SILVERMINE Stone Operating instructions

Stone
Brand
SILVERMINE
Model
Stone
Type
Operating instructions

Below you will find brief information for 36" Pillar Kit, 48" Pillar Kit. This document provides instructions for assembling Silvermine Pillar Kits. The kit includes a pillar frame, pillar cap, and pre-cut pillar stones. The first step involves assembling the frame using provided screws. Next, the frame is mounted and secured to a base. Then, the stone is attached using fasteners, building up each layer. The final step involves adding a pillar cap using construction adhesive, completing the pillar structure.

Below you will find brief information for 36" Pillar Kit, 48" Pillar Kit. This document provides instructions for assembling Silvermine Pillar Kits. The kit includes a pillar frame, pillar cap, and pre-cut pillar stones. The first step involves assembling the frame using provided screws. Next, the frame is mounted and secured to a base. Then, the stone is attached using fasteners, building up each layer. The final step involves adding a pillar cap using construction adhesive, completing the pillar structure.

The First Brand of Mortarless Stone Veneer
silverminestone.com
Pillar Kits
Instructions
Pillar Kit Includes:
Tools Needed (not included)
1324.2
4.1
VOILA!
Pillar Cap
Pillar Stones
Level 1/2” piece of wood Construction
Adhesive
8
6
· Pillar Cap
· Pre-Cut Pillar Stones
36” Pillar Kit .........................3 boxes
48” Pillar Kit .........................4 boxes
· Pillar Frame Kit
Right Side Panel
Left Side Panel
Back Side Panel
Upper Front Panel
Lower Front Panel
Stainless Steel Frame Assembly Screws
Top Frame Plate
Silvermine Stone Fasteners
1
2
3
4.2
4.1
6
5
8
Drill
5
Step 1 ASSEMBLE THE FRAME
A. ATTACH - Back Panel to Right Side Panel using (5) stainless steel screws
B. ATTACH - Left Side Panel to Back Panel using (5) stainless steel screws
C. ATTACH - Long Front Side Panel to the TOP of Left Side Panel using
(3) stainless steel screws
D. ATTACH - Long Front Side Panel to the TOP of Right Side Panel using
(3) stainless steel screw
E. Insert top plate onto assembled frame sides
1
1
2
2
3
3
4.1
4.1
Frame Panels
12
3
4.1
Step 1 STEP-BY-STEP
Step 1 - A Step 1 - B Step 1 - C & D
1 1
33
24.1
NEEDED ITEMS FOR THIS STEP
6
Drill
(not included)
Stainless Steel Screws
5
Top Plate
6
Step 2 MOUNTING THE FRAME
A. Set assembled pillar frame in place with the 2x4 base blocks on the bottom
B. Use Level (not included) to ensure frame is plumb - Shim if necessary
C. Attach mounting blocks to your base with appropriate mounting hardware (not
included) (See local building codes)
D. Attached short, front panel to pillar frame using stainless steel screws to fully
enclose it
Mounting Hardware for Pillar
Frame Base
(not included)
See Local Building Codes
Step 2 STEP-BY-STEP
Frame Panel
4.2
4.2
2x4 Base Blocks
Level
(not included)
Step 2 - D
4.2
VOILA!
NEEDED ITEMS FOR THIS STEP
Stainless Steel Screws
5
Drill
(not included)
First Course of Stone
Step 3 ATTACHING THE FIRST COURSE OF STONE
A. Use a temporary support (1/2” wood piece or similar material - not included) to
support first course of pillar stone and keep it level with the bottom edge of the
pillar frame.
B. Attach Pillar Stone to Pillar Frame with Silvermine Stone Fastener
- Use 2 screws per panel
- Place screw 3/4” - 1” above pillar stone and 1”
from the edge, into the metal flashing.
- Use Level
C. Repeat Step 3B for the remaining bottom course of pillar stones
TIP: Be sure to use your level! The first row sets the stage for the remaining stone
layers - so be diligent on making sure this row is level.
Step 3 STEP-BY-STEP
Pre-Cut
Stones
Level
(not included)
NEEDED ITEMS FOR THIS STEP
1/2” piece of wood
FRONT SIDE
Pillar Frame
Silvermine Stone
Fasteners
8
Drill
(not included)
1/2” Piece of Wood
(not included)
Step 4 BUILDING UP YOUR STONE PILLAR
A. Remove temporary support
B. Repeat Step 3B for each course of stone*
*Make sure that each stone is firmly in contact with the stone below it
When ONE COURSE of stone remains to be adhered...
C. Bend metal flashing horizontally
D. Install the last course of pillar stone by attaching the (now horizontal) flashing to
the top of the pillar frame
NOTE: Each piece of flashing should have 2 screws - but as panels overlap, it
is okay to use one screw to hold multiple pieces
E. Using a bead of construction adhesive (not included), install the pillar cap to the top
of your built pillar structure
Step 4 STEP-BY-STEP
Pre-Cut
Stones
Level
(not included)
Pillar Cap
NEEDED ITEMS FOR THIS STEP
One remaining
course of stone
Step 4 - E
Top Down ViewBending the Flashing
Silvermine Stone
Fasteners
8
Step 4 - C & D
Drill
(not included)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

SILVERMINE Stone Operating instructions

Stone
Brand
SILVERMINE
Model
Stone
Type
Operating instructions

Below you will find brief information for 36" Pillar Kit, 48" Pillar Kit. This document provides instructions for assembling Silvermine Pillar Kits. The kit includes a pillar frame, pillar cap, and pre-cut pillar stones. The first step involves assembling the frame using provided screws. Next, the frame is mounted and secured to a base. Then, the stone is attached using fasteners, building up each layer. The final step involves adding a pillar cap using construction adhesive, completing the pillar structure.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents