2. Toro
  3. Anti-Scalp Roller Kit, 38in Mowers for TimeCutter Z Riding Mower

Toro Anti-Scalp Roller Kit, 38in Mowers for TimeCutter Z Riding Mower, Anti-Scalp Roller Kit, 42in Mowers for TimeCutter Z Riding Mower Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Anti-Scalp Roller Kit, 38in Mowers for TimeCutter Z Riding Mower Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
All Rights Reserved
Printed in the USA
1
2003 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Anti-Scalp Roller Kit
38 and 42 inch Mowers for TimeCutter Z Riding Mower
Model No. 106–7020 and 106–7027
Form No. 3329–343
Installation Instructions
Note: Determine the left and right sides of the machine from the normal operating position.
Loose Parts
Note: Use the chart below to identify parts for assembly.
Description Qty. Use
Gage wheel bracket, front right
Gage wheel bracket, front left
Gage wheel
Wheel bolt
Lock nut, 3/8 inch
1
1
2
2
2
Assembling the gage wheels
Bolt, 5/16 x 5/8 inch
Flange nut, 5/8 inch
6
6
Installing the gage wheel bracket, 38 inch
Bolt, 5/16 x 5/8 inch
Flange nut, 5/8 inch
4
4
Installing the gage wheel bracket, 42 inch
Assembling the Gage Wheels
1. Assemble the gage wheel and the bracket using the
wheel bolt and lock nut, 3/8 inch (Fig. 1). Use the same
hole for both brackets.
2. Repeat step one for the other bracket and wheel.
1
2
3
4
m–6670
Figure 1
Left gage wheel assembly for 42 inch deck shown
1. Gage wheel
2. Gage wheel bracket
3. Locknut
4. Wheel bolt
Adjusting the Gage Wheels
The front mower wheels are to guide the mower over
uneven ground. The front wheel height can be changed to
closely match the selected height of cut for the mower.
1. To change the height of the mower front wheels,
remove the wheel mounting bolt and change the hole
into which the wheel is mounted (Fig. 1).
2. Use the top hole for the lowest cutting height and the
bottom hole for higher cutting heights (Fig. 1).
2
Installing the Wheel Brackets
1. Stop the engine and remove the ignition key.
2. Raise the mower to the G position [4-1/2 inch
(114 mm)]. See the mower Operator’s Manual for
raising the mower.
3. Mount the brackets onto the deck using the bolts, 5/16 x
5/8 inch and flange nuts, 5/16 inch (Fig. 2 and 3).
Note: The 38 inch deck will use four bolts for the left gage
wheel bracket.
4. Lower the mower.
m–6672
3
3
4
4
1
3
4
2
Figure 2
38 inch deck shown
1. Right gage wheel 2. Left gage wheel 3. Bolt, 5/16 x 5/8 inch 4. Flange nut, 5/16 inch
3
3
4
4
1
2
m–6671
Figure 3
42 inch deck shown
1. Right gage wheel 2. Left gage wheel 3. Bolt, 5/16 x 5/8 inch 4. Flange nut, 5/16 inch
/