Intex 26377EH Owner's manual

26377EH
Intex
Brand
Intex
Model
26377EH
Category
Above ground pool accessories
Type
Owner's manual

This manual is also suitable for

(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
English
97PO
English
IMPORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before installing
and using this product.
Deluxe Maintenance Kit
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6 839
Monday through Friday, 8:30am to 5:00pm Pacific Time
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and
boats available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex
reserves the right to change specifications and appearance,
which may result in updates to the instruction manual without
notice.
097-*PO-R
0-1805
For illustrative purposes only. Pool may not be provided.
097-*PO-R0-2104
OWNER’S MANUAL
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 2
Warnings........................................................................ 3
Parts Reference............................................................. 4-5
Hook Assembly for Easy-Set
®
Pools with
Inflatable Top Rings...................................................... 6
Hook Assembly for Metal Frame Pools....................... 7
Surface Skimmer Setup Instructions........................... 8-10
Pool Vacuum Setup Instructions................................. 11-14
Pool Vacuum Operating Instructions.......................... 14
Hand-held Skimmer Assembly and
Operating Instructions.................................................. 15
Hand-held Brush Assembly and
Operating Instructions.................................................. 15
Long Term Storage........................................................ 16
General Aquatic Safety................................................. 16
TABLE OF CONTENTS
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 3
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
WARNING
• Do not permit children to use this product. Adult use only.
• Do not operate the filter pump while the pool is occupied or in use.
• Strong suction. Do not remove or obstruct the floating cover opening
while the filter pump is operating!
• Keep hands and hair away from the skimmer and floating cover
opening when the filter pump is operating!
• Turn off or unplug the filter pump before adjusting, cleaning,
servicing or removing the skimmer, basket or floating cover.
• Remove all maintenance items when the pool is in use.
• Keep telescoping aluminum handle away from any overhead power
lines.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY, DROWNING OR DEATH.
These product warnings, instructions and safety rules provided with the
product represent some common risks of water recreation devices and do
not cover all instances of risk and danger. Please use common sense and
good judgement when enjoying any water activity.
Filter Pump Flow Rate Requirement:
1000 - 4000 gallons/hour (3785 - 15140 liters/hour)
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 4
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the
contents and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
20
20
21
22
23
24
26
25
27
28
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 5
REF. NO.
DESCRIPTION QTY.
SPARE
PART NO.
EASY-
SET
®
POOL
FRAME
POOL
COMMON
1 HOSE SEAL 1 10134
2 HOSE O-RING 1 10262
3
VACUUM COVER (HOSE SEAL & HOSE O-RING INCLUDED)
1 11095
4 DEBRIS BAG 1 10788A
5 VACUUM BODY 1 10789
6 FLOATING COVER 1 11075A
7 COVER RIM 1 11076
8 BASKET HANDLE 1 11077
9 BASKET (BASKET HANDLE INCLUDED) 1 11078
10 SKIMMER 1 11079
11 SCREW 1 10526
12 DEPTH ADJUSTER 1 10522
13 HOOK (OPTIONAL) 1 10521
14 ARM (OPTIONAL) 1 10520
15 FRAME HOOK (OPTIONAL) 1 11502
16 SKIMMER HOSE 1 10531
17 HOSE ADAPTOR B 1 11238A
18
VACUUM HEAD ( HANDLE ADAPTOR, SPRING, PIN & BRUSH INCLUDED)
1 10791A
19 HANDLE ADAPTOR 1 10792
20 SPRING 3 10794
21 PIN 1 10793
22 BRUSH 8 10795A
23 SKIMMER NET (SPRING INCLUDED) 1 10796A
24 BRUSH HEAD (SPRING INCLUDED) 1 11073A
25 VACUUM HOSE 1 10797
26 HOSE CLAMP 2 10122
27 TELESCOPING ALUMINUM HANDLE 1 10798A
28
FLOW REDUCTION ADAPTER
1 11237
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 6
HOOK ASSEMBLY FOR EASY SET
®
POOLS WITH INFLATABLE TOP RINGS
1
NOTE: If you are using a METAL FRAME POOL, go to page 7.
Connect the skimmer
hose (16) to the
skimmer (10)
bottom connector.
2
Assemble the hook as shown. Adjust the opening of the hook (13) by
pressing and sliding the arm (14) at the same time.
Press
Press
Insert
Insert
Press
Slide
3
4
Loosen the skimmer
screw (11), attach the
assembled hook and hand
tighten the screw.
NOTE: Do not over
tighten or use tools
such as pliers.
Slide
Place the whole assembled
hook unit over the top of an
EASY-SET
®
Pool Top Ring near the
water outlet connector (lower hose
connection). Adjust the hook to be
snug around the
inflated ring
(see step #2).
Ensure
the hook is
securely
tightened
over the
pool.
10
13
14
12
11
16
Inflatable
Top Ring
13
14
12
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 7
HOOK ASSEMBLY FOR METAL FRAME POOLS
1
2
3
4
Connect the skimmer
hose (16) to the
skimmer (10)
bottom connector.
Assemble the hook as shown.
Loosen the skimmer
screw (11), attach the
assembled hook and hand
tighten the screw.
NOTE: Do not over
tighten or use tools
such as pliers.
Place the whole assembled
hook unit over the top of a
FRAME
Pool Top Beam near the
water outlet connector (lower hose
connection). Adjust the hook by
adjusting the two dove-tail screws, to
be tight on
the top beam.
Ensure the
hook is
securely
tightened
over the
pool top
beam.
10
16
Press
Press
Insert
Insert
12
15
Slide
11
Top Beam
15
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 8
SETUP INSTRUCTIONS
1
For pool size 16' (488 cm) and below:
Unscrew the strainer grid from the threaded strainer connector (lower)
from inside of the pool.
EASY-SET
®
POOL
METAL FRAME POOL
Lower Hose
Connection
Upper Hose
Connection
Threaded Strainer
Connector
Lower Hose
Connection
Upper Hose
Connection
Inside of the
Pool Wall
Inside of the
Pool Wall
Strainer
Grid
2
Depending on the size of pool purchased.
For 16' (488 cm) and below pools with strainer
17
Threaded
Strainer
Connector
a
b
16
17
Screw the hose adaptor B (17) to the
threaded strainer connector, from
inside of the pool.
Connect the other end of the
skimmer hose (16) to the
hose adaptor B (17).
a
b
For 18' (549 cm) and above pools with large strainer
17
Threaded
Strainer
Connector
16
17
Screw the hose adaptor B (17) to the
threaded strainer connector, from
inside of the pool.
Connect the other end of the
skimmer hose (16) to the
hose adaptor B (17).
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 9
SETUP INSTRUCTIONS (continued)
3
Place the basket (9), cover rim (7) and the floating cover (6) into the
skimmer (10). NOTE: the cover rim must be installed in place in order to
hold the Floating Cover in position.
EASY-SET
®
POOL
METAL FRAME POOL
6
7
9
4
The floating cover (6) should be floating off the skimmer (10) by 1" to 5"
(2.5cm to 12.7cm). Loosen the skimmer screw, slide the skimmer up and
down on the assembled hook to adjust the height. Hand tight the screw
when done.
1”- 5”
(2.5CM-12.7CM)
1”- 5”
(2.5CM-12.7CM)
EASY-SET
®
POOL
METAL FRAME POOL
IMPORTANT: The skimmer must stay vertical at all times, so that the top of the
floating cover can parallel to the water surface for skimming.
10
Inside of the
Pool Wall
Inside of
the Pool Wall
Inside of the
Pool Wall
Inside of the
Pool Wall
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 10
SETUP INSTRUCTIONS (continued)
• Set up the filter pump following the filter pump owner's manual. Turn on or
connect the filter pump to an electrical outlet.
5
WARNING
• Do not operate the filter pump while the pool is occupied or in use.
• Strong suction. Do not remove or obstruct the floating cover opening
while the filter pump is operating!
• Keep hands and hair away from the skimmer and floating cover
opening when the filter pump is operating!
• Turn off or unplug the filter pump before adjusting, cleaning, servicing
or removing the skimmer, basket or floating cover.
If no water is flowing into the pump, make sure that the surface skimmer
is perpendicular to the water surface and below the water surface. Open
the air release valve located on the filter housing top cover. When water
starts to flow out, close the air release valve back.
Never run the pump dry as the motor may overheat and damage the
pump!
IMPORTANT
• Remove the skimmer and the hook assembly from the pool before placing
a pool cover over the pool.
• Store the product and accessories in a dry and safe place indoors.
NOTE: On a weekly basis, remove the hose adaptor from the outlet fitting
connection to ensure the threaded strainer connector is free from debris, hair
and algae. Also make sure the cartridge in the lter pump is clean and there is
no leakage in the circulation system.
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 11
POOL VACUUM SETUP INSTRUCTIONS
1
2
3
Set up the surface skimmer by following the floating surface skimmer
manual. Turn off filter pump.
Remove the basket (9), cover rim (7) and the floating cover (6) from
the skimmer.
6
7
9
Place the debris bag (4) in the vacuum body (5). Press and hold the
clip on the vacuum body and close the vacuum cover (3) by turning
clockwise.
PRESS
3
4
5
2
1
3
4
5
4
Place the vacuum assembly into the skimmer, turn clockwise to connect.
3
3
5
10
10
16
16
1
2
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 12
POOL VACUUM SETUP INSTRUCTIONS
5
6
7
The handle adaptor (19) on the
vacuum head has a plastic spring
that connects to the end of the
handle. Align the plastic spring
located inside the vacuum head
with the holes drilled in the
handle. Gently squeeze together
the plastic spring tips so that
the handle slips onto the vacuum
head and the spring "pops" into
the pre-drilled holes.
18
19
20
27
2
1
1
With hose clamp, secure one
end of the vacuum hose (25) to
the hose connection on the
vacuum head. Make sure hose
clamp is tight.
25
26
18
Turn telescope A and clamp B counterclockwise and slide each
section to extend or shorten the length of the telescoping handle. Turn
clockwise to lock each section in place.
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 13
POOL VACUUM SETUP INSTRUCTIONS
8
9
Place pool vacuum into the water. Fill up the vacuum hose with water
by submerging the hose into the water to remove all of the entrapped
air from the hose. TIPS: Starting from the end of vacuum head,
submerge the vacuum hose vertically into the water, section by
section.
25
With hose clamp, fasten one end of the vacuum hose (25) to the
connection of vacuum head. Make sure hose clamp is tight.
25
26
3
10
16
• Release all the air from the hoses and filter pump before use.
• Keep the brush head under the water at all times during use.
• Remove the brush head assembly from the skimmer when running the
filter pump only and when the pool is not in use.
• Check and empty the debris bag regularly during and after each use.
IMPORTANT
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 14
POOL VACUUM OPERATING INSTRUCTIONS
POOL VACUUM SETUP INSTRUCTIONS
10
WARNING
• Do not permit children to use this product. Adult use only.
• Remove all maintenance items when the pool is in use.
The pool vacuum is now ready to use.
1. The filter pump is an airtight system. To eliminate air trapped in the hose or in
the pump, turn the top air release valve 1-2 turns in a counter-clockwise motion
to open the valve.
2. When water starts flowing out of the air release valve hole, screw in the air
release valve back into the filter housing cover. Do not over tighten the valve.
3. Connect the filter pump to the power outlet and turn ON the pump.
4. In soft gentle strokes "sweep" the entire bottom surface of the pool liner
until it’s clear of debris.
5. Make sure the filter pump is turned off, and disconnect the power cord
from the electrical outlet. Remove the pool vacuum from the pool.
6. Using the Set-Up instructions in reverse, disassemble the vacuum
cleaner. Clean the debris bag if necessary.
7. Store the pool vacuum in an area where it will not be a safety hazard.
If you experience low suction on the vacuum, check that all of the air has
been removed from the hose. If you still have a low suction problem, please
review the Troubleshooting Guide for your filter pump under "Filter pump does
not pump water or flow is very slow". Also, check that the debris bag is clean.
IMPORTANT
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 15
HAND-HELD SKIMMER ASSEMBLY & OPERATING INSTRUCTIONS
23
20
27
1. The hand-held skimmer uses the same handle as the pool vacuum.
2. The skimmer net (23) has a plastic spring (20) that connects to the end of handle. Align the
plastic spring located inside the net with the holes drilled in the handle. Gently squeeze
together the plastic spring tips so that the handle slips onto the net and the spring "POPS"
into the pre-drilled holes.
3. Gently sweep the surface of the pool with the skimmer net removing floating leaves, etc.
WARNING
• Do not permit children to use this product. Adult use only.
• Remove all maintenance items when the pool is in use.
HAND-HELD BRUSH ASSEMBLY & OPERATING INSTRUCTIONS
20
24
27
1. The hand-held brush uses the same handle as the pool vacuum.
2. The brush head (24) has a plastic spring (20) that connects to the end of handle. Align the
plastic spring located inside the brush head with the holes drilled in the handle. Gently
squeeze together the plastic spring tips so that the handle slips onto the brush head and the
spring "POPS" into the pre-drilled holes.
3. Gently sweep the entire side and bottom surfaces of the pool liner until it’s clear of debris.
WARNING
• Do not permit children to use this product. Adult use only.
• Remove all maintenance items when the pool is in use.
(97PO) DELUXE MAINTENANCE KIT ENGLISH SIZE: 4.875” X 7.25” PANTONE 295U 04/26/2020
97PO
S AVE THESE INSTRUCTIONS
Page 16
LONG TERM STORAGE
GENERAL AQUATIC SAFETY
1. Make sure the filter pump is turned off and disconnect the power cord from the
electrical outlet.
2. Using the Set-Up instructions in reverse, disassemble the floating surface
skimmer, pool vacuum, hand-held skimmer or hand-held brush.
3. Clean and air dry all the accessories and parts thoroughly.
4. The original packaging can be used for storage. Store in a dry, cool storage
location.
Water recreation is both fun and therapeutic. However, it involves inherent risks of
injury and death. To reduce your risk of injury, read and follow all product, package and
package insert warnings and instructions. Remember, however, that product warnings,
instructions and safety guidelines cover some common risks of water recreation, but do
not cover all risks and dangers.
For additional safeguards, also familiarize yourself with the following general guidelines as
well as guidelines provided by nationally recognized Safety Organizations:
• Demand constant supervision. A competent adult should be appointed as a “lifeguard” or
water watcher, especially when children are in and around the pool.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is supervising pool users about potential pool hazards and about the use
of protective devices such as locked doors, barriers, etc.
• Instruct all pool users, including children what to do in case of an emergency.
• Always use common sense and good judgement when enjoying any water activity.
• Supervise, supervise, supervise.
For additional information on safety, please visit
• TheAssociationofPoolandSpaProfessionals:TheSensibleWaytoEnjoyYour
Aboveground/Onground Swimming Pool www.nspi.org
• AmericanAcademyofPediatrics:PoolSafetyforChildrenwww.aap.org
• RedCrosswww.redcross.org
• SafeKidswww.safekids.org
• HomeSafetyCouncil:SafetyGuidewww.homesafetycouncil.org
• ToyIndustryAssociation:ToySafetywww.toy-tia.org
SAFETY IN YOUR POOL
Safe swimming depends on constant attention to the rules. The "NO DIVING" sign within
this manual can be posted near your pool to help keep everyone alert to the danger. You
may also wish to copy and laminate the sign for protection from the elements.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Intex 26377EH Owner's manual

26377EH
Intex
Brand
Intex
Model
26377EH
Category
Above ground pool accessories
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents