Bewator PD30EM Installation & User Manual

PD30EM & PD40EM

Installation & User Manual

DE FREN SV

Book contents

English ............................................... 3

Svenska .............................................17

Deutsch .............................................31

Français .............................................45

PD30EM & PD40EM Installation and User manual 3

ENG

English

Material from this manual may only be copied with the consent in writing of Bewator.

Bewator reserves the right to alter both the content of the manual and the design of the

product.

Document number: 81618-9

Bewator AB develops and markets a complete security product range that includes access

control, intruder alarm and video control. Sales, installation and servicing are handled by

an International national dealer network.

Actions (such as unauthorised editing manipulation, copying etc.) must not be taken

with the software contained in the products and systems. Such actions are regarded as

copyright violation and may result in imprisonment or fines and may likewise lead to an

obligation to pay damages and compensation for using the software.

4 PD30EM & PD40EM Installation and User manual

ENG

Contents

About this manual ...............................................................5

ProxCodoor - General ..........................................................5

Supplied material........................................................... 6

Addressing .................................................................... 6

PD30EM installation............................................................7

Recommended lock cases for the PD30EM .................... 10

PD40EM installation ......................................................... 11

Recommended lock cases for the PD40EM .....................14

Technical data ................................................................... 15

Using the ProxCodoor ....................................................... 15

PD30EM & PD40EM Installation and User manual 5

ENG

About this manual

This manual covers both the Scandinavian style (PD30EM) and the

International style (PD40EM) of the ProxCodoor. In the scope of this

manual we will use the name ProxCodoor (unless notified.)

ProxCodoor - General

The ProxCodoor is a system component in the Bewator Entro Access

Control system range of products. It could be used indoors in general

(sales floor, shops, restaurants, manufacturing and assembly areas,

entrance and storage rooms). ProxCodoor is based on the popular

Codoor electromechanical codelock, but instead of a keypad it includes

a proximity reader which reads tags/cards of type EM4102. It is powered

from the system and connects (via a dropbox) to the local bus in Bewator

Entro and communicates with a Segment Controller.

The ProxCodoor is suitable for most doors with handle-operated

mortice locks. Check suitability by simply measuring your own lock. (See

further on the recommendations for each model).

It then requires only that the supplied 4-wire cable is mounted from

the dropbox through the door to the lockcase.





























































1   %3#

  

1

11:30

The illustration shows the PD30EM - but the PD40EM is mounted in a

similar way.

6 PD30EM & PD40EM Installation and User manual

ENG

Supplied material

The ProxCodoor kit consists of the following parts:

The ProxCodoor unit with integrated proximity reader and 20 cm

cable (with connector matching the long cable).

Dropbox for connection to Entro.

5 metre cable with a 4-pin connector and a free end to be connected

to the dropbox.

Extension sleeves for handle nipples (use only one pair).

1 reinforcing spring.

1 reinforcing spring holder.

Additionally you need some kind of door loop to feed the cable from the

door to the dropbox.

NOTE! No batteries should be mounted in the unit (although there are

cutouts in the back).

Addressing

Before finally mounting the unit the address must be set between 1 - 32.

This is recommended to be done without power (unless the software

might not recognise any change). There are a two rotary switches at the

back of the unit where the arrows indicates the selected digits. If you

have the address switches upwards it looks like the figure.

The address is conformed of two digits:

1st digit (left): 0 - 3

2nd digit (right): 0 - 9

This will correspond to the address ranges used in the Entro system.















































































•

PD30EM & PD40EM Installation and User manual 7

ENG

PD30EM installation

Remove the cylinder ring and the door handle from the door by

loosening the four screws. See photo .

The lever handle spindle should project no more than 20 mm on the

outside of the door. If the spindle is too long, push it through into

the handle on the inside. If this cannot be done, cut the spindle to

the right length. See photo .

Screw the supplied extension sleeves to the nipples for the handle.

Use the appropriate size sleeve to suite the bolts supplied with the

handles. Note! If neccessary, this must be mounted on the opposite

side of ProxCodoor (inside) See photo .

1.

2.

3.







8 PD30EM & PD40EM Installation and User manual

ENG

Disassemble the lockcase from the door and cutout enough space

for the cable entry at the bottom of the hole inside the handle. Also

be sure there is space to finally feed the cable connector (and some

remaining cable) beneath the lockcase. See figure .

!

PD30EM

Figure 

Install the cable from the lockcase to the door loop and further to

the place for the dropbox. You may have to drill a hole through the

door between the lockcase and the door loop.

Mount the dropbox somewhere above the door, less than 5 metres

from the lockcase and connect the 4-wire cable according to the

following table.

Colour on cable Drop box (PL2)

Signal

Alt. 1

Alt. 2

*)

V+

Pair 1

Red

Green

1

0V Black

Black

2

Com B

Pair 2

White

3

Com A Green

Black

4

Screen

- -

5

*) May exist in older versions.

4.

5.

6.

PD30EM & PD40EM Installation and User manual 9

ENG

Put the connectors in the PD30EM together and place them in the

space beneath the lockcase. Be sure that the guides are matching

each other. See figure .

Push the lockcase back in final position. (Possibly wait to tighten it

until the system is tested).

Place the PD30EM on the outside of the door with the handle

attached, and pass the lever handle spindle through the square

hole. See photo .

Note! The red mark on the follower should always point downwards.

Feed the cable to the space at the outer side of the lockcase.

Tighten, not too hard, the four previously loosened screws (the

screws for the handle first). See photo .

Log on an authorised card (or tag) in Entro and test it on PD30EM.

You can that see that the unit operates correctly by seeing the yellow

LED (on the front) flashing, until five readings are performed. The

LED will then go off.

Ready!

RED





7.

8.

9.

10.

11.

12.

10 PD30EM & PD40EM Installation and User manual

ENG

Recommended lock cases for the PD30EM

PD30EM is suitable for most doors with handle-operated mortice locks.

Check suitability by simply measuring your the distance between the

center of the handle follower and the center of the cylinder. The backset

should normally be 70 mm.

The PD30EM can be used with many types of locks, like e g ASSA 8761

or 765 etc. If in doubt please check with your local locksmith.

5 -

116 mm

01

8x8 mm

8

3

-

0

3

"ACKSETMM

Basic needs are the following:

The distance between the centre of the handle and the centre of the

cylinder should be between 105 – 116 mm.

Latchbolt function.

The handle must have an 8 mm square spindle.

The handles fixing holes 30-38 mm (diagonal).

NOTE! PD30EM is only for internal fitting and operation and should

neither be specified for back to back installation.

•

PD30EM & PD40EM Installation and User manual 11

ENG

PD40EM installation

Remove the cylinder ring and the door handle from the door by

loosening the four screws. See photo .

The lever handle spindle should project no more than 20 mm on the

outside of the door. If the spindle is too long, push it through into

the handle on the inside. If this cannot be done, cut the spindle to

the right length. See photo .

Screw the supplied extension sleeves to the nipples for the handle.

Use the appropriate size sleeve to suite the bolts supplied with the

handles. See photo .

1.

2.

3.







12 PD30EM & PD40EM Installation and User manual

ENG

Disassemble the lockcase from the door and eventually cutout

enough space for the cable entry beside the lockcase. Also be sure

there is space to finally feed the cable connector (and some

remaining cable) beneath the lockcase. See figure .

Figure



!

PD40EM

Install the cable from the lockcase to the door loop and further to

the place for the dropbox. You may have to drill a hole through the

door between the lockcase and the door loop.

Mount the dropbox somewhere above the door, less than 5 metres

from the lockcase and connect the 4-wire cable according to the

following table.

Signal Colour on cable Drop box (PL2)

V+

Pair 1

Red 1

0V Black 2

Com B

Pair 2

White 3

Com A Green 4

Screen

-

5

4.

5.

6.

PD30EM & PD40EM Installation and User manual 13

ENG

Put the connectors in the PD40EM together and place them in the

space beneath the lockcase. Be sure that the guides are matching

each other. See figure .

Push the lockcase back in final position. (Possibly wait to tighten it

until the system is tested).

Place the PD40EM on the outside of the door with the handle

attached, and pass the lever handle spindle through the square

hole. See photo .

Note! The red mark on the follower should always point upwards.

Feed the cable to the space at the outer side of the lockcase.

Tighten, not too hard, the four previously loosened screws (the

screws for the handle first). See photo .

Log on an authorised card (or tag) in Entro and test it on PD40EM.

You can that see that the unit operates correctly by seeing the yellow

LED (on the front) flashing, until five readings are performed. The

LED will then go off.

Ready!

RED



7.

8.

9.

10.

11.

12.



14 PD30EM & PD40EM Installation and User manual

ENG

Recommended lock cases for the PD40EM

PD40EM is suitable for most doors with e g ASSA Euro locks. Check

suitability by simply measuring your own lock. The distance between the

centre of the handle and the centre of the cylinder should be 72 mm and

the handle fixing holes 38 mm. The backset should normally be 55 or 60

mm (but are normally not critical for PD40EM).

The PD40EM can be used with many types of locks, like e g ASSA 8720

If in doubt please check with your local locksmith.

55/60 mm

72 mm

8 mm

38 mm

88/93 mm

Basic needs are the following:

The distance between the centre of the handle and the centre of the

cylinder should be 72 mm.

The handle must have an 8 mm square spindle.

The handles fixing holes 38 mm.

NOTE! PD40EM is only for internal fitting and operation and should

neither be specified for back to back installation.

•

PD30EM & PD40EM Installation and User manual 15

ENG

Technical data

Power supply: 8 - 40 Vdc, 8 - 30 Vac.

Power consumption: 100 mA.

Interface: Connects to Bewator Entro (via dropbox)

Housing Stainless steel.

Colour: Stainless.

Environment: Indoors in general ( sales ﬂoor, shops, res-

taurants, manufacturing and assembly areas,

entrance and storage rooms).

Temperature range: 0°C to +50 °C.

Dimension (HxWxD) mm: PD30EM: 245 x 64 x 47.

PD40EM: 255 x 70 x 54.

Using the ProxCodoor

When presenting a valid tag (card) a click is heard, a green LED lights

and the handle can be used to open the door. If the handle is not used

within 4 seconds the PD30EM will be locked again which prevents the

door from being unintentionally being unlocked.

In the Bewator Entro the security level Unlocked can also be set,

where a time schedule may be used to control when door can be opened

(without using any tag). A green LED is lit as long as the PD30EM is

unlocked.

Page is loading ...

Bewator PD30EM Installation & User Manual

This manual is also suitable for

Bewator PD30EM Installation & User Manual

in other languages

Related papers

Other documents