To the mains socket
Connect one end of the RF coaxial cable to the aerial
socket on the wall and the other end of the cable to
the AERIAL IN socket at the rear of your TV.
Connecting to the Mains Socket
1. Connect the mains adapter to the mains socket
after you have completed all the connections. At
this stage, the TV switches to standby mode. The
red LED indicator will illuminate on the front panel
of the TV.
2. In standby mode, press the button on the
remote control to turn the TV on. The red LED
indicator will turn blue.
Installing the Base StandUnpacking
Remove all packaging from the TV. Retain the packaging.
If you dispose of it please do so according to local regulations.
TV
TV Stand
Remote Control/AAA Batteries x 2
Screw x 4
Component Adapter Cable (YPbPr)
Composite Adapter Cable (AV)
Instruction Manual
Operating Your Remote Control
1. Press and lift the back cover to
open the battery compartment
of the remote control.
2. Insert two AAA size batteries.
Make sure to match the (+) and
( - ) ends of the batteries with
the (+) and ( - ) ends indicated
in the battery compartment.
3. Close the battery compartment
cover.
Turning On and Tuning In the TV
The first time you turn the TV on, the above menu will appear
on the screen.
Please ensure the aerial is plugged in.
1. Press the buttons to select your desired country.
The default country is Ireland. Then press OK.
Country:
Please ensure your
aerial is plugged in
before tuning in your TV.
- Setup 1 -
Move
Enter
Ok Exit
Exit
Ireland
Austria
Slovskia
Croatia
Serbia
Auto Installation
Next Page
Exit
Exit
Auto Installation
DTV channels found:
Radio channels found:
CH:22 482000 KHz
Process
0
0
9%
Quick Start Guide
Language:
- Setup 2 -
Move
Enter
OK Exit
Exit
English
French
Italian
Spanish
Netherland
Auto Installation
Previous Page Next Page
Auto Search
- Setup 3 -
Move
Enter
OK Exit
Exit
Auto Installation
Previous Page
DTV
Connecting the Aerial
2. Press the buttons to select your desired language. The
default language is English. Then press OK.
3. Press the OK button. Your TV will now start to tune in all
available channel.
The above menu will appear, the tuning process will take a few
minutes. When a picture appears your TV has finished tuning.
Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these features,
please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call our Call Centre on 1 890 818 575.
Our Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
QSG-L26HED13/L26HE13I-130917V1
26” HD Ready LED TV
with DVD Player
L26HED13I
L26HE13I
(Non-DVD version)
VGA (PC)
DC IN
PC
Audio In
SCART
To the mains
socket
Coaxial
Out
1. Disconnect all cables connected to the TV.
2. Lay the TV down on a flat surface ideally on the edge of a table so the
base of the TV slightly overhangs the edge of the table, with the back
side facing up. Please make sure a soft cushioned material (such as
a dry bath towel or thick piece of foam)
is placed beneath the screen.
Cushioned
material
3. Place the
plastic collar onto
the neck of the
TV stand as shown.
4. Place the glass over the screw holes on the neck of the TV stand
and attach using the 4 screws provided. Make sure you attach the
glass the right way around, so that the majority of the glass stand is
towards the front of the TV.
*TV stand installation may vary depending on model
L26HED13I_QSG.indd 1 17/09/2013 09:09
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Currys Essentials C19DIGB10 Quick start guide
-
-
JVC LT-32C345 User manual
-
Sandstrom S46LDIB10 User manual
-
-
-
-
-
JVC LT-24C341 User manual
-
Bush 40INCH CTV401DVD FVHD LED TVCOMBI User manual