American Lighting LED-RGB-CTRL-24V Installation guide

Brand: American Lighting

Model: LED-RGB-CTRL-24V

Type: Installation guide

SAFETY INFORMATION

• Read all instructions before beginning. Save these instructions for future use.

• To reduce the risk of ﬁre, electric shock, or injury to persons, pay close attention to this

manual. Stay within its guidelines when using this product.

• All units must be unplugged before installing or servicing in any way.

• Do not route cords or units through walls, doors, windows, or any similar part of a

building structure.

• Do not use if there is any damage to the unit, its lens, and/or power cord’s insulation.

Inspect periodically.

• Controller housing is suitable for outdoor use (rated IP44), however when usign

outdoors, all power, DMX, and/or output connections must be properly sealed with shrink

tube and silicone and/or housed in a weather proof enclosure.

• Do not let the unit stand in water or liquid, nor locate where water can accumulate.

• Secure units with mounting hardware appropriate for the mounting surface. Do not

secure unit or its power cord with staples, nails, or like materials that may damage

insulation.

• Do not attempt to open or service this ﬁxture. None of its parts are seviceable by the user.

• This product has a polarized, grounded plug as a safety feature. Do not cut the plug o

or alter it in any way.

• Provide a grounded receptacle for within 5 feet of each ﬁxture’s location. If using

outdoors, outlet(s) must also be GFCI and weatherproof.

• Operating temperature must be between 20°C and 45°C (-4°F and 113°F). Avoid high

ambient temperatures.

• This controller requires the use of LED-RGB-15A-24V, 24V DC 15A power supply. Do not

operate this controller with any other power supply.

• Do not exceed more than 88ft of RGB-NF total on controller (maximum single run for

RGB-NF is 65ft)

These products may represent a possible shock or

ﬁre hazard if improperly installed or attached in any

way. Products should be installed in accordance with

these instructions, current electrical codes, and/or the

current National Electric Code (NEC).

When using this product outdoors, basic safety

precautions should always be followed to reduce the

risk of ﬁre, electric shock and personal injury including

the following:

• Ground Fault Circuit Interrupter (GFCI) protection

should be provided on the circuit(s) or outlet(s) to

be used for outdoor use. Receptacles are available

having built-in GFCI protection for this measure of

safety.

• Use only outdoor extension cords, such as type

SEW, SEOW, SEOOW, SOW, SOOW, STW, STOW,

STOOW, SJEW, SJEOW, SJEOOW, SJTW, SJTOW,

or SJTOOW. This designation is marked in the wire

of the extension cord. Never use with an extension

cord unless plug can be fully inserted.

WARNING

DMX RGB Controller for RGB-NF24V

INSTALLATION INSTRUCTIONS

LED-RGB-CTRL-24V

FIGURE 1

USING LED-RGB-CTRL-24V WITH RGB-NF:

LED-RGB-CTRL-24V requires the use of LED-RGB-15A-24V 24V DC power supply for operation. Disconnect power at the source prior

to operation.

1. Connect the DC “OUT” from LED-RGB-15A-24V to the DC “IN” on LED-RGB-CTRL-24V

2. Connect one of the included adapter cables to the Signal “OUT” on LED-RGB-CTRL-24

3. Follow the wiring guide on the adapter cable to connect to RGB-NF-CONKIT-NP

4. Follow mode instructions on page 2

LED-RGB-CTRL can be linked together by connecting the

Signal “OUT” from ﬁrst controller to the Signal “IN” on second

controller. When multiple controllers are used, provide each one

with a LED-RGB-15A-24V DC power supply. Do not exceed 65ft of

RGB-NF in a single run, nor 88ft from a single controller. When power

is applied, the default function is that the ﬁrst controller in the

series will become the master and the rest will become the secondary

followers. The state indicator display screen will display “H” for master

and “C” for secondary followers.

(A) DMX Out

(B) DMX In

(D) Signal Out

(E) Grounded power cord

(F) State indicator display

(G) Content level display

(H) Output indicator lights

(I) Power indicator light

(J) Mode select button

(K) Speed select button

DMX RGB Controller for RGB-NF24V

INSTALLATION INSTRUCTIONS

LED-RGB-CTRL-24V

BUILT-IN FUNCTIONS AND CORRESPONDING DISPLAY INDICATORS:

LED-RGB-CTRL-24V requires the use of LED-RGB-15A-24V 24V DC power supply for operation. Disconnect power at the source prior

to operation.

Use the “mode select” butotn to advance through modes D1-DA. When i nmodes D1-D7, using the “speed select” button will dim/brighten the

static color. When in modes D8-DA, using the “speed select” button will change the speed rate of the eect.

MODE

RESULT

Static Red

Static Green

Static Yellow

Static Blue

Static Purple

Static Blue-Green

Static White

7-Color Skip

7-Color Flash

7-Color Fade

SPEED BUTTON FUNCTION

Brightness: P1 = Dimmest, P6 = Brightest

Speed Rate: P1 = Slowest, P6 = Fastest

American Lighting LED-RGB-CTRL-24V Installation guide

American Lighting LED-RGB-CTRL-24V Installation guide

American Lighting LED-RGB-CTRL-24V Installation guide

Related papers

Other documents