Grandstream GXV3610 v2 series User manual

GXV3610_HD/FHD v2 User Manual www.grandstream.com

Firmware Version 1.0.3.14 http://esupport.grandstream.com

Grandstream Networks, Inc.

GXV3610_HD/GXV3610_FHD v2

Day/Night Fixed Dome HD IP Camera

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 2 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

This page intentionally left blank

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 3 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

TABLE OF CONTENTS

GXV3610_HD/FHD v2 User Manual

WELCOME.................................................................................................................................................... 5

SAFETY COMPLIANCES ............................................................................................................................ 6

FCC CAUTION .......................................................................................................................................... 7

RF EXPOSURE INFORMATION (SAR) .................................................................................................... 7

WARRANTY ................................................................................................................................................. 8

CONNECT YOUR GXV3610_HD/FHD V2 ................................................................................................... 9

EQUIPMENT PACKAGE CONTENTS ................................................................................................................. 9

CONNECTING THE GXV3610_HD/FHD V2 ................................................................................................. 10

PRODUCT OVERVIEW .............................................................................................................................. 11

GXV3610_HD/FHD V2 CAMERA ............................................................................................................... 11

GXV3610_HD/FHD V2 SPECIFICATIONS ................................................................................................... 12

INSTALLATION GUIDE ............................................................................................................................. 13

MINIMUM RECOMMENDED COMPUTER SYSTEM REQUIREMENT ..................................................................... 13

CONFIGURE THE GXV3610_HD/FHD V2 VIA WEB BROWSER ..................................................................... 13

Windows Platform: ................................................................................................................................... 14

Apple Platform: ........................................................................................................................................ 16

CONNECT TO THE CAMERA USING STATIC IP ............................................................................................... 18

GXV3610_HD/FHD V2 APPLICATION SCENARIOS ............................................................................... 19

LAN W/O INTERNET ................................................................................................................................... 19

LAN WITH INTERNET .................................................................................................................................. 20

GXV3610_HD/FHD V2 APPLICATION PERIPHERAL CONNECTION ................................................................ 21

GXV3610_HD/FHD V2 HOME WEB PAGE ............................................................................................... 23

GXV3610_HD/FHD V2 CONFIGURATION & LANGUAGE PAGE ..................................................................... 24

BASIC SETTINGS EXPLANATION ........................................................................................................... 25

SYSTEM SETTINGS PAGE ........................................................................................................................... 25

VIDEO & AUDIO SETTING PAGE .................................................................................................................. 26

OSD SETTING PAGE .................................................................................................................................. 28

CMOS SETTINGS PAGE ............................................................................................................................. 29

NETWORKING SETTING PAGE ..................................................................................................................... 31

DDNS SETTINGS PAGE ............................................................................................................................. 32

SIP SETTING PAGE .................................................................................................................................... 33

STATUS PAGE ............................................................................................................................................ 36

ADVANCED SETTINGS EXPLANATION .................................................................................................. 37

USER MANAGEMENT PAGE ......................................................................................................................... 37

MAINTENANCE PAGE .................................................................................................................................. 38

SMTP SETTING PAGE (EMAIL ALARM) ........................................................................................................ 41

FTP SETTINGS PAGE (UPLOAD ALARM) ...................................................................................................... 43

PRIVACY MASKS ........................................................................................................................................ 44

ALARM SERVER SETTINGS PAGE (UPLOAD ALARM TO SUPPORTED VMS OR HTTP SERVER) ........................ 45

TIME LAPSE PHOTOGRAPHY ....................................................................................................................... 46

MOTION DETECTION ................................................................................................................................... 47

REMOT ALARM_OUT PEERING WITH GXV3500 DECODER ........................................................................... 50

SYSLOG SETTINGS PAGE (TROUBLESHOOTING HELP) .................................................................................. 53

SOFTWARE UPGRADE ................................................................................................................................ 54

INSTRUCTIONS FOR LOCAL FIRMWARE UPGRADE USING TFTP SERVER: ........................................................ 55

CONFIGURATION FILE DOWNLOAD .............................................................................................................. 55

RESTORE FACTORY DEFAULT SETTING .............................................................................................. 56

RESET FROM WEB INTERFACE .................................................................................................................... 56

IP SURVEILLANCE FAQ ........................................................................................................................... 57

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 4 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

T

ABLE OF FIGURES

GXV3610_HD/FHD v2 U

SER MANUAL

F

IGURE 1: GXV3610_HD/FHD V2 ILLUSTRATION ....................................................................................................... 11

FIGURE 2: WINDOWS “NETWORK” SHOWING GXV3610_HD/FHD V2 AS “OTHER DEVICES” VIA UPNP...................... 14

FIGURE 3: “GS_SEARCH” RESULT PAGE OF GXV3610_HD/FHD V2 ........................................................................... 15

FIGURE 4-1: APPLE SAFARI “BONJOUR” SETTING PAGE TO DISPLAY GXV3610_HD/FHD V2 ...................................... 16

FIGURE 4-2: APPLE SAFARI “BONJOUR” SETTING PAGE TO DISPLAY GXV3610_HD/FHD V2 ...................................... 16

FIGURE 5-1: GXV3610_HD/FHD V2 WORKING IN LAN ............................................................................................. 19

FIGURE 5-2: GXV3610_HD/FHD V2 WORKING WITH GVR3550 AND/OR GSURF_PRO WITH INTERNET ..................... 20

FIGURE 6: APPLICATION PERIPHERAL CONNECTION FOR GXV3610_HD/FHD V2 ........................................................ 21

FIGURE 7: HOME PAGE OF GXV3610_HD/FHD V2 ...................................................................................................... 23

FIGURE 8: WEB LANGUAGE SWITCH ............................................................................................................................. 24

FIGURE 9: SYSTEM SETTINGS PAGE ............................................................................................................................... 25

FIGURE 10-1: VIDEO & AUDIO SETTINGS PAGE ............................................................................................................. 26

FIGURE 10-2: VIDEO & AUDIO SETTINGS PAGE ............................................................................................................. 27

FIGURE 11: OSD SETTINGS PAGE .................................................................................................................................. 28

FIGURE 12: CMOS SETTINGS PAGE ............................................................................................................................... 29

FIGURE 13: NETWORKING SETTING PAGE...................................................................................................................... 31

FIGURE 14: DDNS SETTING PAGE ................................................................................................................................. 32

FIGURE 15-1: SIP SETTING PAGE ................................................................................................................................... 33

FIGURE 15-2: SIP SETTING PAGE ................................................................................................................................... 34

FIGURE 15-3: SIP SETTING PAGE ................................................................................................................................... 35

FIGURE 16: STATUS PAGE .............................................................................................................................................. 36

FIGURE 17: USER MANAGEMENT PAGE ......................................................................................................................... 37

FIGURE 18: MAINTENANCE PAGE .................................................................................................................................. 38

FIGURE 19-1: SMTP SETTING PAGE .............................................................................................................................. 41

FIGURE 19-2: SMTP SETTING PAGE .............................................................................................................................. 42

FIGURE 20: FTP SETTING PAGE ..................................................................................................................................... 43

FIGURE 21: PRIVACY MASKS CONFIGURATION PAGE .................................................................................................... 44

FIGURE 22: ALARM HTTP SERVER SETTING PAGE ....................................................................................................... 45

FIGURE 23: TIME LAPSE PHOTOGRAPHY CONFIGURATION PAGE ................................................................................... 46

FIGURE 24-1: MOTION DETECTION CONFIGURATION PAGE ........................................................................................... 47

FIGURE 24-2: MOTION DETECTION CONFIGURATION PAGE ........................................................................................... 48

FIGURE 24-3: MOTION DETECTION SCHEDULE CONFIGURATION PAGE ......................................................................... 49

FIGURE 24-4: REMOTE ALARM_OUT IP CAMERA CONFIGURATION .............................................................................. 50

FIGURE 24-5: REMOTE ALARM_OUT PEERING GXV3500 CONFIGURATION .................................................................. 51

FIGURE 24-6: REMOTE ALARM_OUT PEERING GXV3500 ACTION OUTPUT DISPLAY ................................................... 52

FIGURE 24-7: PEERING GXV3500 DECODER ALARM_OUT CIRCUIT ............................................................................. 52

FIGURE 25: SYSLOG SETTING PAGE ............................................................................................................................... 53

FIGURE 26: FIRMWARE UPGRADE AND PROVISIONING .................................................................................................. 54

FIGURE 27: FACTORY RESET FROM WEB INTERFACE .................................................................................................... 56

T

ABLE OF TABLES

GXV3610_HD/FHD v2 U

SER MANUAL

T

ABLE 1: GXV3610_HD/FHD V2 TECHNICAL SPECIFICATIONS ................................................................................... 12

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 5 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

WELCOME

Thank you for purchasing Grand stream’s GXV3610_HD/FHD v2 Day/Night Fixed Dome High Definition

IP Camera, an innovative powerful weatherproof infrared next generation network camera. Its advanced

ISP (Image Sensor Processor) powered with state-of-the-art auto-exposure/auto-white-balance algorithm

and a high quality lens, ensures high fidelity video quality that matches digital still camera color grade in a

wide range of light environments. It features cutting edge H.264 real-time video compression with

excellent image clarity (720p for GXV3610_HD; 1080p for GXV3610_FHD) and color fidelity, industry

leading SIP/VoIP for 2-way audio and video streaming to smartphones and video phones, integrated PoE,

IR-CUT (mechanical) for day or night mode, and advanced security protection using strong encryption.

The GXV3610_HD/FHD v2 can be managed with GSurf Pro (Grand stream’s intuitive FREE video

management software that controls up to 72 cameras simultaneously), or grouped with GVR3550

Grandstream Network Video Recorder (NVR) via plug-n-play, as well as other ONVIF compliant video

management systems. It also offers an advanced and flexible HTTP API and an SDK for easy integration

with other surveillance systems. .

Designed for both indoor and outdoor environment, the GXV3610_HD/FHD v2 Day/Night Fixed Dome

HD IP camera is a new addition to the popular GXV3XXX series IP surveillance product family. It ensures

ease of use, integration and deployment, with multilingual graphical user interface, provides powerful

solution to professional surveillance applications.

Ideal application scenes for GXV3610_HD/FHD v2 are like office, store, elevator, and other small to

median sized enclosed environments, although they can also be used in a similar open space.

This manual will help you to learn how to operate and manage your GXV3610_HD/FHD v2 Day/Night

Fixed Dome HD IP camera and make the best use of it.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 6 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

SAFETY COMPLIANCES

These instructions are intended to assist users with the operation of the GXV3610_HD/FHD v2 and to

instruct on how to avoid dangerous situations or damage to the device.

Warning:

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited

Power

Source with DC 12V according to the IEC60950-1 standard. Please refer to the

technical

specifications for more

details.

Do not use a third-party power adapter or power

cord.

When the device installed on the wall or ceiling, make sure that it is firmly

attached.

Caution

：

•

Make sure that the power supply voltage is correct before using the

camera.

• Do not drop the device or expose it to physical

shock.

• Do not expose the device to temperatures outside the range of -20

o

C to 50

o

C when t

he

d

evice is in

operation.

• Do not expose the device to damp/wet conditions or high electromagnetism

radiation.

• To avoid heat accumulation, make sure that your operating environment has

proper

ventilation.

• Do not damage the warranty sticker.

A few parts (e.g. electrolytic capacitor) of the equipment shall be replaced regularly

according

to their average lifetime. The average lifetime varies from the differences between

operating

environments and usage history. Regular maintenance checks are recommended for

all

users.

Please contact your dealer for more

details.

Warning： May cause serious injury or death if any

of the warnings below are neglected.

Caution

：

Equipment may be damaged if any of

the following caution messages are neglected.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 7 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

FCC CAUTION

Any Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment. This device complies with part 15 of the

FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

— Consult the dealer or an experienced radio/TV technician for help.

RF EXPOSURE INFORMATION (SAR)

This device is designed and manufactured not to be exceeded the emission limits for exposure to

radio frequency RF energy set by the Federal Communications Commission of the United States.

The exposure standard for wireless devices employing a unit of measurement is known as the

Specific Absorption Rate (SAR), and the SAR limit set by FCC is 1.6 W/kg.

This device is complied with SAR for general population/uncontrolled exposure limits in

ANSI/IEEE C95.1-1992, and has been tested in accordance with the measurement methods and

procedures specified in OET Bulletin 65 Supplement C. This device has been tested, and meets

the FCC RF exposure guidelines when tested with the device directly contacted to the body. RF

exposure compliance with anybody-worn accessory, which contains metal, was not tested and

certified, and uses such body-worn accessory, should be avoided.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Hereby, Grandstream declares that this device is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 8 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

WARRANTY

If the GXV3610_HD/FHD v2 was purchased from a reseller, please contact the company where the device

was purchased for replacement, repair or refund.

If the device was purchased directly from Grandstream, please contact our technical support team for a

RMA (Return Materials Authorization) number before the product is returned.

Grandstream reserves the right to remedy warranty policy without prior notification.

Caution:

Changes or modifications to this product not expressly approved by Grandstream, or operation of this

product in any way other than as detailed by this User Manual, could void your manufacturer warranty.

Please do not use a different power adaptor with the GXV3610_HD/FHD v2 because this may cause

damage to the products and void the manufacturer warranty.

• This document is subject to change without notice. The latest electronic version of this user manual is

available for download at:

http://www.grandstream.com/products/surveillance/GXV3610hd/documents/GXV3610_HD/FHD

v2_usermanual_english.pdf

Reproduction or transmittal of the entire or any part, in any form or by any means, electronic or print, for

any purpose is not permitted without the express written permission of Grandstream Networks, Inc.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 9 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

CONNECT YOUR GXV3610_HD/FHD V2

Equipment Package Contents

The GXV3610_HD/FHD v2 package contains:

• GXV3610_HD/FHD v2 IP Camera

• 12V DC Universal Power Adaptor

• Ethernet Cable

• 1 Hex Key and 4 Screws and Wall Anchors

• Quick Installation Guide

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 10 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

Connecting the GXV3610_HD/FHD v2

Using the Power Adapter as power supply

 Connect the RJ-45 Ethernet cable to the NETWORK port of the GXV3610_HD/FHD v2

 Connect the other end of the RJ-45 cable to your network (switch or router or PC)

 Connect the power supply to the DC 12V power jack on the back of the GXV3610_HD/FHD v2

Using PoE as power supply

 Connect the RJ-45 Ethernet cable to the NETWORK port of GXV3610_HD/FHD v2

 Connect the other end of the RJ-45 cable to your PoE switch.

 PoE injector can be used if PoE switch is not available.

Please refer to following connection diagram to hook up the camera.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 11 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

PRODUCT OVERVIEW

GXV3610_HD/FHD v2 Camera

Figure 1: GXV3610_HD/FHD v2 Illustration

1. Microphone GXV3610_HD/FHD v2 Microphone

2. Light Sensor for IR-Cut Light Sensor for mechanical IR-Cut switching

3. Lens 1/3”CMOS (1.2M for HD/3.1M for FHD) Sensor and Lens

4. IR Light Array Infrared Light Array

5. Mounting Bracket Mounting Brackets

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 12 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

GXV3610_HD/FHD v2 Specifications

Model v2

GXV3610_HD

GXV3610_FHD

Video Compression

H.264, MJPEG

Image Sensor Resolution

1/3”, 1.2 Megapixel Progressive

Scan CMOS, 1280H x 960V

1/3”, 3.1 Megapixel Progressive

Scan CMOS, 2048H x 1536V

Image Sensor Sensitivity

Day/Night mode, exceptionally low noise, low light levers. Shutter:

1/10000 – 1/30 second

Focal Length

3.6mm

Aperture

F1.8

Field Angle (FOV)

100.2°(D) x 77°(H) x 54°(V)

IR Cut Filter

Yes, Mechanical

Day & Night Mode

IR LED covering up to 10 meter, with full software control

Minimum Illumination

0.05 Lux, 0 lux with IR LED On

Responsivity

5.48V/lux-sec (550nm)

1.9V/lux-sec (550nm)

Supported Maximum Video

Resolution and Frame Rate

1280x960 (25fps)

1280x720 (30fps)

2048x1536 (15fps)

1920x1080 (30fps)

Video Bit Rate

32 Kbps ~ 8 Mbps, multi-rate for preview & recording

Audio Input

Built-in Microphone

Audio Output

3.5mm Line-Out (600Ω, 0.707 Vrms)

Audio Compression

G.711u/a (PCMU, PCMA)

Embedded Analytics

Motion Detection (up to 16 target areas)

Pre-/post-alarm Recording

Yes, 8MB

Yes, 3MB

WDR (Wide Dynamic Range)

No

Yes (100dB)

Snapshots

Triggered upon events, send via email/FTP

Network Protocol

TCP/UDP/IP, RTP/RTCP, RTSP, DHCP, DDNS, HTTP, HTTPS,

SMTP, FTP, NTP

SIP/VoIP Support

Yes

Time-Lapse Photography

Yes

Privacy Mask Support

Yes, 4 Zones

Power over Ethernet (PoE)

IEEE 802.3af, Class 0; 10M/100M Auto-sensing,

2KV Lightning Surge Protection

External Cable Connection

Network: RJ45, 10M/100M auto-sensing

3.5mm Line-Out

Power Input (12VDC/1A)

Dimensions (D x H)

120mm (D) x 100mm (H)

Weight

0.7kg

Temperature / Humidity

Operating: -20°C ~ +50°C (-4°F ~ 122°F),

10–90% RH (non–condensing)

Storage: -30°C ~ +60°C (-22°F ~ 140°F)

Power Adapter

Output: 12VDC/1A; Input: 100–240VAC, 50–60Hz

Casing

IP66 compliant weather-proof metal case

Compliance

FCC Part 15,Subpart B Class B; EN 55022 Class B,

EN 61000-3-2, EN 61000-3-3, EN 55024, EN 60950-1;

C-tick AS/NZS CISPR 22, CISPR24; IP66

Table 1: GXV3610_HD/FHD v2 Technical Specifications

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 13 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

INSTALLATION GUIDE

Minimum Recommended Computer System Requirement

To install GXV3610_HD/FHD v2, you have to have a computer, PC recommend.

The minimum recommended PC system requirement listed below:

• Windows XP, Windows Vista, Windows 7 and Windows 8

• CPU: Intel Pentium 4 or higher, 2 GHz

• RAM: 2 GB (4 GB recommended for larger systems)

• Support for DirectX 8.0 and above.

Configure the GXV3610_HD/FHD v2 via Web Browser

The GXV3610_HD/FHD v2 has embedded Web server to respond to HTTP GET/POST requests.

Embedded HTML pages allow user to configure the IP camera through Microsoft Internet Explorer (7.0 or

above), Firefox and Chrome (plug-in from Grandstream required).

• Download WebControl Plug-in from Grandstream website:

http://www.grandstream.com/products/tools/surveillance/webcontrl_plugin.zip

For Apple platform OS-X, only MJPEG video coded supported currently.

NOTE:

 Please temporarily disable Antivirus or Internet Security Software when download and install the

Grandstream WebControl Plug-in for Firefox/Chrome or “GSViewerX.cab” for Microsoft Internet

Explorer. Please close Browser to install the downloaded Plug-in or Active-X.

 Please trust and install the file downloaded if prompted by the Antivirus or Security software.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 14 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

Connect the Camera to network with DHCP server (Recommended)

The GXV3610_HD/FHD v2 by default enabled as DHCP client, it will automatically get IP address from

the network with DHCP server running.

WINDOWS PLATFORM:

There are two ways for Windows user to get access to the IP Camera easily:

A. UPnP

By default, the GXV3610_HD/FHD v2 has the UPnP feature turned ON. For customers using Window

network with UPnP turned on (most SOHO router support UPnP), it is very easy to access the IP camera:

• Find the “Network” icon at Windows Desktop.

• Click the icon to get into the “Network” and the IP cameras will list as “Other Devices” shown like

below. Refresh the pages if nothing displayed. Otherwise, the UPnP may not active in the network.

Figure 2: Windows “Network” showing GXV3610_HD/FHD v2 as “Other Devices” via UPnP

• Click the displayed icon of related IP camera, the default browser (e.g.: Firefox or Chrome) will open

and connect directly to the camera’s webpage, prompt message will display asking for plug-in

installation.

• Disable security or antivirus software, download the plug-in, close browser and install the plug-in,

open the browser again, the embedded video will be displayed if clicking the icon of the related IP

Camera.

B. “GS_Search” Utility Tool

User can know the IP address assigned to the camera from DHCP server log or using the Grandstream

GS_Search tool. Following is the instruction for using “GS_Search” utility tool:

1. Download the GS_Search tool from Grandstream website:

http://www.grandstream.com/products/tools/surveillance/GS_Search.zip

2. Run the Grandstream GS_Search tool by double click the unzipped “GS_Search.exe”.

3. Click on the button to begin device detection

4. The detected devices will appear in the output field like below

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 15 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

Figure 3: “GS_Search” Result Page of GXV3610_HD/FHD v2

5. Double click the column of the detected camera, the browser will automatically open and link to the

device IP and the web configuration page.

6. The browser will ask for plug-in or ActiveX if not installed, otherwise it will get to Home page and

start to show the video captured by the camera (by default the camera enabled anonymous access)

7. Click “Configuration” icon, the browser will ask credentials to authorize configuration.

8. Enter the administrator user name and password to access the Web Configuration Interface, the default

user name and password are both set to admin.

9. In step 6, browser will indicate that “This website wants to install the following add-on:

GSViewerX.cab from Grandstream Networks Inc.” Please allow the installation.

10. The plug-in can be download here:

http://www.grandstream.com/products/tools/surveillance/webcontrl_plugin.zip

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 16 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

APPLE PLATFORM:

For Apple users, please turn on Bonjour of Safari to find and access the GXV3610_HD/FHD v2.

1) Open Safari, select “Advanced” to open the Advanced Setting.

2) Click “Include Bonjour in the Bookmarks menu” and “Include Bonjour in the Favorites bar” then close

the setting page and back to Safari.

Figure 4-1: Apple Safari “Bonjour” Setting page to display GXV3610_HD/FHD v2

3) Bonjour will now display embedded at Safari. Select “Bonjour” pull-down menu and select

“Webpages”, the related IP Camera like GXV3610_HD/FHD v2 will be there.

Figure 4-2: Apple Safari “Bonjour” Setting page to display GXV3610_HD/FHD v2

4) Click the displayed camera to access to the configuration page of the camera.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 17 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

5) To see the video, user has to change the video codec from default H.264 to MJPEG, and type in

following to URL:

http://IP_Address_Camera:Port/mjpeg/mjpegX.html

(X: 0, 4 represent 1

st

, 2

nd

stream, Default Port: 80)

NOTE:

 The instruction given here based on Safari/OS-X, other Apple platform like iOS (iPhone/iPad) can

use similar method.

 iPhone/iPad (iOS) users are recommended to use Applications in Apple Store.

 Free or Paid applications from Apple Store like “IP Cam Viewer” are suggested and verified

working with Grandstream IP Cameras like GXV3610_HD/FHD v2.

 Apple Store applications like “IP Cam Viewer” will support H.264 video codec.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 18 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

Connect to the Camera using Static IP

If no DHCP server in the network, or the camera does not get IP from DHCP server, user can connect the

camera to a computer directly, using static IP to configure the camera.

The default IP, if no DHCP server; or DHCP offer time out (3 minutes), is 192.168.1.168

1. Connect the computer RJ-45 via an Ethernet cable directly to the IP camera GXV3610_HD/FHD v2.

2. Configure the computer using Static IP: 192.168.1.XXX (1<XXX<255, but NOT 168) and configure

the “Subnet mask” to “255.255.255.0”. Leave the “Default Gateway” to “Blank” like below:

3. Power on the GXV3610_HD/FHD v2.

4. Start the browser when the network connection is up.

5. Enter 192.168.1.168 in the address bar of the browser.

6. The browser will ask for plug-in or ActiveX if not installed, otherwise it will get to Home page and

start to show the video captured by the camera (by default the camera enabled anonymous access)

7. Click “Configuration”, the browser will ask credentials to authorize configuration.

8. Enter the administrator user name and password to access the Web Configuration Interface, the default

user name and password are both set to admin.

9. In step 6, IE will indicate that “This website wants to install the following add-on: GSViewerX.cab

from Grandstream Networks Inc.”, allow the installation.

10. Firefox, Chrome user need to download and install the plug-in to see the video, the plug-in is here:

http://www.grandstream.com/products/tools/surveillance/webcontrl_plugin.zip

NOTE:

 Please temporarily disable Antivirus or Internet Security Software and close all browsers when

download and install the Grandstream Plug-in Software.

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 19 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

GXV3610_HD/FHD V2 APPLICATION SCENARIOS

GXV3610_HD/FHD v2 is very versatile infrared IP Camera, it can be used in a lot of scenarios.

LAN w/o Internet

For multi-room or a bigger space, multiple GXV3610_HD/FHD v2 might be required. User can

establish a local area network using PoE switch.

If remote access required, a router with internet access may add in.

Equipment List:

1) Several GXV3610_HD/FHD v2

2) Ethernet cables

3) Switch (Static IP required to configure to IP Cameras)

4) PoE Switch (Optional, better solution)

If remote access to the cameras required to view the LIVE video stream, then broadband Internet is

required and more equipment required:

5) Router (if DHCP configured than static IP is not required although still recommended)

6) Broadband Internet Access (FiOS, Cable or DSL)

7) iPhone or Android phone. (Application like “IP Cam Viewer”)

Figure 5-1: GXV3610_HD/FHD v2 Working in LAN

Grandstream Networks, Inc. GXV3610_HD/FHD v2 User Manual Page 20 of 59

Firmware Version 1.0.3.14 Last Updated: 11/2015

LAN with Internet

For multi-room or a bigger space, with Internet access and local video recording required,

following list is recommended:

Equipment List:

1) Several GXV3610_HD/FHD v2

2) GVR3550 NVR

3) Ethernet cables

4) Switch (PoE Switch recommended)

5) Router

6) Broadband Internet Access (FiOS, Cable or DSL)

7) iPhone or Android phone. (Application like “IP Cam Viewer”)

8) GSurf_Pro Remote Access (Optional)

Figure 5-2: GXV3610_HD/FHD v2 Working with GVR3550 and/or GSurf_Pro with Internet

Page is loading ...

Grandstream GXV3610 v2 series User manual

This manual is also suitable for

Grandstream GXV3610 v2 series User manual

Related papers

Other documents