Phanteks REVOLT PH-P1000PR_BK01C Installation guide

REVOLT PH-P1000PR_BK01C
Phanteks
Brand
Phanteks
Model
REVOLT PH-P1000PR_BK01C
Type
Installation guide

Phanteks REVOLT PH-P1000PR_BK01C is a 1000W power supply that offers a range of features for a variety of use cases. With its cable-free design, you can choose only the cables you need for your build, ensuring a clean and efficient setup. The Revolt is equipped with the latest PCIe Gen5 (12VHPWR) GPU connector, providing up to 600W of power to compatible graphics cards. Additionally, it comes with a Hybrid Fan Mode that allows you to activate 0 RPM mode for near-silent operation under low loads.

Phanteks REVOLT PH-P1000PR_BK01C is a 1000W power supply that offers a range of features for a variety of use cases. With its cable-free design, you can choose only the cables you need for your build, ensuring a clean and efficient setup. The Revolt is equipped with the latest PCIe Gen5 (12VHPWR) GPU connector, providing up to 600W of power to compatible graphics cards. Additionally, it comes with a Hybrid Fan Mode that allows you to activate 0 RPM mode for near-silent operation under low loads.

INSTALLATION GUIDE SUPPORTS
PH-P1000PR_BK01C
PH-P1000PR_WT01C
PH-P1200PR_BK01C
PH-P1200PR_WT01C
PH-P1600PR_BK01C
PH-P1600PR_WT01C
PH-P1300TR_BK01C
PH-P1300TR_WT01C
PH-P1600TR_BK01C
PH-P1600TR_WT01C
SUPPORT
US & Canada
[email protected]
International
[email protected]
FOLLOW US ON
SOCIAL MEDIA
Instagram
Phanteks
Facebook
Phanteks
YouTube
Phanteks
Twitter
@phanteks
CONNECTOR QUANTITY 1000/1200 watt models 1300 watt models 1600 watt models
Motherboard 10+18-PIN 1 1 1
CPU | PCIe 8-PIN 5 9 9
PCIE GEN5 12VHPWR 1 1 2
SATA | MOLEX 5 6 6
INCLUDED ACCESSORIES
User Manual
Installation Guide
PSU Bag
Zip Tie Bag
Velcro Bag
Screw Pack
Power Cable
CPU | PCIe
8-PIN
PCIE GEN5
12VHPWR
ACCESSORIES INCLUDED
AVAILABLE OUTPUT CONNECTORS
POWER SUPPLY
REVOLT
MANUAL
WARRANTY
POWER CABLE
1500MM
SCREW PACKZIP TIE BAG VELCRO BAG
MOTHERBOARD
10+18-PIN
SATA | MOLEX
6-PIN
CHOOSE YOUR CABLES
01
INSTALL POWER SUPPLY INTO CHASSIS
02
CONNECT CABLES TO POWER SUPPLY
03
INSTALLATION GUIDE
The Revolt power supply comes as a cable free model, cables are purchased
separately. Make sure the cables are compatible with the Phanteks Revolt
power supply before proceeding.
Cables sold separately
Install the Revolt PSU in the computer chassis using the 4x PSU screws. Follow
the chassis instruction manual.
Connect all needed cables to the power supply according to the overview
below. The exact connector lay-out and quantity may be different depending
on the model.
Activate the 0 RPM mode with the Hybrid Fan button on the rear to go for
absolute silence when under low load. The Revolt will control the fan speed
intelligently based on load and temperature.
ULTIMATE SILENCE WITH HYBRID FAN CONTROL
05
CONNECT POWER CABLE
06
BE SAFE!
07
PCIE GEN5 GPU CONNECTOR
04
The Revolt is equipped with the PCIe Gen5 (12VHPWR) GPU connector. Make
sure it is fully seated and clicked in to prevent any damage to your system.
Note that a compatible GPU is required.
Connect the power cable to the power supply and a
grounded power outlet respectively. Make sure the power
supply is turned off ‘O’ before connecting it to a power outlet.
Hybrid Fan Mode is turned on when the button is in the
‘OUT’ position and turned off when pushed ‘IN’.
Switch the power button to the ‘I’ position to turn on
your system.
When making any changes to the hardware, be sure
that the power button is switched from the ‘I’ to the ‘O’
position so the power supply is turned off.
Phanteks will not take responsibility for any damages incurred due to incorrect installation or usage of this product.
PCIe GEN5
12VHPWR CABLE
Pre-connect all needed cables to the
PSU before installing it into the chassis.
See step 3
PRO TIP
PSU SCREW
INSTALL
4x
  • Page 1 1
  • Page 2 2

Phanteks REVOLT PH-P1000PR_BK01C Installation guide

REVOLT PH-P1000PR_BK01C
Phanteks
Brand
Phanteks
Model
REVOLT PH-P1000PR_BK01C
Type
Installation guide

Phanteks REVOLT PH-P1000PR_BK01C is a 1000W power supply that offers a range of features for a variety of use cases. With its cable-free design, you can choose only the cables you need for your build, ensuring a clean and efficient setup. The Revolt is equipped with the latest PCIe Gen5 (12VHPWR) GPU connector, providing up to 600W of power to compatible graphics cards. Additionally, it comes with a Hybrid Fan Mode that allows you to activate 0 RPM mode for near-silent operation under low loads.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents