Winston Products SAH0P6 Operating instructions

Brand: Winston Products

Model: SAH0P6

Type: Operating instructions

This manual is also suitable for

Includes all SAH and SHH Series Models

www.winstonind.com • 800-234-5286

SAH/SHH Series

Steamers

Use & Care Manual

SAH0P3 SHH0P3 SAH0P5

SAH0P6 SHH0P6 SAH0P10

DOC050124J R14

rs 8-17-09

Built with pride by

SAHH0P3

s teamer

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

Welcome ....................................... 2

Safety ........................................... 3

Receiving Your Appliance ............. 4

Electrical Information .................... 5

Installing Auto Water Fill ............... 5

Ventilation Requirements ............. 6

Component Identification .............. 7

Controls ........................................ 8

Daily Operating Instructions ......... 9-10

Guidelines..................................... 11-12

Daily Cleaning .............................. 13-14

Troubleshooting ............................ 15-16

Circuit Diagram ............................. 17

ZAP Warranty ............................... 18

Terms & Conditions ...................... 19

Thank you for your purchase of a Winston

CVap

steamer. The benefits you will enjoy

from this appliance include energy efficiency,

durability, and simplicity of use and

maintenance.

CVap steamers are built with durable

stainless steel construction and full insulation,

and they are designed for high volume

usage. Steamers are backed by a one-year

limited warranty.

Copyright© 2009 Winston Industries LLC. All rights reserved. CVap is a registered trademark of Winston Industries LLC. The CVap logo is a trademark of Winston Industries LLC. All other company and product names

may be trademarks of their respective companies.

Internet: www.winstonind.com

Email: CustomerService@winstonind.com

Phone: 800-234-5286•502-495-5400•Fax502-495-5458

Mail: 2345CartonDrive•Louisville,KY40299USA.

Need to contact us? Choose

the most convenient method.

If you have any questions, or if anything held

in your CVap steamer doesn't meet your

satisfaction, please call our Customer Service

Center at 1-800-234-5286 or 502-495-5400,

or email us at CustomerService@winstonind.

com.

Please read this entire use & care manual

before operating your CVap

steamer. The

manual contains important safety information

and operating instructions.

table of contents

welcome

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

5. Clean appliance daily to prevent buildup of

food residue or chlorides, which can also

damage stainless steel and contaminate

food. Failure to follow proper cleaning

procedures can void your warranty.

6. Prior to using appliance for the first time,

perform the daily cleaning procedure

listed on pages 13 through 14.

7. Always allow appliance to cool before

cleaning, to avoid potential burns.

8. Do not place appliance in areas where air

temperature exceeds 100˚F (38˚C). A heat

shield may be required to prevent heat

exposure and grease laden vapors from

affecting the appliance if near heat, vapor,

or grease generating devices (such as grills,

steamers, ovens, etc.). Excess heat and

grease inside the appliance cavities may

cause electrical components to fail.

As is the case with many appliances, your

steamer should be used with caution.

Please read the following to avoid injuries.

1. Because this appliance utilizes high

voltage, it should only be installed and

serviced by a licensed electrician or

trained servicer. Attempting to install or

service the appliance yourself could result

in serious, potentially fatal injuries.

2. If an electrical shock is felt when touching

appliance, shut off power immediately

(either pull power cord or turn off circuit

breaker) and call a trained servicer for

repair. Failure to do so could result in

serious, potentially fatal injuries.

3 Always turn power switch off any time

appliance is not in use.

4. This appliance utilizes heated water vapor,

which transfers heat much more quickly

and efficiently than dry air of the same

temperature. Use caution when opening

drawers or reaching into the appliance, as

heated vapor can quickly cause burns.

Electrical Hazard

Can cause serious injury or death.

Do not attempt to install or service this appliance un-

less you are a licensed electrician or trained servicer.

Contamination Hazard

Can cause serious illness or damage

appliance.

Clean appliance daily to avoid potential contamination

hazard.

Burn Hazard

Can cause injury.

Allow 30 minutes for appliance to cool before

attempting to clean.

High Temperature and Grease Hazard

Can cause damage to appliance.

Avoid placing appliance near high heat or in grease

laden atmosphere.

Burn Hazard

Can cause serious injury.

Avoid heated vapor when opening or closing appliance.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

Door

Winston's steamer is only available hinged

left. Handle is a latch and catch style door.

Water Supply

In order to operate properly, the evaporator in

this oven must be filled with clean, potable

water. Hardware is included to connect the

oven to a copper line in your facility's water

system. If your facility has plastic or

galvanized pipes, contact a licensed plumber

to connect the water supply. Equipment

should be installed to comply with applicable

federal, state, or local plumbing codes.

Appliances with automatic water fill

systems are to be installed with adequate

backflow protection to comply with

federal, state, and local codes.

Shipping Damage

Examine equipment thoroughly for shipping

damage before, during and after unloading.

All Winston products are carefully inspected

and verified to be in good condition before

leaving our factory. The carrier delivering

your cabinet has assumed responsibility for

its safe arrival. If you notice any damage

(obvious or hidden), a claim must be made to

the carrier.

Obvious Loss or Damage

Please note any obvious loss or damage on

the freight bill or express receipt, and have

the carrier’s agent sign to acknowledge the

claim. The carrier will supply the necessary

forms. If you do not obtain and complete the

forms before the carrier's agent departs, the

carrier might refuse your damage claim.

Concealed Loss or Damage

Sometimes loss or damage is not obvious

until the product has been unpacked. If you

notice damage that was concealed by

packaging or crating, contact the carrier in

writing to notify them of the damage. The

carrier should agree to inspect the damage

within 15 days. Please retain all packing

materials. The carrier will supply an

inspection report and the required claim

forms.

receiving your appliance

Model Height with 4” Width Depth Weight

Legs (IN / MM) (IN / MM) (IN / MM) (LBS / KG)

SAH0P3 21.5/546 23.0/584 31.0/787 125/56

SHH0P3 21.5/546 23.0/584 31.0/787 125/56

SAH0P5 27.2/691 23.0/584 31.0/787 150/68

SAH0P6 61.2/1554* 23.0/584 31.0/787 Call Factory

SHH0P6 61.2/1554* 23.0/584 31.0/787 Call Factory

SAH0P10 62.9/1598* 23.0/584 31.0/787 Call Factory

*Height on assembled leg & shelf kit.

High Temperature Hazard

Can cause damage to appliance.

Fill evaporator with water prior to turning power on,

and do not allow evaporator to run dry.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

installing auto water fill

As water evaporates, any minerals in the

water will deposit on the surface of the

evaporator. These mineral deposits will inhibit

the transfer of heat. Deposits can also

degrade and damage stainless steel. The

best way to avoid mineral deposits is to clean

the appliance daily. It is also advisable to

contact your water utility for advice on

minimizing deposit buildup.

To remove the plastic tubing from the water

line connector, use your fingers to carefully

press the small brass capture ring in toward

the body of the connector. Then gently pull

the tubing out of the connector. To insert

tubing back into connector, push the tubing

fully into the connector. Once seated, try to

pull the tubing out of the connector so that

the capture ring comes out (about 1/16”

(1.6mm)) and the tubing cannot be removed.

See drawing below. Auto Water Fill Systems

must be hooked up to a potable water supply

line. Winston RECOMMENDS that the tap

valve included with the kit be attached to cold

water, copper, brass or steel line (the valve

can handle any size line from 3/8” to 1”

(9.5mm to 25.4mm)). The maximum

incoming water temperature may not

exceed 140˚F (60˚C) and the incoming

water pressure must be between 20 and

150 psi (1.4 Kgf/cm2 to 10.5 Kgf/cm2

(kilogram-force per sq. centimeter)).

CAUTION: Appliances with auto water fill

systems MUST NOT BE ALLOWED TO

RUN DRY. Heat damage to the water valve

may result.

It is the responsibility of the owner and

installer to make sure that installation

complies with all applicable local and state

plumbing codes.

High Temperature Hazard

Can cause damage to appliance.

Fill evaporator with water prior to turning power on,

and do not allow evaporator to run dry.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

The appliance is shipped with an 84”

(2134mm) power cord and plug. Refer to the

table below to determine the correct electrical

outlet. It may be necessary for a licensed

electrician to install the correct outlet or

wiring. Winston does not recommend wiring

the appliance direct.

Below is electrical information for various

models of Winston’s steamers.

electrical

Model Volts Hertz PH Amps Watts Circuit Plug

Amp Type

SAH0P3 208 60 1 23.1 4800 30 6-30P

208 60 3 20.0 4800 30 15-30P

240 60 1 20.0 4800 30 6-30P

SHH0P3 208 60 3 23.8 5700 30 15-30P

SAH0P5 208 60 1 29.8 6200 40 6-50P

208 60 3 17.2 6200 30 15-30P

240 60 1 25.8 6200 40 6-50P

SAH0P6* 208 60 1 23.1 4800 30 6-30P

208 60 3 20.0 4800 30 15-30P

240 60 1 20.0 4800 30 6-30P

SHH0P6* 208 60 3 23.8 5700 30 15-30P

SAH0P10* 208 60 1 29.8 6200 40 6-50P

208 60 3 17.2 6200 30 15-30P

240 60 1 25.8 6200 40 6-50P

*Information shown is per appliance. Stacked units will need sufficient electrical service to operate two appliances at levels shown.

Ventilation clearances - To operate properly,

the appliance will need sufficient space for air

circulation. Allow at least 2” (51mm)

clearance on all sides, particularly around

ventilation holes. Care should be taken to

prevent placing the appliance close to

anything combustible. It must be installed with

its supplied feet or legs. Appliances may be

stacked upon each other using only a

Winston supplied stacking kit and following

the instructions enclosed with the kit. Your

warranty may be void if you do not adhere to

these ventilation requirements.

ventilation requirements

Do not place appliance in an area where

ambient temperature exceeds 100°F (38˚C).

A heat shield may be required to prevent

excessive heat and grease vapors from

affecting the appliance if adjacent to heat or

grease generating devices (such as grills,

steamers, ovens). Excess heat and grease

may cause electrical components to fail.

Vent hood - Mechanical ventilation is required

for this appliance in some locations, depending

upon application. Check local health and fire

codes for requirements specific to your location.

High Temperature and Grease Hazard

Can cause property damage.

Avoid placing appliance near high heat or in grease

laden atmosphere.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

1. Hinge - supports door. Hinge is left-hand,

and is not reversible.

2. Door Gasket - seals food chamber

against heat or vapor loss.

3. Shelf Rails - hold various pan sizes.

4. Door Handle - holds door closed.

5. Evaporator Cover - protects evaporator.

Cover sits on cover support rails, and

contains an opening for manual water fill.

6. Drain Valve - opens for draining evap-

orator into floor drain during cleaning.

7. Vent Pipe - allows excess vapor to

escape from steamer.

8. Quick Disconnect Valve - (not visible in

photo) for water supply connection.

9. Power Switch - allows operator to turn

electrical power on and off. When in ON

position, steamer is in steam mode.

10. Float Switches - (not visible in photo)

trigger automatic water fill. These

stainless steel ballast-style float switches

are located under evaporator cover.

11. Fill line - (not visible in photo) indicates

level to fill water. It is necessary to do this

at first use, whether or not you are

operating with auto fill. Auto fill adds water

in short bursts to avoid thermal shock and

loss of heating efficiency. Filling evap-

orator manually with hot water before the

first cook cycle speeds steamer warm up.

12. Evaporator (not visible in photo) supplies

steam to food chamber.

13. Floor Drain Connection - for connecting

PVC pipe (provided) to floor drain.

Connection is located under steamer.

14. Bottom Cover - provides service access.

Name Plate (not in photo) identifies model

and serial numbers (important for

servicing), electrical information.

component identification

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

1. Timer Dial contains timed settings from 0

to 60 in increments of two minutes for

steaming mode. When TIMER moves to 0

minutes, buzzer sounds.

2. Power Lamp lights up to indicate that

Power Switch is in the ON position.

3. Power Switch controls electrical power to

heat system and activates heating

elements.

controls

4 5

Some details have

been omitted

for clarity.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

daily operating procedures

Prior to using appliance for the first time,

please perform the daily cleaning procedure

listed on pages 13 and 14.

Steamer must be level to operate properly. If

necessary, adjust level by turning legs.

To ensure proper operation and food safety,

steamer must be cleaned daily. Follow

cleaning instructions found on pages 13 and

14.

Please make certain evaporator has

adequate water prior to turning. Water should

be approximately 1” (2.5 cm) from overflow.

1. Prior to use, remove evaporator cover and

fill evaporator with at least 2.5 gallons

(9.5L) of potable water (max. capacity is 3

gallons (11.4L) (Figure 1).

Manually filling the steamer prior to the

day’s first use is strongly advised for

quickest warm-up. NOTE: Initial heat up

can be accelerated by using hot water for

initial fill-up. Replace evaporator cover.

During normal use automatic water fill will

add water as needed throughout the day.

This is done in short bursts to avoid

temperature loss.

NOTE: For locations with hard water, add

one tablespoon (15ml) of white vinegar or

lemon juice to water to help minimize

scale buildup. Please consider contacting

your local water authority to obtain advice

on possible water treatment to protect the

appliance. Some water supplies are high

enough in chemical content to be capable

of damaging stainless steel (if used

untreated). The evaporation process can

concentrate the chemicals in the water to

a level which could cause a damaging

reaction with the stainless steel.

2. Turn on Power Switch. This activates the

unit heaters and the auto-fill function.

3. Make sure Timer Dial is set to TIMER

OFF position.

Damage Hazard

Can cause damage to appliance.

Do not operate appliance unless it is level.

High Temperature Hazard

Can cause damage to appliance.

Fill evaporator with water prior to turning power on,

and do not allow evaporator to run dry.

Contamination Hazard

Can cause serious illness.

Clean appliance prior to rst use, to remove traces of

industrial chemicals and oils.

Contamination Hazard

Can cause serious illness or damage.

Clean appliance daily to prevent buildup of deposits or

contamination.

Figure 1

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

4. Steamer heat-up is complete when steam

exhaust is visible coming from rear vent

pipe. HINT: Heat-up can be accelerated by

using hot water for initial fill-up. Load food

into steamer and set Timer Dial to desired

setting, or leave in TIMER OFF position.

5. Stand back from door as it is being

opened to avoid burns from steam, and to

avoid accidents from temporary blinding

due to steam or fogging of glasses. When

buzzer sounds at the end of timer cycle,

turn the Timer Dial to TIMER OFF

position.

6. When the water level begins to run low,

the automatic water fill will add water to

the fill line in the evaporator.

Burn Hazard

Can cause serious injury.

Use caution when opening door on hot appliance.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

Product Cook Time Cook Time

Minutes Minutes

Full Load Single Pan

Chubs - Frozen

BBQ Beef (frozen 5-lb chub) 60-70 25-30

2-pan: (20-lbs.), 1-pan: 5-lbs.

Beef Chili (frozen 5-lb chub) 65-70 30-35

2-pan: 20-lbs., 1-pan: 5-lbs.

Beef Stew (frozen 5-lb chub) 60-70 25-30

2-pan: 20-lbs., 1-pan: 5-lbs.

Tomato Bisque (frozen 5-lb chub) 40-45 20-25

2-pan: 20-lbs., 1-pan: 5-lbs.

Miscellaneous

Hot Dogs 6 to 1 – 2-pan: 110 dogs 7-9

Smoked Sausage 15-20

2-pan: 48 sausages

Bratwurst 14-16 9-12

3-pan: 90 brats, 1-pan: 30 brats

Potstickers (chicken & veg, frozen) 20-25 18-20

3-pan: 135 dumplings ea., 1-pan: 45

Starches

New Potatoes (skin on, halved) 20-25 14-16

3-pan: 27-lbs., 1-pan: 10-lbs.

New Potatoes (skin on, whole) 25-28 18-20

3-pan: 24-lbs., 1-pan: 10-lbs.

Potatoes (70-ct, peeled, 1/2” diced) 16-18 10-12

3-pan: 30-lbs., 1-pan: 10-lbs.

Potatoes (70-ct, peeled, quartered) 20-25 15-20

3-pan: 30-lbs., 1-pan: 10-lbs.

Rice (Thai Jasmine) 20-25 30*

3-pan: 1.5 gals. rice, 3 gal. water

1-pan: 1 gal. rice, 2 gals. water

Rice (converted) 35-40 30

3-pan: 1.5 gals. rice, 3 gals. water

1-pan: .50 gal. rice, 1 gal. water

*These guidelines assume the use of perforated pans when appropriate. Use of solid pans can

increase steam time. Use of catch pan is advised when steaming crabs, clams, lobster, or other

high-protein products.

Steam time may be affected by several factors. Cook times may need to be adjusted in order to

achieve the taste, texture, and temperature preferences of the consumer. Steam times based on

SHH model.

**4” (102mm) hotel pan

Steam Time Guidelines

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

Product Cook Time Cook Time

Minutes Minutes

Full Load Single Pan

Vegetables

Asparagus (fresh) 5 (al dente) 2-3

3-pan: (6-lbs.) 8 (soft) 5-6

Broccoli Florettes (fresh) 6-7 (al dente) 4-5

3-pan: 9-lbs., 1-pan: 3-lbs. 8-9 (soft)

Broccoli Florettes (frozen) 12-14 6-8

3-pan: 12-lbs.

Carrots, Baby (fresh) 13 (al dente) 10 (al dente)

3-pan: 15-lbs., 1-pan: 4-lbs. 20 (well done) 15 (well done)

Cauliflower (fresh) 10-12 (al dente) 6-7 (al dente)

3-pan: 12-lbs., 1-pan: 4-lbs. 12-14 (well done) 9-10 (well done)

Corn (cobettes) 18-20 12-15

3-pan: 72 cobs., 1-pan: 24 cobs.

Green Beans (whole, frozen) 15-17 7-9

3-pan: 12-lbs., 1-pan: 4-lbs.

Mixed Vegetables (frozen) 14-16 6-8

3-pan: 15-lbs., 1-pan: 5-lbs.

Peas (frozen) 15-17 7-9

3-pan: 5-lbs., 1-pan: 5-lbs.

Snow Peas (fresh) 5-7 (al dente) 3-4

3-pan: 10-lbs., 1-pan: 3.3-lbs. 9-10 (well done)

Spinach (fresh) 4-5 2-2.5

3-pan: 4.5-lbs., 1-pan: 1.5-lbs.

Zucchini (fresh) 7-9 3-4

3-pan: 12-lbs., 1-pan: 4-lbs.

Seafood

Clams (fresh) 6-8

2-pan: 150 clams

Shrimp (P&E, frozen) 6-8

2-pan: 8-lbs., 1-pan: not tested

Snow Crab Clusters (frozen) 15-20

Full load: 1-pan: 10.5-lbs., or 30 legs-each

3-pan: 30-lbs., 1-pan: 10-lbs.

*These guidelines assume the use of perforated pans when appropriate. Use of solid pans

may increase steam time. Use of catch pan is advised when steaming crabs, clams, lobster,

or other high-protein products.

Steam time may be affected by several factors. Times may need to be adjusted in order to

achieve the taste, texture, and temperature preferences of the consumer. Steam times

based on SHH model.

Steam Time Guidelines

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

Required Cleaning Accessories & Supplies

• Panfordrainingevaporator

• Foodgradegermicidaldetergent

• Descalingagent(ScaleKleen™)

(available through Winston Customer

Service 1-800-234-5286)

This appliance utilizes high voltage

electrical systems, high temperature

heating systems, and hot water vapor. If

used improperly, any of these hazards are

capable of causing serious injury or

death. To avoid the potential for an

accident, please have appliance installed

by a licensed electrician, and serviced

only by trained servicers. Please make

this page available to the servicer.

If an electrical shock is felt during

operation or cleaning, unplug appliance

and have it serviced before placing back

into service.

Ensure safe operation by cleaning

appliance daily. Failure to do so can allow

harmful deposits to develop, increasing

the potential for food contamination, and

endangering your customers.

daily cleaning

Clean evaporator daily to prevent chlorides

(salts) from accumulating. Chlorides can

cause the evaporator tank to corrode, to the

extent that leaks can occur. Leaks caused by

corrosion, which is caused by a failure to

clean daily, are not covered under the

manufacturer's warranty.

Prior to using appliance for the first time,

perform the daily cleaning procedure listed on

the following page.

Electrical Hazard

Can cause serious injury or death.

Disconnect appliance and contact licensed electrician

or trained servicer.

Contamination Hazard

Can cause serious illness.

Clean appliance prior to rst use, to remove traces of

industrial chemicals and oils.

Corrosion Hazard

Can cause damage to appliance.

Clean appliance daily to avoid potential corrosion

damage.

Contamination Hazard

Can cause serious illness or damage to

appliance.

Clean appliance daily to avoid potential contamination

hazard.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

daily cleaning procedure

Before each cleaning procedure, disconnect

appliance from its electrical power source and

allow to cool for at least one half hour.

1. Check appliance to see if it is level. Adjust

legs if necessary.

2. Open red drain valve. Allow water from

evaporator to drain into floor drain.

Do not position tubes or hoses running to

floor drain in walkways or kitchen traffic

areas. Tubes or hoses can create a

tripping or slipping hazard.

2. Remove and clean evaporator cover.

3. Spray food chamber and evaporator with

a food grade germicidal detergent.

4. Wipe inside surfaces to remove all

moisture and food deposits.

5. Inspect floats, float steams, and

evaporator tank for scale build-up

(typically a whitish, chalky substance). The

steel surfaces should be cleaned daily and

kept clean. If scale is present, apply

descaling agent. Read and follow ALL

warnings and directions on descaling

agent package.

6. Clean gaskets by wiping down with a

damp towel.

NOTE: Schedule to replace door gasket

twice a year.

7. Check the drain trough's overflow tube for

debris. Clean with pipe cleaner.

8. Rinse all inside surfaces, including

evaporator, and dry with clean towel.

9. Close red drain valve.

10. Leave door open overnight to facilitate

proper drying.

11. Using a phillips screwdriver, check screws

on door handle. Tighten if necessary.

12. Reconnect appliance to electrical power

and make ready for use.

Burn Hazard

Can cause injury.

Allow 30 minutes for appliance to cool before

attempting to clean.

Accident Hazard

Can cause injury.

Avoid placing drainage tubes or hoses in foot trafc

areas.

Electrical Hazard

Can cause serious personal injury or

damage to appliance.

Avoid spraying appliance exterior or controls with

water.

Clean all scale deposits

intankandonoats.

Checkoverow

tube for debris.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

We know how frustrating and costly it can be

when a critical piece of equipment is down for

repairs. It is our goal to minimize service

disruptions, to get you back up and operating

in the shortest time possible.

We carefully analyze all service calls. This

analysis helps us to improve our

manufacturing processes, and reduces

product service issues. Generally speaking,

most equipment failures can be attributed to

the following three causes:

• Faultyuseandcarepractices.

• Electricalsupplyproblems.

• Equipmentfaults.

Please refer to the Troubleshooting Chart on

the next page for common problems and

solutions. If the problem you're experiencing

isn't listed, or if the standard solution fails to

troubleshooting

resolve your problem, you will need a

qualified servicer to diagnose and repair the

problem.

If your equipment is still under warranty, or

you are uncertain whether or not warranty is

still in place, please call Winston Customer

Service at 1-800-234-5286 (or

502-495-5400). Our friendly staff will help you

verify coverage, and if under warranty, will

arrange for a servicer to call on you.

If your equipment is no longer under warranty,

you can call our Customer Service line at

1-800-234-5286, or visit our website at www.

winstonind.com, and click the Service tab to

locate an authorized servicer near you.

In order to expedite service, please have the

complete model and serial number (found on

the appliance's identification tag) on hand

when you contact us.

For the latest parts availability, call our

Customer Service line at 1-800-234-5286 or

502-495-5400. You may also order direct at

http://www.winstonind.com/buy_parts

Please have the following information on hand when contacting Winston Industries

regarding product service.

1. Model _____________________Serial # _____________________________________

(located on name plate)

2. Your name ______________________________________________________________

3. Company name _________________________________________________________

4. Company address _______________________________________________________

_______________________________________________________________________

5. Company phone _________________________________________________________

6. Type of problem _________________________________________________________

_______________________________________________________________________

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

troubleshooting

FAULT CORRECTION

A. Building circuit breaker tripped or fuse blown .............................. Reset or replace

B. Power cord not plugged in ........................................................... Plug in

C. Faulty power cord ........................................................................ Call factory

D. Faulty power switch ..................................................................... Call factory

E. Faulty power lamp ........................................................................ Call factory

F. Evaporator empty or low .............................................................. Add water, see pg.9

G. Automatic water-fill faulty ............................................................. See pg 14, item #7,

or call factory

H. Water source connected improperly ............................................ Call factory

I. Drain valve defective .................................................................... Call factory

J. Incorrect cook time selected ........................................................ See pg. 11-12

K. Leaking door gasket at sides or top ............................................. Call factory

L. Food or scale build-up ................................................................. See pgs. 14

M. Screw loose on Timer knob ......................................................... Tighten screw

N. Screws loosened from door latch and catch ................................ Tighten screws

O. Injury or accident, call Manufacturer ............................................ Administer first aid.

If necessary, call 911

for emergency

assistance. Then

contact Winston at

1-800-234-5286.

TROUBLE FAULT CODE

Power lamp outage ............................................................................................A B C D E

Timer dial not responding correctly ....................................................................M

Leaking water - back ..........................................................................................G H

Leaking water - front

..........................................................................................I K

Food not properly cooked ..................................................................................F J

Cooking time too long

........................................................................................J

Offensive odors ..................................................................................................L

Steam escaping from door .................................................................................K N

Evaporator overflowing

.......................................................................................G

Injury or accident ................................................................................................O

Read pages 13 and 14 thoroughly. If proper cleaning procedures are not followed, it

could void your warranty.

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

circuit diagram - SAH/SHH series

Includes all SAH and SHH Series Models

www.winstonind.com • 800-234-5286

s teamer

ZAP WARRANTY AGREEMENT

This warranty agreement applies to commercial equipment, equipment service parts, and safety parts (collectively, “Products”) manufactured by

Winston Industries, LLC (“Winston”) and its corporate predecessors and is extended to any purchaser, lessee or successor purchaser

(“Purchaser”).

NEW EQUIPMENT

Any part of a new appliance, except gaskets, hoses, lamps, power cords, fryer baskets, glass panels, and evaporators which proves to be

defective in material or workmanship within one (1) year from the date of delivery to original end-user purchaser or 18 months from the date of

manufacture, whichever comes first, will be repaired or replaced (at Winston's option) free of charge.

REPLACEMENT PARTS

Any appliance replacement part except gaskets, hoses, lamps, power cords, fryer baskets, glass panels, batteries, and evaporators which proves

to be defective in material or workmanship within one (1) year from the date of original installation will be repaired or replaced free of charge.

LABOR, TRAVEL, TRANSPORTATION

The warranty for new equipment covers the repair or replacement (at Winston's option) of the defective part(s), delivery of the replacement

part(s), labor charges for the removal and installation of replacement part(s) for one (1) year from the start of the warranty period. This warranty

includes travel time not to exceed two hours and mileage not to exceed 50 miles (100 miles round trip).

The warranty for replacement parts covers the repair or replacement (at Winston's option) of the defective part(s) and does not include any labor

charges for the removal and installation of any part(s), travel, transportation or other expenses incidental to the repair or replacement of part(s).

The warranty does not cover: gaskets, hoses, lamps, power cords, fryer baskets, glass panels, evaporators, software, corrosion of stainless steel,

normal maintenance, lubrication, cleaning or descaling, programming or adjusting temperatures, calibration, tightening of fasteners or plumbing

connections, appliances with removed or altered identification tags, damage resulting from delivery of the appliance, customer mishandling or

abuse, or no problem found.

THE USE OF POOR QUALITY WATER WILL VOID PRODUCT WARRANTIES. See Product Use and Care Manual for water quality

recommendations.

PROPER INSTALLATION IS THE RESPONSIBILITY OF THE PURCHASER, AND IS NOT COVERED BY THIS WARRANTY. PRODUCTS MUST

NOT BE INSTALLED IN LOCATIONS EXPOSING THEM TO EXCESSIVE HEAT SOURCES, AMBIENT TEMPERATURES ABOVE 100˚F, OR

CONTAMINATES DETRIMENTAL TO THE APPLIANCE COMPONENTS (SUCH AS CAUSTIC SOLUTIONS, HIGH MOISTURE, WATER OR

GREASE LADEN VAPORS NEAR ELECTRONIC COMPONENTS, ETC.).

As a condition to the application of this warranty, Purchaser will operate, clean and maintain Products in accordance with use and care

instructions, warnings, manuals and any other notices and/or instructions from Winston which may be with or on Products or sent separately; will

notify Winston of resale, removal or retirement of Products; will notify Winston immediately of any accident or injury arising out of use of Products

and cooperate with Winston in the investigation of any such accident or injury; will maintain registration with Winston of location and serial number

of Products while in Purchaser's control and use; will require all personnel operating Products to become thoroughly familiar with use and care

instructions and all other notices and/or instructions before such personnel operate Products; will thoroughly train all personnel operating Products

to follow all instructions contained on or in all Safety Labels and use and care instructions; will immediately affix Safety Labels and put into use

the use and care instructions; will immediately use, according to instructions, Safety Parts supplied by Winston; will install Equipment Service

Parts in accordance with Winston's written instructions; will utilize only Winston manufactured replacement parts and make no changes or

alterations to Products, except as approved or instructed in writing by Winston; and will when requested by Winston, cooperate with Winston in

the prevention of injuries from Purchaser's use of Products.

PURCHASER'S SOLE AND EXCLUSIVE REMEDY AGAINST WINSTON SHALL BE FOR THE REPAIR OR REPLACEMENT OF DEFECTIVE

PARTS AS PROVIDED HEREIN. THE TOTAL LIABILITY OF WINSTON WITH RESPECT TO ITS PRODUCTS, WHETHER UNDER WARRANTY

OR OTHERWISE, SHALL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCTS AND THE LABOR AND TRAVEL TO REPLACE THE

PRODUCTS OR ANY PART THEREOF. WINSTON SHALL NOT BE LIABLE TO THE PURCHASER OR OTHERS FOR ANY DIRECT, INDIRECT,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS RESULTING FROM ANY CAUSE WHATSOEVER,

INCLUDING BUT NOT LIMITED TO, DEFECTIVE WORKMANSHIP, MATERIALS OR ANY ERROR OR OMISSION OF WINSTON.

WINSTON EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY

OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY OF MERCHANTABILITY.

For warranty inquiries and customer specific warranties, call Winston Customer Service at 1-800-234-5286 or 502-495-5400.

4272V089 rev7 5/1/07

Prices subject to change without notice.

F.O.B. Louisville, KY, USA

(800) 234-5286 or (502) 495-5400 Fax (502) 495-5458

www.winstonind.com

All sales subject to Company’s Terms and Conditions

Winston Products Company

2345 Carton Drive

Louisville, KY 40299

ZAP zero accidents program

www.winstonind.com • 800-234-5286

s teamer

Includes all SAH and SHH Series Models

www.winstonind.com • 800-234-5286

Prices subject to change without notice.

F.O.B. Louisville, KY, USA

(800) 234-5286 or (502) 495-5400 Fax (502) 495-5458

www.winstonind.com

All sales subject to Company’s Terms and Conditions

Winston Products Company

2345 Carton Drive

Louisville, KY 40299

TERMS AND CONDITIONS OF SALE

In consideration of the mutual benefits hereby to be derived, Winston Industries, LLC (“Winston”) and any purchaser, lessee or successive purchaser (“Purchaser”), of Winston

Commercial Equipment, Equipment Service Parts, and Safety Parts (collectively “Products”) agree that:

1. Terms of sale for Products are net 25 (payment must be received within 25 days from invoice date). Prices are subject to change without notice. Purchaser agrees to pay all costs

of collection of past due accounts, including reasonable attorney’s fees. All claims must be made within five (5) days of receipt of goods or claim will not be allowed. All goods are

shipped at Purchaser’s risk. Confirmed orders may not be cancelled or delayed without written permission from Winston. Cancelled or delayed orders may be subject to a 20%

inventory adjustment/warehousing fee. Delayed orders will be invoiced on the confirmed ship date. Products may not be returned without written permission from Winston as

described in paragraph #6 below. Orders placed prior to a price increase, which are due to ship after the increase, may be charged at the new price.

2. An order will not be effective until accepted by an authorized representative at Winston's home office. Unless otherwise specified in writing (a) delivery will be made F.O.B.

Louisville, Kentucky and risk of loss or damage shall pass to Purchaser upon delivery to the carrier, and (b) the method or agency of transportation and routing will be selected by

Winston. Winston reserves the right to ship freight collect.

3. Winston shall not be liable for any delay in performance due to fire, explosion, casualty, strike or other labor difficulties, shortage of utility facility, delay to transportation,

breakdown or accident, compliance with other action to carry out the intent or purpose of any law or regulation, or any cause, whether similar or dissimilar, beyond Winston’s

reasonable control and Winston shall have such additional time for performance as may be reasonably necessary under the circumstances and the right to apportion its production

among its customers in such a manner as it may deem equitable.

4. Purchaser agrees to indemnify and hold Winston harmless from any loss, cost or expense, including cost of defense, and reasonable attorney’s fees, incurred by Winston, arising

from or related to (1) Purchaser’s use or sale of Products, including, but not limited to, Purchaser’s failure to warn Purchaser’s workers and others of hazards involving the Products;

Purchaser’s failure to provide copy of Terms and Conditions at time of sale of Products to others; Purchaser’s failure to instruct Purchaser’s workers and others in how to safely use

the Products in compliance with the Use and Care Manual; and Purchaser’s failure to provide safe working conditions and proper safety clothing and gear with respect to the

Products, and (2) non-compliance with these Terms and Conditions, or both.

5. Purchaser shall pay, in addition to the price hereunder, as a separate item, any taxes which Winston may be required to pay or collect under existing or future laws with respect to

the sale, delivery, transportation, or use of any Product sold hereunder including all taxes, however designated, upon or measured by amounts paid to Winston by Purchaser

hereunder, except net income tax.

6. Products may not be returned by Purchaser except by prior written agreement with Winston. Returns without prior authorization, as indicated by an RA number applied to the

returned packaging, will be refused. All returned Products are subject to inspection by Winston and a 20% restocking charge ($30 minimum), which may be reduced if replacement

Product is ordered, plus any other costs necessary to restore the Products to new condition. The Products must be returned to the Winston factory freight prepaid, in new condition,

and in the original packaging. Winston reserves the sole right to determine the amount of credit to be issued on any Products returned for credit. Only standard, currently

manufactured Winston Products may be considered for return and credit. No returns will be accepted on modified or special order Products (built to a Purchaser’s specifications),

used Products, or on Products older than 90 days from the original date of shipment.

7. Acceptance is expressly limited to the Terms and Conditions set forth herein and any additional or different terms proposed by Purchaser are rejected unless expressly assented

to in writing. In the event during the course of dealing, Winston signs or otherwise accepts any documents or forms submitted by Purchaser containing any Terms or Conditions

contrary to or in addition to those of Winston set forth herein, such documents and forms shall be deemed to have been used for the mere convenience of Purchaser in the conduct

of its internal business affairs and not for the purpose of varying the Terms and Conditions of this order. This order including these Terms and Conditions shall constitute entirely the

Terms and Conditions between the parties with respect to the transaction covered hereby and to all subsequent transactions for Products obtained from Winston, and no waiver,

alteration or modification shall be binding on Winston unless in writing and signed by an authorized officer of Winston at its home office.

8. Purchaser's sole warranty is the Zero Accident Program (ZAP) Warranty Agreement on products manufactured by Winston in effect at the time of the sale.

OTHER THAN THE ZAP WARRANTY AGREEMENT, WINSTON MAKES NO WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, CONCERNING THE

PRODUCTS. WINSTON EXPRESSLY EXCLUDES ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE TOTAL LIABILITY

OF WINSTON WITH RESPECT TO ANY PRODUCT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE THEREOF, AND LABOR TO REPLACE. WINSTON SHALL IN NO

EVENT BE LIABLE TO PURCHASER OR OTHERS FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS

RESULTING FROM ANY CAUSE WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, DEFECTIVE WORKMANSHIP, MATERIALS OR ANY ERROR OR OMISSION OF

WINSTON.

9. Winston shall not be liable for claims of patent infringement against Purchaser or Purchaser's loss of the right to use the Product.

10. ARBITRATION: Any controversy or claim arising out of or relating to this Order, or the breach thereof, shall be settled by binding arbitration in accordance with the Commercial

Arbitration Rules of the American Arbitration Association, except that any arbitration hearing shall be held in Louisville, Kentucky. Judgment upon the award rendered by the

arbitrator(s) may be entered in any court having jurisdiction thereof. Any application for review of an arbitration award shall be allowed only to the extent required by Kentucky law

and shall be brought in an appropriate court in the Thirteenth Judicial Circuit or District of Kentucky, or in the United States District Court for the Western District of Kentucky.

11. GOVERNING LAW: This Order and the rights, duties and legal relations of the parties, and any arbitration are governed by and construed under Kentucky laws.

12. The products sold hereunder are produced in compliance with the Fair Labor Standards Act.

4272X833 rev10 2/9/05

terms & conditions

s teamer