelerator 900

Expansion Support:

• 1 x PCI Express x16 slot for discrete graphics card

• 1 x PCI Express x1 slot

• 2 x PCI slots

Storage Support:

• Intel® ICH6 Southbridge supports:

o 1 x Single-channel Ultra DMA 100/66/33

Vig560s Motherboard Manual

7

o 4 x Serial ATA

High Definition Audio Support:

• Realtek® ALC861 8-channel CODEC

• S/PDIF out interface support

LAN Support:

• Intel® Pro1000VE PCI Gigabit Ethernet LAN controller

USB Support:

• Supports up to 8 USB 2.0 ports

BIOS Features:

• 4 MB Flash ROM, AMI BIOS, PnP, DMI2.0, SM BIOS 2.3, WfM2.0

Rear Panel Port Support:

• 1 x PS/2 mouse port

• 1 x Parallel port

• 1 x LAN (RJ-45) port

• 8-channel audio ports

• 4 x USB 2.0 ports

• 1 x VGA port

• 1 x Serial port

• 1 x PS/2 keyboard port

Internal Connectors:

• 1 x Floppy disk drive connector

• 1 x Primary IDE connector

• 1 x PCI IDE connector

• 4 x Serial ATA connectors

• 1 x CPU fan connector

• 1 x Chassis fan connector

• 2 x USB 2.0 connectors

• 1 x 24-pin ATX power connector

• 1 x 4-pin ATX 12 V power connector

• 1 x Optical drive audio connector

• 1 x Front panel High Definition Audio connector

• 1 x Chassis intrusion connector

• 1 x Speaker Out connector

• 1 x Digital audio connector

• 1 x System panel connector

Vig560s Motherboard Manual

8

Power Requirements:

• ATX power supply (with 24-pin and 4-pin 12 V plugs)

• ATX 12 V 2.0 compliant

Motherboard Special Features

Latest Processor Technology

The motherboard comes with a 775-pin surface mount Land Grid Array (LGA) socket

designed for the Intel® Pentium® 4 processor in the 775-land package. The

motherboard supports the Intel® Pentium® 4 processor with 533 and 800 MHz Front

Side Bus (FSB). The motherboard also supports the Intel® Hyper-Threading

Technology and is fully compatible with Intel® 04B and 04A processors.

Intel 915G

The Intel® 915G graphics memory controller hub (GMCH) and the ICH6 I/O

controller hub provide the vital interfaces for the motherboard. The GMCH features

the Intel® Graphics Media Accelerator 900, an integrated graphics engine for

enhanced 3D, 2D, and video capabilities. The GMCH provides the interface for a

processor in the 775-land package with 533/800 MHz front side bus (FSB), dual

channel DDR at speeds of up to 400 MHz, and PCI Express x16 interface for a

graphics card.

The Intel® ICH6 Southbridge represents the sixth generation I/O controller hub that

provides the interface for PCI Express and 8-channel high definition audio.

Dual Channel DDR Memory Support

Employing the Double Data Rate (DDR) memory technology, the motherboard

supports up to 4 GB of system memory using DDR 400/333 DIMMs. The ultra-fast

400 MHz memory bus delivers the required bandwidth for the latest 3D graphics,

multimedia, and Internet applications.

PCI Express Interface

The motherboard fully supports PCI Express, the latest I/O interconnect technology

that speeds up the PCI bus. PCI Express features point-to-point serial

interconnections between devices and allows higher clock speeds by carrying data in

packets. This high speed interface is software compatible with existing PCI

specifications.

Vig560s Motherboard Manual

9

Serial ATA Technology

The motherboard supports the Serial ATA technology through the Serial ATA

interfaces and the Intel® ICH6. The SATA specification allows for thinner, more

flexible cables with lower pin count, reduced voltage requirement, and up to 150

MB/s data transfer rate.

8-Channel High Definition Audio

Onboard is the Realtek® ALC861 7.1-channel audio CODEC. This CODEC is fully-

compliant with Intel® High Definition Audio standard (192 KHz, 24-bit audio). With

the CODEC, 8-channel audio ports, and S/PDIF interfaces, you can connect your

computer to home theatre decoders to produce crystal-clear digital audio.

S/PDIF Digital Sound Ready

The motherboard supports the S/PDIF Out function through the S/PDIF interface at

mid board. The S/PDIF technology turns your computer into a high-end

entertainment system with digital connectivity to powerful audio and speaker

systems.

USB 2.0 Technology

The motherboard implements the Universal Serial Bus (USB) 2.0 specification,

dramatically increasing the connection speed from the 12 Mbps bandwidth on USB

1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.

Additional BIOS Features:

Crash Free BIOS 2

This feature allows you to restore the original BIOS data from the support CD in case

when the BIOS codes and data are corrupted. This protection eliminates the need to

buy a replacement ROM chip.

Q-Fan Technology

The ASUS Q-Fan technology smartly adjusts the fan speeds according to the system

loading to ensure quiet, cool, and efficient operation.

EZ Flash BIOS

With the ASUS EZ Flash, you can easily update the system BIOS even before

loading the operating system. No need to use a DOS-based utility or boot from a

floppy disk.

Vig560s Motherboard Manual

10

MyLogo

This feature allows you to personalise and add style to your system with

customisable boot logos.

Onboard LED Support

The motherboard comes with a standby power LED that lights up to indicate that the

system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should

shut down the system and unplug the power cable before removing or plugging in

any motherboard component. The illustration below shows the location of the

onboard LED.

Figure 1: Motherboard LED

Vig560s Motherboard Manual

11

System Board Components

Figure 2: Motherboard Layout & Components

Table 1: Motherboard Connections

A: Front Panel Audio Connector O: Parallel IDE (P-ATA) connector

B: Realtek ALC861 audio codec P: Power connector (24 way ATX2.2)

C: Aux/CD internal audio connector Q: Intel® 82801FB I/O Controller Hub (ICH6)

D: PCI Conventional bus add-in card connectors R: Serial ATA (S-ATA) connectors

E: Intel Pro1000VE PCI Gigabit Ethernet Controller S: Front panel connector

F: PCI Express x16 bus add-in card connector T: 4 Mbit Firmware Hub (FWH)

G: Back panel connectors U: Front panel USB connectors

H: +12V power connector (ATX12V) V: Front panel USB connectors

I: LGA775 processor socket (Socket T) W: Battery

J: Rear chassis fan connector X: ITE 8211 controller (not fitted)

K: Processor fan connector Y: Power to motherboard LED

L: DIMM Channel A & B Sockets Z: Intel® 82915G Graphics Memory

Controller Hub (GMCH)

M: I/O controller AA: PCI Express x1 bus add-in card

N: Floppy drive connector BB: SPIDIF_OUT (not fitted)

Vig560s Motherboard Manual

12

Overview of System Board Components

A – Front Panel Audio Connector

This connector allows for the use of front facing audio in a desktop chassis. The

connector allows the signal to be passed through from the rear connector to the front

connector.

B – Realtek ALC861 audio codec

Decodes different audio formats.

C – Aux/CD internal audio connector

Allows the audio from the CD-ROM to be run though the internal audio via an

analogue cable.

D – PCI Conventional bus add-in card connectors

Allows a PCI device to be fitted such as a fire wire card or wireless card.

E – Intel Pro1000VE PCI Gigabit Ethernet Controller

Onboard LAN controller.

F – PCI Express x16 bus add-in card connector

Allows a PCI Express x16 device to be fitted to the motherboard. E.g. Graphics card

G – Back panel connectors

The ports on the back panel include: PS/2, Parallel, Serial, VGA, 4 x USB, RJ45 and

6 x 3.5mm audio jack sockets.

H – +12V power connector (ATX12V)

Provides additional power to the processor.

I – LGA775 processor socket (Socket T)

This is the socket in which the processor is installed into.

J – Rear chassis fan connector

Rear chassis fan connector. This fan header is thermally managed by Q-Fan

technology.

Vig560s Motherboard Manual

13

K – Processor fan connector

Allows for the processor fan to be connected. The fan header is PWM compliant.

L – DIMM Channel A & B Sockets

This allows up to 4GB of DDR RAM to be installed. Up to 1GB of RAM in each slot.

M – I/O controller

Handles all the input/output signals to and from the motherboard.

N – Floppy drive connector

This allows a floppy drive to be added to the motherboard. The port is slotted to

ensure correct installation.

O – Parallel IDE (P-ATA) connector

This allows up to 2 devices, such as CD/DVD drives and hard drives to be added

to the IDE channel. The port is slotted to ensure correct installation.

P – Power connector (24 way ATX2.2)

This is the main power connector.

Q – Intel® 82801FB I/O Controller Hub (ICH6)

The Intel® ICH6 Southbridge represents the sixth generation I/O controller hub that

provides the interface for PCI Express and 8-channel high definition audio.

R – Serial ATA (S-ATA) connectors

This allows for up to 4 devices. One device can be installed on one S-ATA connector

on the motherboard running at 150MB/s.

S – Front panel connector

This is the panel to which the case cables are connected, such as the power switch.

Power LED etc.

T – 4 Mbit Firmware Hub (FWH)

This is an optional feature which is not offered by Viglen.

U – Front panel USB connectors

This allows an additional 2 USB ports to be added with the use of a cable.

Vig560s Motherboard Manual

14

V – Front panel USB connectors

This allows an additional 2 USB ports to be added with the use of a cable.

W – Battery

The battery keeps the CMOS memory when the system isn’t turned on.

X – ITE 8211 controller (not fitted)

This is an optional feature which is not offered by Viglen.

Z – Intel® 82915G Graphics Memory / Controller Hub (GMCH)

The Intel® 915G graphics memory controller hub (GMCH) and the ICH6 I/O

controller hub provide the vital interfaces for the motherboard. The GMCH features

the Intel® Graphics Media Accelerator 900, an integrated graphics engine for

enhanced 3D, 2D, and video capabilities. The GMCH provides the interface for a

processor in the 775-land package with 533/800 MHz front side bus (FSB), dual

channel DDR at speeds of up to 400 MHz, and PCI Express x16 interface for a

graphics card.

AA – PCI Express x1 bus add-in card

Allows a PCI Express x1 device to be fitted to the motherboard. E.g. Fire wire card

BB – SPIDIF_OUT (not supported)

This is an optional feature which is not offered by Viglen.

Vig560s Motherboard Manual

15

Back Panel Connectors

The motherboard external IO connectors are attached to a metallic I/O shield. This

shield serves several purposes:

• It protects the sensitive motherboard from any external EMC interference.

• It stops the computer from interfering with other electrical devices.

• It allows the motherboard to be easily upgraded in the future without having to

resort to buying a whole new case. Simply change the I/O shield to match the

motherboard.

The I/O shield provides external access to PS/2 keyboard and mouse connectors as

well as one serial port, one parallel port, four USB ports, one LAN Port and the audio

connectors.

Figure 3: Rear I/O Shield

Note: Power to the computer should be turned off before a keyboard or mouse is

connected or disconnected.

(1) PS/2 Mouse Port (Green)

This port is for a PS/2 mouse

(2) Parallel Port

The 25-pin port connects a parallel printer, a scanner, or other devices.

(3) LAN (RJ-45) port

This port allows 10/100/1000 Mbps connection to a Local Area Network (LAN)

through a network hub.

Vig560s Motherboard Manual

16

(4) Rear Speaker Out Port (Gray)

This port connects to the rear speakers on a 4-channel, 6-channel or 8-channel

audio configuration

(5) Side Speaker Out Port (Black)

This port connects to the side speakers in an 8-channel audio configuration.

(6) Line in Port (Light Blue)

This port connects a tape, CD, DVD player or other audio sources.

(7) Line Out Port (Lime)

This port connects a headphone or a speaker. In 4-channel, 6-channel, and 8-

channel mode, the function of this port becomes Front Speaker Out.

(8) Microphone Port (Pink)

This port connects to a microphone.

(9) Center/Subwoofer Port (Yellow Orange)

This port connects the center/subwoofer speakers.

Table 2: Audio 2, 4, 6, or 8-Channel Configuration

Port Headset

2-Channel

4-Channel 6-Channel 8-Channel

Light Blue

Line In Line In Line In Line In

Lime

Line Out Front Speak Out Front Speaker Out Front Speaker Out

Pink

Mic In Mic In Mic In Mic In

Grey

- Rear Speaker Out Rear Speaker Out Rear Speaker Out

Black

- - - Side Speaker Out

Yellow Orange

- - Center/Subwoofer Center/Subwoofer

(10) USB 2.0 Ports 3 and 4

These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB

2.0 devices.

(11) USB 2.0 Ports 1 and 2

These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB

2.0 devices.

(12) Video Graphics Adapter Port

This 15-pin port is for a VGA monitor or other VGA-compatible devices.

Vig560s Motherboard Manual

17

(13) Serial Port

This 9-pin COM1 port is for pointing devices or other serial devices.

(14) PS/2 Keyboard Port (Purple)

This port is for a PS/2 keyboard.

Vig560s Motherboard Manual

18

Chapter 2: System Board Options

The VIG560S motherboard is capable of accepting Pentium® 4 CPU’s. RAM can be

upgraded to a maximum of 4GB using DDR333/400 SDRAM DIMMs Non ECC

Unbuffered memory.

WARNING!

Unplug the system before carrying out the procedures described in this

chapter. Failure to disconnect power before you open the system can result

in personal injury or equipment damage. Hazardous voltage, current, and

energy levels are present in this product. Power switch terminals can have

hazardous Voltages present even when the power switch is off.

The procedures assume familiarity with the general terminology associated

with personal computers and with the safety practices and regulatory

compliance required for using and modifying electronic equipment.

Do not operate the system with the cover removed. Always replace the cover

before turning on the system.

As the colours of the wires in the mains lead of this computer may not correspond with the

coloured markings identifying the terminals in your plug precede as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug

which is marked by the letter E or by the safety Earth symbol or coloured green or

green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with

the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with

the letter L or coloured red.

Vig560s Motherboard Manual

19

Make sure you are earthed and free of static charge before you open the computer

case. If you are unsure about upgrading your computer, return it to Viglen so a

qualified engineer can perform the upgrade.

STEPS TO TAKE TO PREVENT STATIC DISCHARGE:

1. The best way to prevent static discharge is to buy an anti-static strap from your

local electrical shop. While you are wearing the strap and it is earthed, static

charge will be harmlessly bled to ground.

2. Do not remove the component from its anti-static protective packaging until you

are about to install it.

3. Hold boards by the edges - try not to touch components / interface strips etc.

Note: We recommend that you return your computer to the service department for

upgrading. Any work carried out is fully guaranteed. Upgrades should only be carried

out by persons who are familiar with handling IC's, as incorrect installation will

invalidate the guarantee.

CAUTION!

The Viglen Vig560s motherboard

and associated components are

sensitive electronic devices. A small

static shock from your body can

cause expensive damage to your

equipment.

Page is loading ...

Viglen Vig566s User manual

Viglen Vig566s User manual

Related papers

Other documents