5.1 & 7.1 Channel
Surround Sound Setup
Panasonic Self Help
Guides
SC-BT100
DOC: UK/CCC/SH/SCBT100 V1.0
Setting up a 5.1
or 7.1 Speaker System
Setup
Press
Functions
Others
The SC-BT100 is supplied as a 3.1 surround sound system. Either one or two
sets of SH-FX67 wireless speakers can be added to upgrade the system to
become a 5.1 or .7.1 surround sound system. There are two stages:- first,
make the correct settings in the Speaker Setup menu on the main unit,
second, pair the wireless speakers
Before adding the rear wireless speakers it is necessary to activate the speaker
outputs (switch them on) in the speaker set-up menu please see the instructions
below:
Select Press You will see
Select BD
Eject the disk (If inside) to prevent it
from continually trying to read
Setup Continued
Sound
Arrow Down to
rear speakers
section
Select Press You will see
Speakers
5.1 / 7.1 Speaker
Arrow Down to
Activate the rear
speakers
At this point you have activated one set of rear speakers for a 5.1 surround sound
system. You must save your settings before your exit the speaker setup
menu. Please follow the instructions for saving the settings on the next
page.
If you have purchased a second set of rear speakers to create a 7.1 surround
sound system you will need activate them too. To do this please follow the
instructions on the next page
Setup Continued
Select Press You will see
7.1 Speaker
Arrow Down to
rear speakers
section
Arrow Down to
Activate the rear
speakers
Saving the Settings
Having activated the additional 5.1 or 7.1 speakers in the speaker setup menu, the
settings must be saved before exiting the menu. Please follow the instructions
below:
Arrow left to move the
active box to the left
Arrow up until
“Complete” is
highlighted in Yellow
Press the return button
on the remote
repeatedly until you
have completely exited
the menus
Press “OK” To Save
and complete
Pairing the additional
Speaker System (s)
The second stage to upgrading the SC-BT100 to become a 5.1 or 7.1
surround sound system is to pair the additional set or sets of wireless
surround speakers (SH-FX67).
Each SH-FX67 wireless speaker system comprises of:
2 Speakers
1 SH-FX67T Digital Transmitter Card
1 SE-FX67 Wireless Receiver
•One Wireless Speaker system can be added to the SC-BT100 to create a 5.1
surround sound system.
•Two Wireless Speaker systems can be added to the SC-BT100 to create a 7.1
surround sound system
If only one SH-FX67 wireless speaker system is being used (5.1 channel surround
sound system) no pairing will be necessary as the Digital Transmitter card and the
Wireless Receiver will have already been paired at the factory. Simply insert the
Digital Transmitter into the back of the home theatre unit (SC-BT100) as illustrated
If two SH-FX67 wireless speaker systems are being used, (7.1 channel surround
sound system) only one Digital Transmitter card is used
to send the signals to both
Wireless Receivers. The second Digital Transmitter card should be stored in a safe
place as a spare. Paring the one Digital Transmitter card with the second Wireless
Receiver will be required. Please see the Pairing instructions
When using a single Wireless
Receiver in a 5.1 channel surround
sound system as shown in the
illustration, ensure that the surround
selector switch, found on the back of
the receiver, is set to the Centre
position
When using a pair of Wireless
Receivers in a 7.1 channel surround
sound system as shown in the
illustration, ensure that the surround
selector switch, found on the back of
the receiver, is set to the “L” position
on the left receiver and in the “R”
position on the right receiver
Pairing Instructions
(for 7.1 Channel Surround Sound only)
It should not be necessary to pair the Digital Transmitter to the Wireless Receiver unit when a single
receiver is being used (5.1 channel surround system) as they will have been paired at the factory.
When creating a 7.1 channel surround sound system please follow the instructions below:
1. Select one Wireless Receiver and the Digital Transmitter card
supplied with it and place it in position for the left hand
channels.
2. Insert the Digital Transmitter Card into the rear of the home
theatre system
3. Set the surround selector switch to the “L” (left) position.
4. Position the second Wireless Receiver in its location for the
right hand channels and set the surround selector switch to the
“R” (right) position. The Transmitter card for the second
receiver should be stored in a safe place as a spare.
5. Turn on the Home Theatre System and turn the volume low.
6. Connect the mains power to the right hand Wireless Receiver
only and turn on.
7. While pressing the Skip button on the top front of the home
theatre system, also press the number 3 button on the remote
control for a few seconds until the “P” appears on the Home
Theatre display.
8. While “P” appears on the Home Theatre display, press the “ID
Set” button on the rear of the right hand Wireless Receiver,
using a pointed object such as a ball point pen.
9. Switch off the right hand Wireless Receiver
10. Switch on both Wireless Receivers. Your surround speakers are
now ready to use.
+
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Panasonic SC-BT100 Owner's manual
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic SB-HS100 Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Fusion MS-BT100 Installation guide
-
Cambridge Audio CXR 120/200 User manual
-
Pioneer VSX-1121-K User manual
-
Elite Video VSX-33 User manual
-
CAMBRIDGE CXR200 Reference
-
-
-
-
-