DFI EC510-HD/EC511-HD/EC520-HD/EC521-HD User manual

www.d.com

1

Chapter 1 Introduction

EC510/511/520/521-HD

Modular-Designed Embedded System

User’s Manual

A37910551

www.d.com

2

Chapter 1 Introduction

Copyright

This publication contains information that is protected by copyright. No part of it may be re-

produced in any form or by any means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions

or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthatto whichthereceiver

is connected.

• ConsultthedealeroranexperiencedradioTVtechnicianforhelp.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

www.d.com

3

Chapter 1 Introduction

Table of Contents

Copyright .............................................................................................................2

Trademarks ........................................................................................................2

FCC and DOC Statement on Class A .....................................................2

About this Manual ..........................................................................................4

Warranty ..............................................................................................................4

Static Electricity Precautions ......................................................................4

Safety Measures ..............................................................................................4

Safety Precautions .......................................................................................... 5

About the Package .........................................................................................5

Chapter 1 - Introduction .............................................................................6

Overview.........................................................................................................6

Key Features..................................................................................................6

Specifications ................................................................................................7

Getting the Know the EC510/EC511/EC520/EC521-HD .................... 9

Mechanical Dimensions ............................................................................ 10

Chapter 2 - Getting Started �� 12

Preparing the system ................................................................................ 12

Installing Devices ....................................................................................... 12

Configuring the BIOS ................................................................................ 12

Installing the Operating System ............................................................ 12

Installing the Drivers ................................................................................ 12

Chapter 3 - Installing the Devices ...................................................... 13

Removing the Chassis Cover ................................................................. 13

Installing the SODIMM ............................................................................ 14

Installing the 2.5” SATA Drive .............................................................. 15

Installing the Mini PCIe and/or mSATA Card ................................... 17

Installing the PCI and PCIe Expansion Cards .................................. 18

Installing the CPU .................................................................................... 21

Chapter 4 - Jumper Settings �� 24

Jumper Setting - System Board

Clear CMOS Data

....................................................................................... 24

USB Power Select ...................................................................................... 24

Auto Power-on Select ............................................................................... 25

PS/2 Keyboard/Mouse Power Select ..................................................... 25

COM 1/COM 2 RS232/422/485 Select ................................................. 26

COM 1/COM 2 RS232/Power Select ..................................................... 27

Mini PCIe Signal Select ............................................................................ 27

Mini PCIe Power Select ............................................................................ 28

Jumper Setting - I/O Board (for EC510/EC511-HD)

USB Power Select

...................................................................................... 28

COM 7/COM 8 RS232/422/485 Select ................................................. 28

COM 7/COM 8 RS232/Power Select ..................................................... 29

Digital I/O Power Select .......................................................................... 29

Chapter 5 - Ports and Connectors �� 30

Front Panel I/O Ports ................................................................................ 30

VGAPort .................................................................................................... 31

RJ45 LAN Ports ........................................................................................... 31

COM (Serial) Ports ...................................................................................... 32

USB Ports ................................................................................................... 33

DC-in ......................................................................................................... 33

8-bit GPIO .................................................................................................. 34

I/O Connectors ........................................................................................... 34

Power Connector ........................................................................................ 34

Parallel Connector ....................................................................................... 35

Front Panel Connector ................................................................................ 35

Cooling Fan Connectors............................................................................... 36

SMBus Connector ....................................................................................... 37

Chassis Intrusion Connector ........................................................................ 37

SATA (Serial ATA) Connectors ...................................................................... 38

SATA (Serial ATA) Power Connectors ............................................................ 38

PS/2 Keyboard/Mouse Connector ................................................................. 39

Expansion Slots .......................................................................................... 40

Standby Power LED .................................................................................... 41

Battery ....................................................................................................... 41

Chapter 6 - Mounting Options .............................................................. 42

Wall Mount ................................................................................................... 42

Chapter 7 - BIOS Setup �� 44

Overview....................................................................................................... 44

AMI BIOS Setup Utility ............................................................................. 45

Main .......................................................................................................... 45

Advanced ................................................................................................... 45

Chipset ...................................................................................................... 55

Boot........................................................................................................... 63

Security ...................................................................................................... 64

Save & Exit ................................................................................................. 64

Updating the BIOS .................................................................................... 65

Notice: BIOS SPI ROM ............................................................................. 65

Chapter 8 - Supported Software .......................................................... 66

Chapter 9 - Digital I/O Programming Guide .................................... 87

Appendix A - Watchdog Sample Code................................................ 89

Appendix B - System Error Message ................................................... 90

Appendix C - Troubleshooting ................................................................ 91

www.d.com

4

Chapter 1 Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual in the CD, in-

sert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear. Click

“User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper instal-

lation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in or

out of warranty. It must be returned to the purchase point, factory or authorized service

agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the

product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are

ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts

or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con

nectors by their ends.

Safety Measures

To avoid damage to the system:

•UsethecorrectACinputvoltagerange.

To reduce the risk of electric shock:

•Unplugthepowercordbeforeremovingthesystemchassiscoverforinstallationor

servicing. After installation or servicing, cover the system chassis before plugging the power

cord.

Battery:

•Dangerofexplosionifbatteryincorrectlyreplaced.

•Replaceonlywiththesameorequivalenttyperecommendbythemanufacturer.

•Disposeofusedbatteriesaccordingtolocalordinance.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other com-

ponents. Perform the upgrade instruction procedures described at an ESD worksta-

tion only. If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the system chas-

sis. If a wrist strap is unavailable, establish and maintain contact with the system

chassis throughout any procedures requiring ESD protection.

www.d.com

5

Chapter 1 Introduction

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

•1systemunit

•1CDdiskincludes:Drivers/Manual

•1QuickInstallationGuide

Optional Items

•WallMountkit

•PowerCord

•PowerAdapter:120W,19V/6.31A

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Safety Precautions

• Use the correct DC input voltage range.

• Unplug the power cord before removing the system chassis cover for installation or servic-

ing. After installation or servicing, cover the system chassis before plugging the power cord.

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufacturer.

• Dispose of used batteries according to local ordinance.

• Keep this system away from humidity.

• Place the system on a stable surface. Dropping it or letting it fall may cause damage.

• The openings on the system are for air ventilation to protect the system from overheating.

DONOTCOVERTHEOPENINGS.

• Place the power cord in such a way that it will not be stepped on. Do not place anything on

top of the power cord. Use a power cord that has been approved for use with the system

and that it matches the voltage and current marked on the system’s electrical range label.

• If the system will not be used for a long time, disconnect it from the power source to avoid

damage by transient overvoltage.

• If one of the following occurs, consult a service personnel:

- The power cord or plug is damaged.

- Liquid has penetrated the system.

- The system has been exposed to moisture.

- The system is not working properly.

- The system dropped or is damaged.

- The system has obvious signs of breakage.

• The unit uses a three-wire ground cable which is equipped with a third pin to ground the

unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does

not support this kind of plug, contact your electrician to replace the outlet.

• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use

liquid or spray detergents for cleaning.

www.d.com

6

Chapter 1 Introduction

Chapter 1 - Introduction

Chapter 1

Overview

Key Features

Model Name EC510/EC511/EC520/EC521-HD

Processor 4th Generation Intel

®

Core

TM

processors

Chipset Intel

®

H81 Express Chipset

LAN EC510/EC511-HD: 5 LAN ports

EC520/EC521-HD: 2 LAN ports

COM 6 COM ports

Display 1VGA

USB 2 Type A USB 2.0 ports, 2 Type A USB 3.0 ports

Power 9~36VDC-in

Front View (EC510/EC511-HD)

Front View (EC520/EC521-HD)

www.d.com

7

Chapter 1 Introduction

Front Panel I/O

Ports

•1powerbuttonwithLED

•1resetbutton

•1StatusLED

•1HDDLED

•1VGAport

•5RJ45LANports

•2TypeAUSB2.0ports

•2TypeAUSB3.0ports

•4DB-9RS232/422/485serialports(withpower)

•2DB-9RS232serialports

•19~36VDC-in3-poleterminalblock

•28-bitGPIO9-poleterminalblocks

Power

•Powerinputvoltage:9~36VDC-in

Environment

•Temperature

- Operating: 0

o

C ~ 45

o

C

- Storage: -20

o

C ~ 85

o

C

•OperatingVibration

- IEC68-2-64

•OperatingShock

- Half sine wave 3G, 11ms, 3 shock per axis

Construction

•Aluminum+SGCC

Mounting

•Wallmount

- Mounting brackets and screws* (optional)

Dimensions

•235mmx102.5mmx222mm(WxHxD)

Weight

•TBD

OS Support

•WindowsXP(32-bit)(limited function), Windows 7, WES 7, WE8S

•Linux(Distributionavailableuponrequest)

Other Features

•Watchdogtimeoutprogrammableviasoftwarefrom1to255seconds

Certication

•CE

•FCCClassA

•RoHS

Specifications (EC510/EC511-HD)

Processor System

- 4th Generation Intel

®

Core

TM

processors (22nm process technology)

: Intel

®

Core

TM

i7-4770TE (8M Cache, up to 3.3 GHz); 45W

: Intel

®

Core

TM

i5-4590T (6M Cache, up to 3.0 GHz); 35W

: Intel

®

Core

TM

i5-4570TE (4M Cache, up to 3.3 GHz); 35W

: Intel

®

Core

TM

i3-4350T (4M Cache, 3.1 GHz); 35W

: Intel

®

Core

TM

i3-4340TE (4M Cache, 2.6 GHz); 35W

: Intel

®

Core

TM

i3-4330TE (4M Cache, 2.4 GHz); 35W

: Intel

®

Pentium

®

G3320TE (3M Cache, 2.3 GHz); 35W

: Intel

®

Celeron

®

G1820TE (2M Cache, 2.2 GHz); 35W

Chipset

•Intel

®

H81 Express chipset

Memory

•Two204-pinDDR3SODIMMsockets

•SupportsDDR31333/1600MHz

•Supportsupto16GBsystemmemory

•Supportsdualchannelmemoryinterface

Graphics

•Intel

®

HD Graphics

•Displayports:1VGA

•VGA:24-bit,resolutionupto1920x1200@60Hz

Storage

•22.5"SATAdrivebays

- SATA 3.0 port with data transfer rate up to 6Gb/s

•Supports1mSATAmoduleviatheminiPCIesocket

Ethernet

•1Intel

®

I210 PCI Express Gigabit Ethernet controller

•1Intel

®

I217 Gigabit Ethernet Phy

•3Intel

®

WG82574L PCI Express Gigabit Ethernet controllers

•Integrated10/100/1000transceiver

•FullycompliantwithIEEE802.3,IEEE802.3u,IEEE802.3ab

Expansion

•EC510

- 1 PCI slot

- 1 Mini PCIe slot

: Supports USB and PCIe signals

: Supports mSATA, Wi-Fi or 3G*

: Supports half size or full size Mini PCIe card

•EC511

- 1 PCIe x16 slot

- 1 Mini PCIe slot

: Supports USB and PCIe signals

: Supports mSATA, Wi-Fi or 3G*

: Supports half size or full size Mini PCIe card

Chapter 1

Note:

*Optional and is not supported in standard model. Please contact your sales represen-

tative for more information.

www.d.com

8

Chapter 1 Introduction

Chapter 1

Front Panel I/O

Ports

•1powerbuttonwithLED

•1resetbutton

•1StatusLED

•1HDDLED

•1VGAport

•2RJ45LANports

•2TypeAUSB2.0ports

•2TypeAUSB3.0ports

•2DB-9RS232/422/485serialports(withpower)

•4DB-9RS232serialports

•19~36VDC-in3-poleterminalblock

Power

•Powerinputvoltage:9~36VDC-in

Environment

•Temperature

- Operating: 0

o

C ~ 45

o

C

- Storage: -20

o

C ~ 85

o

C

•OperatingVibration

- IEC68-2-64

•OperatingShock

- Half sine wave 3G, 11ms, 3 shock per axis

Construction

•Aluminum+SGCC

Mounting

•Wallmount

- Mounting brackets and screws* (optional)

Dimensions

•235mmx102.5mmx222mm(WxHxD)

Weight

•TBD

OS Support

•WindowsXP(32-bit)(limited function), Windows 7, WES 7, WE8S

•Linux(Distributionavailableuponrequest)

Other Features

•Watchdogtimeoutprogrammableviasoftwarefrom1to255seconds

Certication

•CE

•FCCClassA

•RoHS

Specifications (EC520/EC521-HD)

Processor System

- 4th Generation Intel

®

Core

TM

processors (22nm process technology)

: Intel

®

Core

TM

i7-4770TE (8M Cache, up to 3.3 GHz); 45W

: Intel

®

Core

TM

i5-4590T (6M Cache, up to 3.0 GHz); 35W

: Intel

®

Core

TM

i5-4570TE (4M Cache, up to 3.3 GHz); 35W

: Intel

®

Core

TM

i3-4350T (4M Cache, 3.1 GHz); 35W

: Intel

®

Core

TM

i3-4340TE (4M Cache, 2.6 GHz); 35W

: Intel

®

Core

TM

i3-4330TE (4M Cache, 2.4 GHz); 35W

: Intel

®

Pentium

®

G3320TE (3M Cache, 2.3 GHz); 35W

: Intel

®

Celeron

®

G1820TE (2M Cache, 2.2 GHz); 35W

Chipset

•Intel

®

H81 Express chipset

Memory

•Two204-pinDDR3SODIMMsockets

•SupportsDDR31333/1600MHz

•Supportsupto16GBsystemmemory

•Supportsdualchannelmemoryinterface

Graphics

•Intel

®

HD Graphics

•Displayports:1VGA

•VGA:24-bit,resolutionupto1920x1200@60Hz

Storage

•22.5"SATAdrivebays

- SATA 3.0 port with data transfer rate up to 6Gb/s

•Supports1mSATAmoduleviatheminiPCIesocket

Ethernet

•1Intel

®

I210 PCI Express Gigabit Ethernet controller

•1Intel

®

I217 Gigabit Ethernet Phy

•Integrated10/100/1000transceiver

•FullycompliantwithIEEE802.3,IEEE802.3u,IEEE802.3ab

Expansion

•EC520

- 2 PCI slots

- 1 Mini PCIe slot

: Supports USB and PCIe signals

: Supports mSATA, Wi-Fi or 3G*

: Supports half size or full size Mini PCIe card

•EC521

- 1 PCI slot

- 1 PCIe x16 slot

- 1 Mini PCIe slot

: Supports USB and PCIe signals

: Supports mSATA, Wi-Fi or 3G*

: Supports half size or full size Mini PCIe card

Note:

*Optional and is not supported in standard model. Please contact your sales represen-

tative for more information.

www.d.com

9

Chapter 1 Introduction

Getting to Know the EC510/EC511/EC520/EC521-HD

Chapter 1

Front View (EC510/EC511-HD)

Front View (EC520/ECC521-HD)

USB Ports

Used to connect USB 2.0/1.1 devices.

COM Ports

Used to connect serial devices.

VGAPort

UsedtoconnectaVGAdevice.

LAN Ports

Used to connect the system to a local area network.

DC-in

Used to plug a power adapter.

GPIO

Supports 16-bit digital output and input.

Expansion slots

Supports to add riser cards.

Power button

Press to power-on or power-off the system.

Reset Button

Press to reset the system.

HDD LED

Indicates the status of the hard drive.

Status LED

Indicates the status as below.

COM 1

Power Button

Status LED

Reset ButtonUSB 2.0

LAN 3~5

Expansion Slot

DC-in

USB 3.0

LAN 1~

2

VGA

GPIO COM 7~8 COM 2~4

GPIO

Expansion Slots COM 2~6

COM 1

Reset ButtonUSB 2.0

DC-in

USB 3.0

LAN 1~

2

VGA

HDD LED

Power Button

Status LED

HDD LED

Note:

The cables for COM 2 to COM 6 are available upon request.

Status LED

Suspend Mode S0 S1 S3 S4, S5

LED Action

Always ON

QuickBlink

(cycle 1 sec)

Slow Blink

(cycle >1 sec)

OFF

www.d.com

10

Chapter 1 Introduction

Mechanical Dimensions

Chassis Dimensions (EC510/EC511-HD)

Chapter 1

Front View

Right View

Left View

102.50

6.00

235.00

222.00

Rear View

Chassis Dimensions (EC520/C521-HD)

Front View

Right View

Left View

102.50

6.00

235.00

222.00

Rear View

www.d.com

11

Chapter 1 Introduction

Motherboard Dimensions

7.00

0.00

10.00

15.46

25.73

31.50

51.01

80.29

99.29

118.43

138.43

164.01

200.00

205.50

218.00

228.00

72.00

156.00

161.02

209.55

211.93

117.00

16.80

21.00

0.00

34.00

55.00

110.73

98.57

106.44

120.19

210.00

215.00

63.70

77.67

151.65

160.85

174.83

198.81

81.00

152.73

50.00

61.27

152.73

206.89

98.57

Chapter 1

www.dﬁ .com

12

Chapter 2 Getting Started

Chapter 2 - Getting Started

Chapter 2

Preparing the System

Before you start using the system, you need the following items:

• SATA hard drive

• AC power adapter

• CD-ROM drive (for installing software/drivers)

• Memory module

Installing Devices

The following are devices that can be installed in the system.

• Memory module

• SATA hard drive

• Mini PCIe card

Configuring the BIOS

To get you started, you may need to change configurations such as the date, time and the

type of hard disk drive.

1. Power-on the system.

2. After the memory test, the message “Press DEL to run setup” will appear on the screen.

Press the Delete key to enter the AMI BIOS setup utility.

Installing the Operating System

Most operating system software are provided in a CD therefore you need to install a CD-ROM

drive in order to use the CD.

Make sure a 2.5” SATA drive is already installed.

1. Refer to the following chapters for information on connecting a CD-ROM drive and install-

ing a SATA drive.

2. Refer to your operating system manual for instructions on installing the operating system.

Installing the Drivers

The system package includes a CD disk. The CD includes drivers that must be installed to pro-

vide the best system performance. Refer to the Supported Software chapter for instructions on

installing the drivers.

www.dﬁ .com

13

Chapter 3 Installing the Devices

Chapter 3

Chapter 3 - Installing the Devices

Removing the Chassis Cover

1. Make sure the system and all other peripheral devices connected to it have been powered-off.

2. Disconnect all power cords and cables.

3. The 6 mounting screws on the left side, right side and the bottom of the system are used to

secure the cover to the chassis. Remove these screws and then put them in a safe place for

later use.

4. After removing these mounting screws, lift the cover upward.

Lift the Cover Upward

5. The SODIMM sockets, Mini PCIe slot and SATA drive bay are readily accessible after remov-

ing the chassis cover.

Mounting Screw

SODIMM socket

Mini PCIe slot

SATA drive bay

Mounting Screw

www.dﬁ .com

14

Chapter 3 Installing the Devices

Chapter 3

Installing the SODIMM

1. The SODIMM sockets are located on the system board.

2. Note the key on the socket. The key ensures the module can be plugged into the socket in

one direction only.

3. Grasping the module by its edges, align the module into the socket at an approximately 30

degrees angle. Apply firm even pressure to each end of the module until it slips down into

the socket. The contact fingers on the edge of the module will almost completely disappear

inside the socket.

4. Push the module down until the clips at each end of the socket lock into the position. You

will hear a distinctive “click”, indicating the module is correctly locked into the position.

SODIMM Module

Clip Clip

SODIMM socket

www.dﬁ .com

15

Chapter 3 Installing the Devices

Chapter 3

Installing the 2.5” SATA Drive

1. The SATA drive bay is located on the system board.

2. Use the 4 provided mounting screws to secure the protective plate in place on the system

board.

Mounting Screws

Protective plate

3. Insert the SATA drive into the HDD bracket and secure it in place with the provided mount-

ing screws.

Mounting Screws

SATA drive

HDD bracket

Mounting Screw

SATA drive bay

Protective plate

www.dﬁ .com

16

Chapter 3 Installing the Devices

Chapter 3

4. Connect one end of the SATA data cable and the SATA power cable to a SATA data connec-

tor and a SATA power connector on the SATA drive respectively.

SATA power cable

SATA data cable

SATA power connector

SATA data connector

5. Place the SATA drive with the HDD bracket into the system. Align the mounting holes on

the HDD bracket with the mounting holes on the protective plate and then use the pro-

vided mounting screws to secure the drive in place.

SATA power cable

SATA data cable

6. Connect the other end of the SATA data cable and the SATA power cable to a SATA data

connector and a SATA power connector on the system board respectively.

Mounting Screw

SATA power connector

SATA data connector

SATA power connector

SATA data connector

SATA data

connector

SATA power

connector

www.dﬁ .com

17

Chapter 3 Installing the Devices

Chapter 3

3. Grasping the Mini PCIe card by its edges, align the card into the slot at an approximately 30

degrees angle. Apply ﬁ rm even pressure to each end of the card until it slips down into the

slot. The contact ﬁ ngers on the edge of the card will almost completely disappear inside the

slot.

Mini PCIe card

4. Push the Mini PCIe card down until the clips at each end of the latch lock into position. You

will hear a distinctive “click”, indicating the card is correctly locked into position.

Clip

Installing the Mini PCIe and/or mSATA Card

1.

The Mini PCIe slot is located on the system board

.

2. The system board is equipped with 1 Mini PCIe slot. The Mini PCIe slot supports a half length

or a full length Mini PCIe card. Note the key on the slot. The key ensures the Mini PCIe card

can be plugged into the slot in one direction only.

Mini PCIe slot

www.dﬁ .com

18

Chapter 3 Installing the Devices

Chapter 3

Installing the PCI and PCIe Expansion Cards

1. PCI slots and PCIe x16 slots on the riser cards are used to install the expansion cards. To

install the expansion cards, you need to remove the brackets from the chassis.

EC510/EC511-HD

PCI

Bracket

H320-1P for EC510-HD

EC510-HD

Bracket

H120-1E for EC511-HD

EC511-HD

PCIe x16

Important:

When inserting expansion cards into the system unit, please select a standard card

within 190mm (as the following pictures show) in order to fit expansion slots.

Mechanical Drawing for Expansion Card (EC510/EC511-HD)

Mechanical Drawing for Expansion Cards (EC520/EC521-HD)

www.dﬁ .com

19

Chapter 3 Installing the Devices

Chapter 3

2. To remove the brackets, the mounting screw on the front chassis has to be removed ﬁ rst.

EC510/EC511-HD

PCI

PCIe x16

PCI

PCIe x16

Brackets

H320-1P1E for EC521-HD

EC521-HD

EC520/EC521-HD

Brackets

PCI

EC520-HD

PCI

H320-2P for EC520-HD

EC520/EC521-HD

Mounting Screw

www.dﬁ .com

20

Chapter 3 Installing the Devices

Chapter 3

PCIe x16 card

PCI card

front View

PCI card

PCI

PCIe x16

EC520-HD

EC521-HD

3. Insert one expansion card with a bracket into PCIe slots and PCI slots respectively that are on

the riser card and secure the bracket in place.

EC510-HD

EC511-HD

PCI card

front View

PCI

front View

PCIe x16 card

PCIe x16

Page is loading ...

DFI EC510-HD/EC511-HD/EC520-HD/EC521-HD User manual

DFI EC510-HD/EC511-HD/EC520-HD/EC521-HD User manual

Related papers

Other documents