EuroLite ColorSpot Par 64 Operating instructions

Brand: EuroLite

Model: ColorSpot Par 64

Type: Operating instructions

1 of 4 pages

ColorSpot Par 64

Operation

Manual

The ColorSpot Par 64 15 5W LED is a IP65 rated exterior LED fixture featuring four-in-one

RGBW LED diodes. With a total power consumption of 95 Watts the ColorSpot 64 is an energy

efficient fixture capable of providing a smooth color wash effects. Set up and control is done via a

wireless remote IR receiver which is on the face of the unit. Once set up, the unit can be operated from

DMX with 4 different DMX control modes, and features built in macro programs all of which can be

accessed via DMX or the optional wireless remote IR controller. You can daisy chain power up to 7

fixtures with 2, 5, & 10 meter cables. Designed and built with a rugged aluminum die cast housing and

internal thermal protection to ensure long life and operation.

Specification:

1.Weight: 11lbs

2. Size: 9.8”×7.4”×11.8”

3. Power input:AC100V-240V/50HZ-60HZ

4. Wattage:95W

5. LEDS: 15PCS 5W (4 in one)

6. Beam angle of LEDs: 40 degree

7. 3PIN female and male XLR socket, 4 PIN female and male power socket

8. 4-button LED digital display

9. IR remote available

2 of 4 pages

10. IP rate: IP 65

It has seven kinds of operation mode, they are as

follows:

Static color select mode, Manual dimmer color mode, Color change mode, Color dreaming

mode

Auto-run mode, Slave mode, DMX

mode

Here above seven kinds running mode are selected by MODE button. Press MODE and UP button at

the same time, when it is on, you can initialize it at extra factory setting, running on the auto-

run program mode. To make the display stay on all of the time press the MODE and UP buttons

at the same time. To make the display turn off after 20 seconds, press the MODE and DOWN

buttons at the same time.

1. Static color select

mode

Press “MODE ” button, select static color select mode. four digital tube d

isplays

“

. ××”,

Press “UP” or “DOWN” to select static colors 0-15 under this mode. Then press SET UP button to

choose the flash speed mode.When“FS.××” is displayed, press “UP” or “DOWN” button to adjust

the flash speed(00-99), “0”is turn off flash,1 is the slowest,99 is the fastest.

2. Manual dimmer color

mode

Press “MODE” button, select manual dimmer color mode. At this time, four digital tube

displays“r.×

××”.Press “SET UP” to choose the display 4 colors, red“r.×××”,green“G. ×××”,

blue“b.

× × × ” and w

hite

“ h. × × × ” ,then press “UP” or “DOWN” button to set the dimming

rate (0-255).Then press SET UP button to choose the flash speed mode.When“FS.××” is displayed,

press “UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off flash,1 is the

slowest,99 is the fastest.

3. Color change

mode

Press “MODE” button, select color change mode. At this time, the four digital tube

displays“JP.××” . Press UP or DOWN to select the color change speed grade 1-99 under this

mode.(From slow to quick) Then press SETUP button to choose the flash speed

mode.When“FS.××” is displayed, press “UP” or “DOWN” button to adjust the flash speed(00-

99), “0”is turn off flash,1 is the slowest,99 is the fastest.

4. Color dreaming

mode

Press “MODE” button, select color dreaming mode. At this time, the four digital tube displays

“

Fd.×

3 of 4 pages

×”.Press UP or DOWN to select the color dreaming speed grade 1-99 under this mode.(From

slow to quick).Then press SETUP button to choose the flash speed

mode.When“

FS.××” is

displayed, press “UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off

flash,1 is the slowest,99 is the fastest.

5. Auto-run

mode

Press “MODE” button, “AUTO.” is displayed, the color change program and color dreaming

program run alternatively. Then press SETUP button to choose the flash speed

mode.When“FS. × × ” is displayed, press “UP” or “DOWN” button to adjust the flash

speed(00-99), “0”is turn off flash,1 is the slowest,99 is the fastest.

6. Slave

mode

Press “MODE” button, select slave mode. At this time, the four digital tube displays

“SLAu.”.Press SET UP,UP or DOWN is no use under this mode.

7. DMX

mode

Press “MODE” button, select DMX mode. At this time, the four digital tube d

isplay

s“d.

× × × ”,then press “UP” or “DOWN” to select the DMX address 1-512.When there is no

controller signal, the four digital tube display will be flash.

DMX MODE:7 channels

mode

CH7

CH5

CH4

CH3

CH2

CH1

MODE

DMX VALUE

FUNCTION

0-3

No function

Strobe

11-255 (slow

ick

)

Dimming

0-255

(dim→

bright)

White

0-255

(dim→

bright)

Blue

0-255

(dim→

bright)

Green

0-255

(dim→

bright)

Red

0-255

(dim→

bright)

4-17

function

18-31

Green

32-45

Blue

46-59

White

60-73

R+

74-87

R+B

88-101

R+W

102-115

G+B

116-129

130-143

B+W

144-157

R+G+B

158-171

R+G+W

172-185

R+B+W

4 of 4 pages

186-199

G+B+W

200-213

R+G+B+W

214-227

Color change

Spee

0-255

(slow→

228-241

Color dreaming

242-255

Auto run

Note:R---red G---green B---blue W---white

11. Operation by IR remote:

You can also operate this product by IR remote, the distance available is at most

10M. Notice: IR remote is ready to control the unit which is any

working mode. The picture of the IR remote:

AUTO RUN mode

Press “AUTO RUN” to choose Auto run mode. Press FLASH to turn on/off the flash of the

Auto Run, and then pressing “+” and “-“ buttons to adjust flash speed.

Select program Mode

1. Press PROG to go in to static color select mode , color change mode or color dreaming mode

2. Press “+” or “-” or button 1-9 to choose static color when it go into the color select mode.

3.Press FLASH to turn on/off flash and press “+” or “-” to adjust the flash speed. Press

SPEED to set the program running speed (effective only color change mode and color dreaming

mode)and press “+” or “-” to adjust it.

M/S mode

Press SL to display SLAV mode. The R/G/B/W lights are off when without master

light

Select light program mode

Press R/G/B/W to choose R/G/B/W colors and pressing “+” and “-” buttons to adjust the

intensity of the light. Press FLASH to turn on/off flash effect to in this situation, pressing “+”

and “-” buttons to adjust the flash speed.

DMX MODE

5 of 4 pages

Press D to display DMX mode. The R/G/B/W lights will flash 2~3 times indicates that the LED

light has been set to DMX mode.

Set ADDR

Press this button to set the DMX address or initialize the program, then the red, green ,blue and

white lights will flash 2~3 times. Please put in 3 number ,for example, 1 2 3. After the red light is on,

please put in the first number. After the first number is accessed the green light will be on, then put in

the second number. When the blue light will be on, please put in the third number. After all the three

number are put in, the red, green ,blue and white lights will flash 2~3 times, which indicate that the

DMX address is right and it go in to the DMX MODE automatically. If the address is wrong the red

light will be on. New DMX address should be put in.

If the 951 are put in, red and green lights will be on. Put “0” to initialize the program. If the wrong

address is put in, the red light will be on, indicating new address should be put in. Then the system

will run in the designed mode.

Black Out mode

Press “BLACK OUT” to set the LED lights power on or power off by pressing this button.

EuroLite ColorSpot Par 64 Operating instructions

EuroLite ColorSpot Par 64 Operating instructions

EuroLite ColorSpot Par 64 Operating instructions

Related papers

Other documents