ViSAGE VIS0495 Operating instructions

Brand: ViSAGE

Model: VIS0495

Type: Operating instructions

ViSAGE VIS0495 is a versatile lighting device designed for various entertainment and decorative applications. With its seven operation modes, it offers a wide range of dynamic and colorful light effects.

In Static Color Select mode, you can choose from 15 static colors and adjust their brightness. The Manual Dimmer Color mode allows you to dim and set the intensity of four individual colors: red, green, blue, and white.

For more dynamic effects, the Color Change mode provides adjustable color-changing speeds, while the Color Dreaming mode creates a gradual color-fading effect. The Auto-Run mode combines both color change and color dreaming programs for an alternating display.

1 of 4 pages

VIS0495 Operation Manual

VIS0495 can make very bright colorful and dynamic light scenery effects. It is widely applied to

entertainment hall, stage, social club and outdoor building decoration.The front operation plant has four

digital tube display.You can operate it through the four buttons---MODE,SET UP,UP,DOWN. It can

stock running mode when it is off.You can find last running mode when it is on next time.This product

has temperature protect function.When it is on,it will be off automatically when the temperature is

beyond 85 C.But it won’t impact other combined products.When you re-start it,it can run correctly

within 85 C.

A Specification:

1. Weight: 5.2kg

2. Size: 25 19 30cm

3. Power input: AC100V-240V/50HZ-60HZ

4. Wattage:50W

5. LEDS: 7PCS 8W (4 in one)

6. Beam angle of LEDs: 40 degree

7. 3PIN female and male XLR socket,4PIN female and male power socket

8. 4-button LED digital display

9. IR remote available

10. IP rate: IP 65

It has seven kinds of operation mode,they are as follows:

Static color select mode, Manual dimmer color mode, Color change mode, Color dreaming mode

Auto-run mode, Slave mode, DMX mode

Here above seven kinds running mode are selected by MODE button. Press MODE and UP button at

the same time, when it is on,you can initialize it at extra factory setting,running on the auto-run

program mode.To make the display stay on all of the time press the MODE and UP buttons at the

same time. To make the display turn off after 20 seconds, press the MODE and DOWN buttons at the

same time.

1. Static color select mode

Press“MODE ” button, select static color select mode. four digital tube displays CL. , Press

“UP” or “DOWN” to select static colors 0-15 under this mode.Then press SET UP button to choose

the flash speed mode.When“FS. ” is displayed,press “UP” or “DOWN” button to adjust the flash

speed(00-99), “0”is turn off flash,1 is the slowest,99 is the fastest.

2. Manual dimmer color mode

Press “MODE” button, select manual dimmer color mode.At this time,four digital tube displays r.

.Press “SET UP” to choose the display 4 colors, red r. ,green G. , blue b.

and white h. ,then press”UP” or “DOWN” button to set the dimming rate

(0-255).Then press SET UP button to choose the flash speed mode.When“FS. ” is displayed,press

“UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off flash,1 is the slowest,99 is

the fastest.

2 of 4 pages

3. Color change mode

Press“MODE” button,select color change mode.At this time,the four digital tube displays“JP. ” .

Press UP or DOWN to select the color change speed grade 1-99 under this mode.(From slow to quick)

Then press SETUP button to choose the flash speed mode.When“FS. ” is displayed,press “UP” or

“DOWN” button to adjust the flash speed(00-99), “0”is turn off flash,1 is the slowest,99 is the fastest.

4. Color dreaming mode

Press“MODE” button,select color dreaming mode.At this time,the four digital tube displays “Fd.

”.Press UP or DOWN to select the color dreaming speed grade 1-99 under this mode.(From slow to

quick).Then press SETUP button to choose the flash speed mode.When“FS. ” is displayed,press

“UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off flash,1 is the slowest,99 is

the fastest.

5. Auto-run mode

Press “MODE” button, “AUTO.” is displayed,the color change program and color dreaming program

run alternatively.Then press SETUP button to choose the flash speed mode.When“FS. ” is

displayed,press “UP” or “DOWN” button to adjust the flash speed(00-99), “0”is turn off flash,1 is the

slowest,99 is the fastest.

6. Slave mode

Press“MODE” button,select slave mode.At this time,the four digital tube displays “SLAu.”.Press SET

UP,UP or DOWN is no use under this mode.

7. DMX mode

Press “MODE” button,select DMX mode.At this time,the four digital tube displays“d. ”,then

press “UP” or “DOWN” to select the DMX address 1-512.When there is no controller signal,the four

digital tube display will be flash.

DMX MODE:7 channels mode

CH7 CH6 CH5 CH4 CH3 CH2 CH1

MODE

DMX VALUE

FUNCTION

1 0-3 No function

White

0-255

(dim→

bright)

Blue

0-255

(dim→

bright)

Green

0-255

(dim→

bright)

Red

0-255

(dim→

bright)

2 4-17 Red

3 18-31 Green

4 32-45 Blue

5 46-59 White

6 60-73 R+G

7 74-87 R+B

8 88-101 R+W

9 102-115 G+B

10 116-129 G+W

11 130-143 B+W

12 144-157 R+G+B

13 158-171 R+G+W

Strobe

11-255

(slow

quick)

Dimming

0-255

(dim→

bright)

function

3 of 4 pages

14 172-185 R+B+W

15 186-199 G+B+W

16 200-213 R+G+B+W

17 214-227 Color change

18 228-241

Color dreaming

242-255

Auto run

Speed

0-255

(slow

quick)

Note:R---red G---green B---blue W---white

11.

Operation by IR remote

You can also operate this product by IR remote, the distance available is at most 10M.

Notice:IR remote is ready to control the unit which is any working mode.

The picture of the IR remote:

Select program Mode

Press PROG button to cycle among static color select mode, color jumping mode,color dreaming

mode and auto run mode.Each press of this button will change to the next mode.

1. When the red color glow and then automatically off indicates that the LED par goes into the static

color select mode.You can press “+” and “-” or button 1-9 to choose static color in this mode.You can

also press FLASH to turn on/off flash and press “+”and “-” to adjust the flash speed.

2. When the green color glow and then automatically off indicates that the LED par goes into color

jumping mode,then press “+” and “-” to adjust color jumping speed.You can also press FLASH to turn

on/off flash and press “+”and “-” to adjust the flash speed.

3. When the blue color glow and then automatically off indicates that the LED par goes into color

dreaming mode,then press “+” and “-” to adjust color dreaming speed.You can also press FLASH to

turn on/off flash and press “+”and “-” to adjust the flash speed.

4. When the white color glow and then automatically off indicates that the LED par goes into auto run

mode.You can press FLASH to turn on/off flash and press “+”and “-” to adjust the flash speed.

M/S mode

Press SL/SA to display SLAV mode. The R/G/B/W lights are off when without master light.

4 of 4 pages

Select light program mode

Press R/G/B/W to choose R/G/B/W colors and pressing “+” and “-” buttons to adjust the intensity

of the light. Press FLASH to turn on/off flash effect to in this situation, pressing “+” and “-” buttons to

adjust the flash speed.

DMX MODE

Press D to display DMX mode. The R/G/B/W lights will flash 2~3 times indicates that the LED

light has been set to DMX mode.

Set ADDR

Press this button to set the DMX address or initialize the program, then the red, green ,blue and

white lights will flash 2~3 times. Please put in 3 number ,for example, 1 2 3. After the red light is on,

please put in the first number. After the first number is accessed the green light will be on, then put in

the second number. When the blue light will be on, please put in the third number. After all the three

number are put in, the red, green ,blue and white lights will flash 2~3 times, which indicate that the

DMX address is right and it go in to the DMX MODE automatically. If the address is wrong the red

light will be on. New DMX address should be put in.

If the 951 are put in, red and green lights will be on.Put “0” to initialize the program. If the wrong

address is put in, the red light will be on, indicating new address should be put in. Then the system

will run in the designed mode.

Black Out mode

Press “BLACK OUT” to set the LED lights power on or power off by pressing this button.

ViSAGE VIS0495 Operating instructions

ViSAGE VIS0495 Operating instructions

ViSAGE VIS0495 Operating instructions

Related papers

Other documents