Banner A-GAGE MINI-ARRAY MAC16N-1 User manual

Banner
Brand
Banner
Model
A-GAGE MINI-ARRAY MAC16N-1
Type
User manual

This manual is also suitable for

Printed in USA 04/12 P/N 43298 rev. F
A-GAGE
®
MINI-ARRAY
®
Measuring Light Screen System (MAC Series Controllers)
Instruction Manual
Features
Controller Models MAC-1, MACN-1, MACP-1,
MACV-1, MACI-1, MAC16N-1, MAC16P-1
(See Section 1.1 for additional, model-specific features)
• MeasuringLightScreensystemforinspectionandprofiling
applications.
• ModularsystemwithcompactcontrollerandavarietyofBMEL/
BMRLseriesMINI-ARRAYemittersandreceivers.
• Sensorsavailablewitheither9.5mm(3/8")or19.1mm(3/4")
beamspacingandwitharraylengthsfrom6"to4'
(in6"increments),plus5'and6'models.
• Controllerisprogrammableforanyoneortwooften
measurementmodes(dependingonmodel)andanyoneoffour
scanningmodes,usingacomputerrunningWindows
®
.XP,
Vista, or 7 and
the Banner-suppliedsoftware
• Softwareisalsosuppliedfordisplayoferroranalysis(via
controllerself-diagnostics)andforsensoralignment.
• Systemstatus,includingalignment,isdisplayedviaLED
indicatorsonthecontrollerandonthereceivers.
• Controllermaybeprogrammedforblankingtoignoreactivityin
oneortwofieldsalongthelengthofthearray.
• Programmablehysteresisatthehighand/orlowlimitofeach
measurementareaprovidessmoothingofoutputresponse;
alsoprogrammablefornumberofconsecutivescansbeforean
outputupdate.
• Separategateinput(e.g.,fromapresencesensor)allowscontrol
ofscaninitiation.
•SupportsserialcommunicationwithacomputerorPLCviaRS-
232Cinterface;enablesacomputerorPLCtoprocessscandata
and/orinitiatescans;serialdatamaybeeitherASCIIorbinary.
WARNING . . .
Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
ThesesensorsdoNOTincludetheself-checkingredundantcircuitrynecessarytoallowtheiruseinpersonnelsafetyapplications.A
sensorfailureormalfunctioncancauseeitheranenergizedorde-energizedsensoroutputcondition.ConsultyourcurrentBanner
SafetyProductswhichmeetOSHA,ANSIandIECstandardsforpersonnelprotection.
!
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
1. System Overview ........................................ page 3
1.1 SystemFeatures ............................................... 4
1.2 SystemComponents ............................................ 7
2. Specifications ........................................... page 9
2.1 EmitterandReceiverSpecifications................................. 9
2.2 EmitterandReceiverDimensions ................................. 10
2.3 ControllerSpecifications ......................................... 11
2.4 ControllerDimensions .......................................... 12
3. Installation and Mechanical Alignment
........................ page 13
3.1 EmitterandReceiverMounting.................................... 13
3.2 ControllerMounting ............................................ 14
3.3 EmitterandReceiverHookups .................................... 14
3.4 ControllerWiringandOutputHookups.............................. 15
3.5 SystemPower................................................. 18
3.6 Gate
......................................................... 18
3.7 SerialCommunication........................................... 18
4. Software Installation
..................................... page 19
5. Controller Configuration
................................... page 20
5.1 CommunicationsSetup.......................................... 20
5.2 AlignmentAnalysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.3 Alignment
.................................................... 21
5.4 ParameterSetupFiles(PSFs) ..................................... 22
5.5 CreatingNewParameterSetupFiles(PSFs) .......................... 25
5.5.1 AnalysisModeAssignment.................................. 25
5.5.2 OutputProgramming ...................................... 25
5.5.3 AnalysisModeSelection.................................... 28
5.5.4 BlankingSpecifications..................................... 29
5.5.5 ScanningMethods ........................................ 31
5.5.6 ControlModeSelection .................................... 32
5.6 SerialCommunication........................................... 32
5.7 PSFAssignmentandStorage ..................................... 33
6. System Operation
........................................ page 35
6.1 SensorOperatingStatusIndicators ................................ 35
6.2 ControllerOperatingStatusIndicators .............................. 36
6.3 DiagnosticsProgram ........................................... 37
Appendix ............................................. page 39
HostModeCommand.................................................... 39
SerialDataFormat ...................................................... 39
Contents
Table of Contents
P/N 43298 rev. E 3
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
System Overview
TheBannerA-GAGE
®
MINI-ARRAYmeasuringlightscreenisidealforapplications
suchason-the-flyproductsizingandprofiling,edge-guidingandcenter-guiding,loop
tensioningcontrol,holedetection,partscounting,dieejectionverification,andsimilar
uses.
AtypicalMINI-ARRAYSystemconsistsoffivecomponents:
•aControllermodule,
•anemitterandcorrespondingreceiver,and
•twointerconnectingcables.
Sensorsareavailableinarraylengthsfrom6"to4'(in6"increments),plus5'and6'
arraymodels,aslistedonpage7.Sensorsareavailablewitheither9.5mm(3/8")or
19.1mm(3/4")beamspacing,whichtranslatestoeither32or16beamsperfootof
arraylength.Sensorswith3/8"beamspacinghaveasensingrangeofupto6m(20').
Sensorswith3/4"beamspacinghaveasensingrangeofupto17m(55');5'and6'
arrayshaveshorterrange(seeSpecifications).
Box Profiling
Paint Booth
Profiling
Edge Guiding
Inspection Applications
Figure 1-1. Typical MINI-ARRAY Applications
1. System Overview
4 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
System Overview
1.1 System Features
Built-infeaturessimplifytheoperationoftheA-GAGEMINI-ARRAYsystem.
Programmablebeamblankingaccommodatesmachinecomponentsorotherfixtures
thatmustremaininormovethroughthelightscreen.Blankingissetbyusingthe
includedconfigurationsoftware.SeeSection5.5.4formoreinformation.
Built-indiagnosticprogrammingandeasy-to-seeindicatorsonthesensorsandthe
controlmodulemakealignmentandtroubleshootingeasy(Figure1-2).Theemitter
hasaredLEDthatsignalsproperoperation.ThereceiverhasthreebrightLEDs:green
signalsthatthesensorsareproperlyaligned;yellowsignalsmarginalalignment;and
redsignalsmisalignmentorablockedcondition.Thecontrolmodulehassevenstatus
indicators:5redLEDssignalwhenoutputsareconducting(seeSection3formore
information),Alarmoutputconducting,andgatesignalreceived;agreenLEDsignals
thatthesensorsareproperlyaligned.DIAG1,2,and3LEDsindicatesystemstatus.A
keytothediagnosticscodesisprintedonthesideofthecontrolmoduleforsimplified
troubleshooting(seeSection6.3).
TheMINI-ARRAYSystemprovidesawideselectionofsensingandoutputoptions,
including:measurement(“scananalysis”)modesandscanningmethodsthatcan
determinethetargetobject’slocation,overallsize,totalheightortotalwidth.Scanning
maybecontinuousorcontrolledbyahostprocesscontrolleroragatesensor.Some
models(MAC1,MACP,MACN)supportRS-485,whereupto15systemsmaybe
networked.
Figure 1-2. A-GAGE MINI-ARRAY System features
Emitter
DIN-Rail-Mountable Control Module
Receiver
MINI-ARRAY
CONTROLLER
2 - TX
3 - RX
5 - COM
RS-232
RS-232
MAC-1
OUT 1
ALARM
GATE
DIAG 1
DIAG 2
DIAG 3
ALIGN
POWER
Red Discrete
Output #1 LED
Red
Operational
LED
Green Alignment LED
Red Blocked LED
Yellow Marginal
Alignment LED
Red Alarm
(Discrete Output #2) LED
Red Gate LED
Green Align LED
RS-232 Port
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
15
30V
150mA
Max.
ALARM
500mA
Max
OUT 1
WH BK BU
5 Wires
BR-+
RS485
-+
10-30V DC
GATE
L2 L1
16-30V DC
1.2A Max.
14 13 12 11 10 9 8 7 6 5 4 3 2 1
T/RT/R DRN COM +12V F1
EMTR RCVR
P/N 43298 rev. E 5
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
System Overview
1.1.1 Model-Specific Features
Models MAC-1, MACN-1, and MACP-1
•SupportsserialcommunicationwithahostcomputerorPLCviaRS-232orRS-485
interface;enablesacomputerorPLCtoprocessscandataand/orinitiatescans;
serialdatamaybeeitherASCIIorbinary.
•Upto15controllersmaybeassignedseparateIDsandplacedonRS-485partyline.
•MAC-1:Twooutputs:onereedrelayandoneNPNtransistoroutput;eitheroutput
maybeinverted(i.e.,programmedfornormallyopenornormallyclosed).
• MACN-1 and MACP-1:Twodiscreteopen-collectorPNP(currentsourcing)orNPN
(currentsinking)transistoroutputs,dependingonmodel.
Models MACV-1 and MACI-1
•AnalogoutputnullandspancanbeadjustedviaPCinterfaceandsuppliedsoftware.
•Analogoutputsignalcanhaveeitherarisingorfallingslope.
•Analogoutputswillautomaticallyadjusttosensorlength.
•Discreteoutputisanopen-collectorNPN(currentsinking)thatcanbeusedasan
alarm,atrigger,orusedwithanAnalysisModeSelection(outputcapableofbeing
invertedinAnalysisMode).
•MACV-1: Twolinearsourcinganalogvoltageoutputs(0to10volts)andoneNPN
transistoroutput.
•MACI-1: Twolinearsinkinganalogcurrentoutputs(4to20mA)andoneNPN
transistoroutput.
Models MAC16N-1 and MAC16P-1
•Twoadditionalmeasurementmodes:
TRNmodecountsthenumberofclear-to-blockedandblocked-to-cleartransitions;
SEGmodepartitionsthearrayintoupto16regions.
•Controllerhasflexibleblankingcapabilitieswithunlimitedblankingconditions.
Blankingmaybesetautomatically(AutoBlanking)orspecifiedusingthesuppliedPC
software.
•
MAC16N-1:16discreteopen-collectorNPN(currentsinking)transistoroutputs.
• MAC16P-1:16discreteopen-collectorPNP(currentsourcing)transistoroutputs.
6 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
System Overview
1.1.2 Sensing Response
Sensingresponseisafunctionofthenumberofbeamsinterrogated(i.e.,steps)per
scanofthearray.Thetimeperstepis55µs(0.000055seconds).Asaresult,dense
arrays(i.e.,3/8"beamspacing)yieldthehighestsensingresolution,whilearrayswith
wider(3/4")beamspacingofferfastersensingresponse.
1.1.4 Supplied System Software
Thesuppliedsoftwareprogram,usedtoconfigureeachSystemcontrolmodule,may
berunonanyPCrunningWindows
®
XP, Vista, or 7.Themenu-driven
programwalkstheuserthroughthemanyscanningandoutputoptions.Afterthe
desiredoptionsareselected,theusercansavethecombinationofselectionsina
ParameterSetupFile(PSF),andstoreitinthecontrolmodule’snon-volatilememory.
AnynumberofPSFsmaybestoredinthecomputerandrecalledasneeded.
Thesoftwarealsoprovidesalignmentanddiagnosticsroutines.AnAlignmentscreen
displaystheindividualstatusofeachbeaminthelightscreen,aswellasthetotal
numberofbeamsintheSystem,andtotalsofbeamsblocked,made,andblanked.
Built-insystemdiagnosticscanbeusedtoassessemitterandreceiverhardware
errors.
P/N 43298 rev. E 7
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
System Overview
1.2 System Components
1.2.1 Emitter and Receiver Models
Figure 1-3. MINI-ARRAY system components
Quick-Disconnect
Cables
DIN-Rail-Mountable
Control Module
User-Supplied PC
Configure and monitor the System
with the supplied software and
a PC-compatible computer (see
Section 1.1.4).
Emitter Receiver
1.2.2 Controller-to-Sensor Cables
2requiredpersystem
19.1 mm (3/4") beam spacing – 16 beams/foot
Emitter / Receiver
Models
Array Length
Total
Beams
BMEL616A / BMRL616A
133mm(5.25") 8
BMEL1216A / BMRL1216A
286mm(11.25") 16
BMEL1816A / BMRL1816A
438mm(17.25") 24
BMEL2416A / BMRL2416A
591mm(23.25") 32
BMEL3016A / BMRL3016A
743mm(29.25") 40
BMEL3616A / BMRL3616A
895mm(35.25") 48
BMEL4216A / BMRL4216A
1048mm(41.25") 56
BMEL4816A / BMRL4816A
1200mm(47.25") 64
BMEL6016A / BMRL6016A
1505mm(59.25") 80
BMEL7216A / BMRL7216A
1810mm(71.25") 96
9.5 mm (3/8") beam spacing – 32 beams/foot
BMEL632A / BMRL632A
143mm(5.62") 16
BMEL1232A / BMRL1232A
295mm(11.62") 32
BMEL1832A / BMRL1832A
448mm(17.62") 48
BMEL2432A / BMRL2432A
600mm(23.62") 64
BMEL3032A / BMRL3032A
752mm(29.62") 80
BMEL3632A / BMRL3632A
905mm(35.62") 96
BMEL4232A / BMRL4232A
1057mm(41.62") 112
BMEL4832A / BMRL4832A
1210mm(47.62") 128
BMEL6032A /BMRL6032A
1514mm(59.62") 160
BMEL7232A / BMRL7232A
1819mm(71.62") 192
Model Length QD Connector
QDC-515C
4.6m(15')
5-pinMini-style
straight
QDC-525C
7.6m(25')
QDC-550C
15.2m(50')
MAQDC-575C
22.7m(75')
MAQDC-5100C
30.3m(100')
MAQDC-5125C
37.9m(125')
MAQDC-5150C
45.5m(150')
8 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
DimensionsforallMACSeriesControllerslistedaboveare:110x100x75mm(4.3"x3.9"x3.0");seeFigure2-2.
*SeeSection5.5.3foradetaileddescriptionofavailablescananalysismodes.
System Overview
1.2.3 MINI-ARRAY MAC Series Controller Models
Controller
Model
Supply
Voltage
Inputs Output 1 Output 2
Scan
Analysis
Modes*
PSF
Parameter
Diskette
Serial
Output
MAC-1
16to30Vdc
1SensorPair
1Gate
DiscreteReedRelay
DiscreteNPN
8 43989
RS-232
and
RS-485
MACN-1
DiscreteNPN
MACP-1
DiscretePNP DiscretePNP
MACV-1
(2)Analog
0to10VdcSourcing
DiscreteNPN
RS-232
MACI-1
(2)Analog
4to20mASinking
MAC16N-1
16DiscreteNPNOutputs
10 59114
MAC16P-1
16DiscretePNPOutputs
P/N 43298 rev. E 9
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Specifications
2. Specifications
2.1 Emitter and Receiver Specifications
Emitter/Receiver Range
9.5 mm (3/8") Beam Spacing
0.6to6.1m(2to20')forsensors<4'
0.6to4.6m(2to15')forsensors>4'
NOTE:Maximumrangeisspecifiedatthe
pointwhere3xexcessgainremains.
19.1 mm (3/4") Beam Spacing
0.9to17m(3to55')forsensors<4'
0.9to14m(3to45')forsensors>4'
NOTE:Maximumrangeisspecifiedatthepoint
where3xexcessgainremains.
Minimum Object Sensitivity
9.5 mm (3/8") Beam Spacing
19.1mm(0.75")
InterlacedMode:12.7mm(0.5")*
*NOTE:Assumessensingisinmiddle
one-thirdofscanningrange.
19.1 mm (3/4") Beam Spacing
38.1mm(1.5")
InterlacedMode:25.4mm(1.0")*
*NOTE:Assumessensingisinmiddle
one-thirdofscanningrange.
Sensor Scan Time
55microsecondsperbeam,plus1millisecondprocessingtimeperscan.(Assumesstraightscan,
continuousscan,andTBB mode;seeSection5.5.5ScanningModesforfurtherinformation.)
Power Requirements
Emitter
0.10amps@12Vdc
NOTE:Maximumcurrentisfora6'sensor.
Receiver
9.5mm(3/8")beams:0.75amps@12Vdcmax.
19.1mm(3/4")beams:0.50amps@12Vdcmax.
NOTE:Maximumcurrentisfora6'sensor.
Connections
Emitterandreceiverconnecttocontrollerusingtwo5-conductorquick-disconnectcables(one
eachforemitterandreceiver),orderedseparately.SeeSection1foravailablecablelengths.
Cablesmeasure8.1mm(0.32")dia.,andareshieldedandPVC-jacketed;conductorsare20-gauge.
•UseonlyBannercables,whichincorporatea"“twistedpair”fornoiseimmunityonRS-485data
communicationlines.
•Emitterandreceivercablesmaynotexceed250'each.
Status Indicators
(See Section 6.1 for more
information)
Emitter
RedLEDlightsforproperoperation
Receiver
Green:sensorsaligned(>3xexcessgain)
Yellow:marginalalignment(1x-3xexcessgain)
Red:sensorsmisalignedorbeam(s)blocked
Environmental Rating
NEMA4,13(IECIP65)
Construction
Aluminumhousingwithblackanodizedfinish;acryliclenscover
Operating Conditions
Temperature:
-20°to70°C(-4°to158°F)
Max. rel. humidity:
95%(non-condensing)
10 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
2.2 Emitter and Receiver Dimensions
Specifications
With mounting bracket flanges “out”
Figure 2-1. Emitter and receiver mounting dimensions and defined area location
With mounting bracket flanges “in”
L2
L1
X
18.3 mm
(0.72")
2.5 mm
(0.10")
38.1 mm Square
(1.50")
10.2 mm
(0.40")
L3
X
(Distance to First
Optical Channel)
9.5 mm
(3/8")
Beam
Spacing
38.1mm
(1.50")
19.1 mm
(3/4")
Beam
Spacing
42.9mm
(1.69")
Emitter/Receiver Models
Housing Length Distance Between Bracket Holes
L1 L2 L3
BMEL6..A / BMRL6..A
201.0mm(7.9") 233.9mm(9.21") 177.0mm(6.97")
BMEL12..A / BMRL12..A
356.0mm(14.0") 389.7mm(15.35") 332.8mm(13.1")
BMEL18..A / BMRL18..A
505.0mm(19.9") 538.7mm(21.22") 481.8mm(18.97")
BMEL24..A / BMRL24..A
659.0mm(26.0") 693.2mm(27.31") 636.3mm(25.05")
BMEL30..A / BMRL30.A
810.0mm(31.9") 843.5mm(33.23") 786.6mm(30.97")
BMEL36..A / BMRL36.A
963.0mm(37.9") 997.4mm(39.29") 940.5mm(37.0")
BMEL42..A / BMRL42.A
1115.0mm(43.9") 1148.0mm(45.2") 1091.0mm(43.0")
BMEL48..A / BMRL48.A
1267.0mm(49.9") 1301.0mm(51.2") 1244.0mm(49.0")
BMEL60..A / BMRL60..A
1572.0mm(61a.9") 1606.0mm(63.2") 1549.0mm(61.0")
BMEL72..A / BMRL72..A
1877.0mm(73.9") 1910.0mm(75.2") 1853.0mm(73.0")
P/N 43298 rev. E 11
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
2.3 Controller Specifications
Specifications
Power Requirements
16to30Vdc@1.25ampsmax.(seecurrentrequirementsforsensors);
Controlleralone(withoutsensorsconnected)requires0.1amp.
Inputs
MINI-ARRAYsensorinput(5connections);emitterandreceiverwireinparalleltofive
terminals.
GATEinput:Optically-isolated,requires10to30Vdc(7.5Kinputimpedance)forgatesignal.
System Response Time
Outputsarenotactivefor5secondsaftersystempowerup.Maximumresponsetimeforthe
discreteoutputsistwoscancycles.Ascancycleincludesasensorscanplusanyserialdata
transmission.
Serialtransmission(ifactivated)followseverysensorscan.
Discrete Outputs
MAC-1:
Output1(OUT1):Reedrelaycontactrated125Vac/dcmax.,10VAmax.resistive
load(non-inductive).
Output2(ALARM):OpencollectorNPNtransistorrated30Vdcmax.,150mAmax,
short-circuitprotected(maybeconfiguredasaseconddataanalysisoutput,system
alarmoutput,orscantriggeroutputforaparallelarray).
OFF-STATELeakageCurrent:<10µA@30Vdc
ON-STATESaturationVoltage:<1Volt@10mA,<1.5Volt@150mA
MACN-1: (2)OpencollectorNPNtransistoroutputs.
MACP-1:(2)OpencollectorPNPtransistoroutputs.
Transistorrated30Vdcmax.,150mAmax,shortcircuitprotected(maybe
configuredasaseconddataanalysisoutput,systemalarmoutput,orscantrigger
outputforaparallelarray).
OFF-STATELeakageCurrent<10µA@30Vdc
ON-STATESaturationVoltage<1Volt@10mA,<1.5Volt@150mA
MACV-1/MACI-1:Alarm:OpencollectorNPNtransistorrated30Vdcmax.150mAmax,short
circuitprotected.
(maybeconfiguredasadataanalysisoutput,systemalarmoutput,orscan
triggeroutputforaparallelarray)
OFF-STATELeakageCurrent:<10µA@30Vdc
ON-STATESaturationVoltage:<1Volt@10mA,<1.5Volt@150mA
MAC16P-1:SixteenopencollectorPNPtransistoroutputs.
MAC16N-1: SixteenopencollectorNPNtransistoroutputs.
30Vdcmax,150mAmax.,shortcircuitprotected.
OFF-STATEleakagecurrent:<10µA
ON-STATESaturationVoltage:<1Volt@10mA;<1.9V@150mA
Analog Outputs
MACV-1: (2) 0-10VoltssourcingadjustableNullandSpan(20mAcurrentlimit).
MACI-1: (2)4-20mAcurrentsinkingadjustableNullandSpan(16to30Vinput).
Resolution:
SpanminusNull,dividedbythenumberofsensorchannels
Linearity:
0.1%ofFullScale
Temp. Var.:
0.01%ofFullScale/°C
Serial Data Outputs
All Models: RS-232,ASCIIorbinarydataformat.
Baudrate:9600,19.2K,or38.4K8databits,1startbit,1stopbit,evenparity.
Cleardatamaybesuppressed;headerstringmaybesuppressedinbinary
format.
MAC-1, MACN-1,
and MACP-1:
Upto15ControllersmaybegivenuniqueaddressforRS-485partyline.
Controller Programming
ViaRS-232toPC-compatiblecomputerrunningWindows
®
.XP, Vista, or 7
operatingsystemandusingBanner-suppliedsoftware(seeusermanual).
12 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Status Indicators
(See Section 6.2 for
more information)
The following status LEDs are located on the front panel:
OUTPUT1(red)(nameandfunctionvarydependingonmodel):Indicatesactiveoutput
ALARM(red):IndicatesthatOutput2or16isactive(dependingonmodel)
GATE(red):IndicatesvoltageisappliedtoGATEinput
ALIGN(green):Indicatessensoraligned(excessgain>1x)
Plus three diagnostic LEDs:
DIAG1(green):Indicatespowerisappliedtothemodule
DIAG2(red):Indicatesreceiverfailure
DIAG3(red):Indicatesemitterfailure
Sensor Scan Time
For all models:
55microsecondsperbeamplusprocessingtime.
Theprocessingtimeisdependentonthescananalysisandthenumberofactiveoutputs.
Thistimingassumesastraightscan,continuous,andTBBmode.
MAC-1, MACN-1 & MACP-1:1millisecondprocessingtime.
MACV-1 & MACI-1:
1.5millisecondsprocessingtime.
MAC16N-1 & MAC16P-1:2.3to7millisecondsprocessingtime.
Construction
Polycarbonate
Environmental Rating
NEMA1(IP20)
Operating Conditions
Temperature:
-20°to+70°C(-4°to+158°F)
Maximum Relative Humidity:95%(non-condensing)
2.4 Controller Dimensions
Figure 2-2. Control module dimensions and mounting hole locations
75.0 mm
(2.95")
60.8 mm
(2.40")
7.1 mm
(0.28")
Din mounting tab
(supplied)
Slot for screws (2)
M3.5 x 0.6 mm (2)
35.0 mm
(1.38")
Din mounting slot
100.0 mm
3.94"
85.3 mm
3.36"
7.4 mm
(0.29")
110.0 mm
(4.33")
Combo Head (Phillips/Slotted Screws
M3.5 x 0.6 mm x 14 mm (2 ) (#6 x 0.5" equivalent) (supplied)
M3.5 Washers (2) (#6 equivalent) (supplied)
M3.5 mm x 0.6 mm Nuts (2) (#6 equivalent) (supplied)
Recommended torque is
16-20 in -lbs on mounting screws
Specifications
2.3 Controller Specifications (continued)
P/N 43298 rev. E 13
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Installation and Mechanical Alignment
3.1 Emitter and Receiver Mounting
BannerMINI-ARRAYemittersandreceiversaresmall,lightweight,andeasytomount;themountingbrackets(supplied)allow±30
degreesrotation.
Fromacommonpointofreference,makemeasurementstopositiontheemitterandreceiverinthesameplanewiththeir
midpointsdirectlyoppositeeachother.MounttheemitterandreceiverbracketsusingtheM4x0.7x14mmboltsandassociated
mountinghardware(allsupplied).SeeFigure3-1.
Althoughtheinternalcircuitryoftheemitterandreceivercanwithstandheavyimpulseforces,vibrationisolatorscanbeused
insteadoftheM4boltstodampenimpulseforcesandpreventpossibledamagefromresonantvibrationoftheemitterorreceiver
assembly.TwodifferentAnti-VibrationMountingKitsareavailablefromBannerasaccessories.
Figure 3-1. MINI-ARRAY emitter and receiver mounting hardware
Emitter
or
Receiver
Mounting
Mounting
Bracket
Surface
M4
Nut (4)
Washer (2)
with Compression
Slotted Hex Head
M4 x 10 mm
Bracket
Mounting
Nut
Washer
M4 x 14 mm
Screw with Flat
Washer
Compression
Washer (4)
Torque to
12 in. lbs.
(1.3 N-m)
3. Installation and Mechanical Alignment
P/N48955consistsof4anti-vibration
mounts(M4x0.7x9.5mm)and8
M4Kepsnuts.Thesemountsaremade
fromBUNA-Nrubberandaremore
resistanttochemicalsandoils.
P/N12847consistsof4anti-vibration
mounts(M4x0.7x9.5mm)and8
M4Kepsnuts.Thesemountsaremade
fromnaturalrubber,whichareless
chemicallyresistantthanthe48955
mounts,buthaveagreatersheerforce
specathighertemperature.
14 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Installation and Mechanical Alignment
Figure 3-2. MINI-ARRAY emitter and receiver mounting bracket dimensions
Mounttheemitterandreceiverintheirmountingbrackets(showninFigure3-1),
andpositiontheredlensesofthetwounitsdirectlyfacingeachother.Theconnector
endsofbothsensorsmustpointinthesamedirection.Measurefromoneormore
referenceplanes(i.e.,thefloor)tothesamepointsontheemitterandreceiverto
verifytheirmechanicalalignment.Ifthesensorsarepositionedexactlyverticalor
exactlyhorizontal,acarpenter’slevelmaybeusefulforcheckingalignment.Extending
astraight-edgeorastringbetweenthesensorsmayhelpwithpositioning.Alsocheck
byeyeforline-of-sightalignment.Makeanynecessaryfinalmechanicaladjustments,
andhand-tightenthebrackethardware.SeeSection5forinformationonalignment
indicatorsandtheuseofthealignmentsoftwaresuppliedwiththecontroller.
Connecttheshieldedcablestotheemitterandreceiver,androutethemtothe
controllerlocation.Followthelocalwiringcodeforlow-voltagedccontrolcables.The
samecabletypeisusedforbothemitterandreceiver(twocablesrequiredpersystem).
Cutthecablestolengthaftermakingsuretheyareroutedproperly.Removecablebraid
atthecontrollerconnectionpoints(seeFigure3-4).
3.2 Controller Mounting
ThecontrollermustbeinstalledinsideanenclosurewithaNEMA(orIEC)rating
suitablefortheoperatingenvironment.
MountingdimensionsforthecontrollerareshowninFigure2-2.Thecontrolleris
suppliedwithM3.5x0.6hardwarefordirectmountingtoasurface,oritcanbe
mountedontostandard35mmDINrail.
3.3 Emitter and Receiver Hookups
Emitterandreceivercablesconnectinparalleltocontrollerterminals#4through#8.
Connectthewiresfrombothsensorcables,asfollows:
Terminal4 Brown
Terminal5 Blue
Terminal6 Bare
Terminal7 Black
Terminal8 White
Trimoffthefoilshieldandthebraidedshieldatthepointwherethewiresexitthecable
(seeFigure3-4).
The“drainwire”istheuninsulatedstranded
wirewhichrunsbetweenthebraidedshield
andthefoilshield.Removethefoilshield
andbraidedshieldatthepointwherethe
wiresexitthecable.
Figure 3-4. Emitter/receiver cable
preparation
Tr im braided shield flush
with cable
Tr im foil shield flush
with cable
Uninsulated
drain wire
Emitter or
Receiver
8.1 mm
(0.32") max.
0.5" (13 mm) radius minimum bend
71 mm
2.8"
Figure 3-3. Quick-disconnect cable
clearances
P/N 43298 rev. E 15
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Installation and Mechanical Alignment
Figure 3-5. Model MAC-1 hookup
1
+
–
+
–
10-30V dc
Gate
16-30V dc
1.2 A Max.
234
5678
9
101112131415
F1
BROWN
BLUE
DRAIN (BARE)
BLACK
WHITE
EMITTER and
RECEIVER CABLES
V– V+
RS485
500 mA
Max.
Out 1
30V
150 mA
Max.
ALARM
Power
3.4 Controller Wiring and Output Hookups
CableclearancedimensionsforthearraysareshowninFigure3-3.
Controllerconnectionsaremadeviathewiringterminalsalongthefrontsurface
ofeachmodule.Emitterandreceiverhookupsandcontrolleroutputsareshownin
Figures3-5through3-11.
3.4.1 Model MAC-1 Controller Hookup
Output 1:Controllerterminals#9and#10(OUT1)arereedrelaycontactsrated
at125Vac/dcmax.,10VAmax.resistive(i.e.,non-inductive)load.Itmaybe
programmedaseithernormallyopenornormallyclosed.
Alarm:Controllerterminal#15(Alarm)isanopen-collectorNPNtransistorswitch
ratedat30Vdcmax.,150mAmax.Itisprotectedagainstoverloadandshortcircuits.
3.4.2 Model MACP-1 Controller Hookup
Output 1:Controllerterminal#9(OUT1)isanopen-collectorPNPtransistorswitch
ratedat30Vdcmax.,150mAmax.Itisprotectedagainstoverloadandshortcircuits.
Alarm:Controllerterminal#15(ALARM)isanopen-collectorPNPtransistorswitch
ratedat30Vdcmax.,150mAmax.Itisprotectedagainstoverloadandshortcircuits.
Bothoutputsarecurrentsourcing.
Figure 3-6. Model MACP-1 hookup
1
+
–
+
–
10-30V dc
Gate
16-30V dc
1.2 A Max.
234
5678
9
101112131415
F1
BROWN
BLUE
DRAIN (BARE)
BLACK
WHITE
EMITTER and
RECEIVER CABLES
V- V+
RS485
Com
30V
150 mA
Max.
ALARM
30V
150 mA
Max.
Out
Power
V+ V+
16 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Installation and Mechanical Alignment
1
+
–
+
–
10-30V dc
Gate
16-30V dc
1.2 A Max.
234
5
678
9
10131415
F1
BROWN
BLUE
DRAIN (BARE)
BLACK
WHITE
EMITTER and
RECEIVER CABLES
V- V+
RS485
Out 1
30V
150 mA
Max.
30V
150 mA
Max.
ALARM
Power
12 11
Com
1
+
–
10-30V dc
Gate
16-30V dc
1.2 A Max.
234
5678
9
10131415
F1
BROWN
BLUE
DRAIN (BARE)
BLACK
WHITE
EMITTER and
RECEIVER CABLES
V- V+
30V
150 mA
Max.
ALARM
0-10V
10 mA
V out 2
Power
12 11
Com Com
0-10V
10 mA
Max.
V out 1
Figure 3-7. Model MACN-1 hookup
Figure 3-8. Model MACV-1 hookup
3.4.3 Model MACN-1 Controller Hookup
Output 1:Controllerterminal#9(OUT1)isanopen-collectorNPNtransistorswitch
ratedat30Vdcmax.,150mAmax.Itisprotectedagainstoverloadandshortcircuits.
Alarm:Controllerterminal#15(ALARM)isanopen-collectorNPNtransistorswitch
ratedat30Vdcmax.,150mAmax.Itisprotectedagainstoverloadandshortcircuits.
Bothoutputsarecurrentsinking.
3.4.4 Model MACV-1 Controller Hookup
Voltage outputs 1 and 2:Controllerterminals#9(Vout1)and#13(Vout2)are
analogvoltageoutputs.TheloadforanalogvoltageOutput#1shouldbetiedacross
terminals#9and#10.TheloadforanalogvoltageOutput#2shouldbetiedacross
terminals13and14.Bothswitchesareratedat10Vdcmax.,10mAmax.Both
outputsarevoltagesourcing.
Alarm:Controllerterminal#15(ALARM)isanopen-collectorNPNtransistorratedat
30Vdcmax.,150mAmax.,currentsinking.
P/N 43298 rev. E 17
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Installation and Alignment
3.4.5 Model MACI-1 Controller Hookup
Current outputs 1 and 2:Controllerterminal#9(Iout1)and#13(Iout2)areanalog
currentoutputs.TheloadforanalogcurrentOutput#1shouldbeconnectedbetween
anexternal16to30Vdcpowersupplyandterminal#9.Theloadforanalogcurrent
Output#2shouldbeconnectedbetweenanexternal16to30Vdcpowersupply
andterminal13.Theloadexternalpowersupplyreturnshouldbecommonwiththe
controllerpowersupplyreturn.Bothoutputsarecurrentsinking.
Alarm:Controllerterminal#15(ALARM)isanopen-collectorNPNtransistorratedat
30Vdcmax.,150mAmax.Itisprotectedagainstoverloadandshortcircuits.
1
+
–
10-30V dc
Gate
16-30V dc
1.2 A Max.
234
5678
9
10131415
F1
BROWN
BLUE
DRAIN (BARE)
BLACK
WHITE
EMITTER and
RECEIVER CABLES
V- V+
30V
150 mA
Max.
ALARM
Power
12 11
Com Com
4-20 mA
I out 2
4-20 mA
I out 1
3.4.6 Model MAC16P-1 Controller Hookup
Terminals#15through#30areopen-collectorPNPtransistoroutputsratedat30V
dcmax.,150mAmax.Theyareprotectedagainstoverloadandshortcircuits.The
isolatedgateinputisatpins11and12.
Controllerterminal#15(output#16)maybeusedasanoutputorasanalarm.
Wheneverthisoutputisactive,theredAlarmLEDisON.
Alloutputsarecurrentsourcing.
Figure 3-9. Model MACI-1 hookup
1
+
–
10-30V dc
Gate
16-30V dc
1.2 A Max.
234
5
678
9
101314
15 30
F1
BROWN
BLUE
DRAIN (BARE)
BLACK
WHITE
EMITTER and
RECEIVER CABLES
V- V+
Power
12 11
NC NC NC NC
through
16 Solid-state Ouputs
V+
150 mA Max each
Figure 3-10. Model MAC16P-1 hookup
18 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Figure 3-12. DB9 serial connector
3.5 System Power
Connecta16to30Vdcsourcetocontrollerterminals#1(V+)and#2(V–).Connect
agoodearthgroundtoterminal#3.Agoodearthgroundisimportantforproviding
electricalandRFnoiseimmunitytotheMINI-ARRAYSystem.Thedcpowersource
mustsupply1.25amps(worstcase)whenusingthelongest(6')sensors.See
Specifications(Section2)formoreinformation.
3.6 Gate
Connectaswitched10to30Vdcsourceasagatinginput(ifrequired)between
controllerterminal#11(+)and#12(-).Voltageistypicallyswitchedbytheopen-
collectoroutputtransistorofadcsensingdevice.
3.7 Serial Communication
RS-485 (Models MAC-1, MACP-1, and MACN-1 only)
ConnectRS-485lines(ifused)toterminals#13(+)and#14(-).
RS-232
PrepareanRS-232cableusingaDB-9maleconnectorwiththeconnectionsshownin
Figure3-12.
NOTE: DO NOT use a “null modem” RS-232 cable.
RS-232
5
23
2- TX
3- RX
5- COM
DB-9 Pin #
Function
Ground (GND)
Receive (RX)
Transmit (TX)
5
3
2
Installation and Alignment
3.4.7 Model MAC16N-1 Controller Hookup
Terminals#15through#30areopen-collectorNPNtransistoroutputsratedat
30Vdcmax.,150mAmax.Theyareprotectedagainstoverloadandshortcircuits.
Alloutputsarecurrentsinking.
Controllerterminal#15(output#16)maybeusedasanoutputorasanalarm.
Wheneverthisoutputisactive,theredAlarmLEDisON.
Figure 3-11. Model MAC16N-1 hookup
P/N 43298 rev. E 19
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
Software Installation
4. Software Installation
The Parameter Setup Software CD includes an installation program that quickly and easily loads the MINI-ARRAY configuration program into the computer.
The MINI-ARRAY configuration program requires approximately 50 MB of hard disk space. Install as follows:
1. Use the Parameter Setup Software CD included with the controller, or download (www.bannerengineering.com) per the following:
Models MAC-1, MACI-1, MACN-1, MACP-1, MACV-1: CD P/N 75877
Models MAC16N-1, MAC16P-1: CD P/N 75878
2. Insert the Software CD into the CD drive.
If the program does not auto-start, browse to your CD drive, click Setup.exe, then select START, then select
RUN.
2. The Welcome dialog box will appear. Select Next, and follow the prompts in the dialog boxes as they appear.
4. The installation program then decompresses the files. A status dialog box monitors the progress of the installation.
5. An Installation Completed dialog box appears. Select OK. Reboot your computer for the changes to take effect.
After the software is installed, a MINI-ARRAY shortcut icon is placed on your desktop. Double-click on the MINI-ARRAY icon to launch the program, then
follow the configuration and setup procedures described in Section 5 of the primary manual.
Figure 4-1. MINI-ARRAY software installation: dialog boxes
20 P/N 43298 rev. E
Banner Engineering Corp. •Minneapolis,MNU.S.A.
www.bannerengineering.com•Tel:763.544.3164
MINI-ARRAY
®
InstructionManual
ConfigurationoftheMINI-ARRAYcontrollerisaccomplishedwithaWindows
®
menu-
styleprocedure,usingtheBanner-suppliedsoftwareandaPC-compatiblecomputer
runningWindows
®
XP, Vista, or 7.Aserialdataconnectionismade
betweenthecomputerandtheDB9connectoronthecontroller(seeFigure3-12).
ParameterSetupFiles(PSF)areprogrammedconfigurationsthatcanbestoredinthe
controlmodule’snon-volatilememory.TheBannersoftwarecanstorevariousPSFsin
computerfilesforinstantcall-upofaparticularconfiguration.
TheBannersoftwarealsoprovidestwoadditionalfeatures:AnAlignmentscreenanda
Diagnosticsscreen
5.1 Communications Setup
TheMINI-ARRAYsoftwarepermitsserialcommunicationviaRS-232betweentheMAC
controllerandthePC.TheminimumconnectionstotheDB-9connectoronthe
MINI-ARRAYControllersareasfollows:
Figure 5-1. MINI-ARRAY software Option
menu
Figure 5-2. MINI-ARRAY software Main
menu
NOTE: DO NOT use a “null modem” RS-232 cable.
ConfiguretheCOMportofthePCbyfirstselectingtheOptionsmenu(seeFigure
5-1).Theprogramsupportsserialcommunicationviathe.COM1-COM20.port.
ofthecomputer.SelectOptions,thenselectSerial Port(orEnter).Selecteither
COM1orCOM2.CheckSave Settings on Exit (ifitisnotalreadychecked)tostore
theCOMportselection.
5.2 Alignment Analysis
AlignmentstatusiscontinuouslydisplayedbythegreenLEDindicatorontheReceiver
andthecontroller.Whenallunblankedbeamsareclear,andexcessgainofallbeams
ismorethan3x,thegreenalignmentindicatorswillbeON.Whentheexcessgain
ofoneormorebeamsdropstobetween3xand1x,thegreenALIGNLEDonthe
controllerwillremainON,buttheyellowLEDonthereceiverwillcomeONtoindicate
awarningofmarginalalignment.SeeSection6formoreinformationaboutsensor
alignment.
OnefeatureoftheMINI-ARRAYsoftwareisaprogramthatdisplaysthestatusof
eachbeaminthearray.Thisroutinecanbeveryhelpfulforfinalalignmentorwhen
analyzinghowtheMINI-ARRAYisviewingobjectsinthesensingarray.Tolaunchthis
program,selectAlignment...undertheMINI-ARRAYmenu(seeFigure5-2),or
presstheF3key.
Controller Configuration
5. Controller Configuration
Pin Number of DB-9 Function
2 Transmit(TX)
3 Receive(RX)
5 Ground(GND)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Banner A-GAGE MINI-ARRAY MAC16N-1 User manual

Banner
Brand
Banner
Model
A-GAGE MINI-ARRAY MAC16N-1
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents