Emprex D350PE Quick start guide

Brand: Emprex

Model: D350PE

Type: Quick start guide

Version 1.0 Sep. 2007

1 GENERAL INFORMATION

This Secure Drive Enclosure kit package contains:

• HDD Enclosure

• USB cable

• Software, Driver and Manual CD

• Quick Start Guide

• Power Adapter

• Screws / Screwdriver (for applicable models only)

2 GETTING STARTED

Hardware Installation

Assembling your hard drive to the Enclosure kit

1. Open the case with a screwdriver.

2. Gently lower the hard drive to rest

against the board.

Note: The pictures are only for illustration and actual accessories may

differ from picture.

3 SETTING UP

Security Software Setup

1. Insert the Installation CD into your CD-ROM drive.

Select “Software & Win98 driver”.

2. When this screen appears,

For Windows 98/SE:

Select “Install Win98 Driver” before proceeding to next

step.

For Windows XP/Me/2000/Vista

Select “Configure to Secure Drive”.

Caution:

Configuring to Secure Drive destroys any existing data. Be sure to

back up the disk contents first.

3. When this screen appears, follow the on-screen instructions.

1) Enter【New Password】

2) Re-enter【Confirm New Password】

3) At【Hint】prompt, enter a suitable phrase to help you recall

your password later on.

4) Click【Prepare Secure Drive】

When the installation is complete, please re-connect the USB

drive into the computer’s USB port for the new configuration to

take effect.

Note: In order to remove the device to take effect, you could choose either

device’ end or computer’s end (USB cable) to unplug and re-plug

the USB cable. Otherwise, system will still show the old data in the

drive.

Quick Start Guide

• Mac users please refer to Mac user guide in utility CD.

1. Pull out the tray of the

HDD case

2. Connect the tray to your

hard disk

3. Fasten the hard drive’s

mounting holes to the Case

rame with 2bigger screws.

4. Plug the LED power

connecter.

5. Push the hard disk into

the case.

6. Fasten the hard disk to the

case

7. Connect the USB/Power

cable to correct port.

8. Turn on the power switch.

Version 1.0 Sep. 2007

4 USING YOUR SECURE DRIVE

Password Authentication

Two Level Security Access

1. After you have re-plugged the Secure Drive into your

computer’s port, this Two Level Security Access window will

pop-up and prompt you to login. Enter both the password and

the security characters using the virtual keypad with a mouse

and click “Login”.

Disk content and Utility description

Disk Content:

SECURE DISK

Security HDD with data encrypted

CD PART

Virtual CD partition for auto-boot and includes

security utility

Security Utility in CD PART:

PAD_Secu.EXE

Security setup and password

setting/changing/resetting function before you

ONSPCSET.EXE

Security password Enable/disable utility

ONSPCPRT.EXE

Reset password utility, HDD data will be fully

erased!

Secure Disk

Follow these steps to check if the Secure Drive has been

properly configured. Windows automatically assigns the drive

letter.

i. In Windows Explorer, go to “My Computer”.

ii. When “Secure Disk” appears, your Secure Drive can now

used for storing data. (See Figure: My Computer)

Figure: My Computer

5 MANUAL SETTINGS

CD Partition

If the Security Access Window is not launched automatically

when you connect your Secure Drive, follow these steps:

i. In Windows Explorer, go to “My Computer”.

ii. Open “CD-PART”. (See Figure My Computer)

PAD Security Utility program

In My Computer menu, the CD PART Window, double click

“PAD_Secu.exe”

Password Security Manager

Whenever you change any password settings, the data in the

Secure Drive will not be effected.

Note: It is important not to forget your password. Otherwise, you will need

to re-configure to Secure Drive that will erase both the password

and data in the Secure Drive.

CD PART

Secure Disk

3100554160 V1.0 Sep. 2007

Security Characters

Use Virtual Keypad (see

below) to enter password or

Security Characters seen at

the Security Image on the right.

Hint

Enter a phrase to help you

recall the password you have

entered in the event that you

forget your password.

Current Password

Use Virtual Keypad

(see below) to enter current password.

New Password &

Confirm New Password

Enter minimum 4 characters password.

Disable Password Security

This box must be checked

disable password.

irtual Keypad

Use your mouse to click on the buttons in the Virtual Keypad to enter

password or Security Characters seen at the Security Image.

For advanced settings, please refer to user’s manual in utility CD

Emprex D350PE Quick start guide

Emprex D350PE Quick start guide

Emprex D350PE Quick start guide

Related papers

Other documents