SA21XTSA21XT
COLOUR TELEVISION
OPERATING
INSTRUCTIONS
2
◆Digital I C bus control
◆Auto search tuning & 250 programs stored
◆Full infrared remote control
◆Multi-Picture modes selection
◆Multi-function timer,appointing programme
0090505760
2
WARNING AND CAUTIONS
1. When you clean the TV set, please pull
out the power plug from AC outlet.
Or may result in electric shock, fire or
damage to the TV set. Don't clean the
cabinet and the screen with benzene,
petrol and other chemicals.
4. Do not place the TV set near rain
or moisture as it may cause an electric
shock, or the TV set to catch fire. The TV
set must only be used
in dry indoor location.
2. In order to prolong the using life of the
TV set, please place it at a well ventilated
location.
5. The back cover must only be removed
by a registered electrical service person.
Removing the back cover may result in
electric shock, fire or damage to
the TV set.
3. Don't place the TV
set in direct sunlight
or near heat source.
6. If the TV set is not going to be used for
a long time, or there is a severe thunder &
lightening storm, it is recommended that
the TV set be disconnected from the AC
power outlet and the aerial plug
removed.
Explanation on the display tube
When the picture tube requires cleaning, please disconnect the power and use a
dry soft cotton cloth. Do not use any cleaner or abrasive cloth.
1
CONTENTS
Contents..................................................................................................................................1
Warning and Cautions...........................................................................................................2
Basic Feature.........................................................................................................................3
Technical Specifications.........................................................................................................3
Preparing for Operations.........................................................................................................4
Function Buttons and External Sockets..................................................................................5
Remote Controller .................................................................................................................6
Control Your TV.....................................................................................................................7
Tuning Procedure.................................................................................................................10
Menu Operation...................................................................................................................11
Television Installation..........................................................................................................13
Connecting Other External Devices....................................................................................14
Trouble Shooting Guide...................................................................................................... 15
3
BASIC FEATURE
2
◆Digital I C bus control
◆Auto search tuning & 250 programs stored
◆Full infrared remote control
◆Multi-Picture modes selection
◆Multi-function timer,appointing programme
4
TECHNICAL SPECIFICATION
1.POWER SUPPLY: See rating plate
2.COLOUR SYSTEM: PAL SECAM N TSC4.43/3.58(AV)
3.AUDIO SYSTEM: B/G D/K
4.CRT: 21"
5.ANTENNA INPUT : 75Ω Standard Coaxial Cable
6.SOUND OUTPUT POWER: 3W+3W
7.POWER CONSUMPTION: See rating plate
8.NET WEIGHT(kg): 23.5
9.NET DIMENSION(mm): 610 x 475 x 465
Supplied accessories:
Infrared remote control handset 1
Battery(AA) 2
Operating instruction 1
Design and specifications are subject to change without notice.
FUNCTION BUTTONS AND EXTERNAL SOCKETS
2. The rear panel
1.Front Panel
(1)Remote sensor: let the remote
controller aim here, the TV set
can receive remote control signal.
(2)Power switch: press the button to turn
on the TV set ,press the button again to
turn off the TV set.
(3)Power indicator: the indicator lights
in standby status .The indicator glints
when you use remote controller.
(4)Menu button
(5) Program up/down button
(6)Volume up/down button
(7)TV/AV switch button
(8)Audio(R) input
(9)Audio(L) input
(10)Video input
MENU TV/AV
－ ＋ － ＋
P
(1)
(2)
(3)
(4)
(8) (9) (10)
(5)
(6)
(7)
REMOTE CONTROLLER
65
TV/AV Select
( P8)
Sound Volume
Up/Down
（Ref. P7 ）
Power/Standby
(Ref. P7 )
Program Up/Down
（Ref.
P7
.）
MENU
(Ref.P11.)
Mute
(Ref.P
8
)
Lock
(Ref.P9)
Call
(Ref.P8)
Direct Access Numeric
Keys
(Ref.P7)
Quick View
(Ref.P8)
ZOOM
(Ref.P7)
Picture Effect
(Ref.P9)
?
-/--
2
1
3
4 5 6
7
8
9
0
QV
TIMER
SOUND
V+
V-
P+
MENU
P-
PIC
TV/AV
Picture MENU
(Ref.P11)
Time MENU
(Ref.P12)
Sound MENU
(Ref.P11)
Re
f
.
INPUT AND OUTPUT TERMINALS
It can be connected to the following appliances:
video-tape recorder, video camera, tape recorder
and audio amplifier, etc......
*Please keep AC cord unplugged when connecting
TV system.
You can select your video source by the [TV/AV] key.
EURO
7. MUTE
By pushing this key, sound
output will be muted.
Push [MUTE] again or Volume
Up/Down, and sound Volume
will return.
8. Quick View
Program will quick back
to the previous program
being watched.
9. CALL
Program No.
Colour system
Clock
Sleep
TV/AV MODE
This key will call the on
screen display.
Push again to remove the
on screen display.
Menu MODE
Pressing the [?]key,
current menu will
exit directly.
7 8
TV/AV
3
EURO
AV
3
or
6. TV/AV Selection
MUTE
QV
10
2
AV
TV
?
1
PAL
B/G
15:15
SLEEP 120
CONTROL YOUR TV
1. Power/Stand-By ON/OFF
With Mains status On, you can also turn off using Remote
Control Hand Set.
This status is called Stand-By mode. In this mode, You
can also turn on the
TV by pushing the Channel UP/Down
keys on the front controls.
There is an Automatic Power OFF function in the TV. With No
Signal condition,
the TV will automatically turn off after 10 minutes.
2.
Program Up/Down
Push [P+] key to change Program Up.
Push [P-] key to change Program Down.
CONTROL YOUR TV
3
2
1
1
VOLUME 15
|||||||------------
V-
V+
P+
MENU
P-
-/--
2
1
3
4 5 6
7
8
9
0
V- V+
P+
MENU
P-
3.
Direct Access Tuning
Using the numeric keys on Remote
Control Hand Piece, channel can be
selected directly from 0 to 249 channels.
Or repeatedly press the -/-- button to
select the desired mode then press numeric buttons.
“-” 1 digit mode
“ ”-- 2 digit mode
“--- ” 3 digit mode(Max Ch. 249)
Volume Control
Push [V+] key for Volume Up.
Push [V-] key for Volume Down.
ZOOM
Push [ZOOM] key to change as follows:
NORMAL WIDE ZOOM
W ID E picture height is reduce, ZOOM picture height is expand.
__
4.
__
5.
“ ”
9
CONTROL YOUR TV
10. Picture Effect
By repeatedly pushing this key, picture effects will change
as follows.
DYNAMIC USER
MILD STANDARD
TINT setting is not included user is the last
setting made by
you.
11. LOCK
By pushing the [ ] key, ----
will appear on the screen.
Pressing the password the
digits that you defined yourself
correctly, the lock menu will appear.
A. Select each function using the
[P+] [P-] keys.
B. Each value can be changed by the
[V+] [V-] keys.
C. When general lock is on, other locks
may be locked.
D. Child lock will be locked or unlocked
for current program.
E. AV LOCK will be locked or unlocked
for AV function.
F. VOL LIMIT SW will be switched on or off.
G.When you will change the password, you may be selected
NEW PASSWORD item, then push [V+] [V-] keys, the
CHANGE PASSWORD menu will appear
NEW PASSWORD: input 4 digits you like.
CONFIRM: again input above new password 4 digits correctly.
H. Press the [ ] key or [?] key, lock menu will disappear.
Note:
The tune menu will not appear when any program would be locked.
After new password was set, the basic password 7038 still is available.
STANDARD
“ ”
CHANGE PASSWORD
NEW PASSWORD 0 0 0 0
CONFIRM - - - -
LOCK
GENERAL LOCK ON
PROGRAM NO. 25
CHILD LOCK ON
AV LOCK ON
VOL LIMIT SW ON
VOL LIMIT ON
CHANGE PASSWORD 32
- -- -
TUNING PROCEDURE
1. Auto Search Function: Automatic Search and Memory (ASM) is available
for program installation from Antenna input.
Using [MENU] key on the front or
[MENU] key on the Remote for ASM.
A. Push [MENU] key repeatedly to
select TUNE.
B. Push [P+] or [P-] key to select
AUTO SEARCH.
C. Push [V+] or [V-] key to start ASM
and memorize into program list(0~249).
D. Wait until function has finished.
2. SEARCH Function: Manual Search for Antenna input.
A. Push [MENU] key repeatedly to select TUNE.
B. Using [P+] or [P-] key, select PROGRAM. Using [V+] or [V-] key or numeric
keys to change Program Number.
C. Push [P+] or [P-] key to select BAND. Push [V+] or [V-] key to
change BAND.
D. Push [P+] or [P-] key to select SEARCH.
E. Push [V+] or [V-] key to start search.
F. Wait until function has finished.
G. Push [P+] or [P-] key to select STORE. Push [V+] or [V-] key to
store.
3. FINE TUNING Function: Fine Tuning for current setting.
A. Push [MENU] key repeatedly to select TUNE.
B. Using [P+] or [P-] key to select PROGRAM. Using [V+] or [V-] to change
Program Number.
C. Using [P+] or [P-] key to select FINE TUNE.
D. Using [V+] or [V-] key to adjust for best tuning.
E. Push [P+] or [P-] key to select STORE. Push [V+] or [V-] key to store.
4. SKIP Function: Use to SKIP channels. After setting to ON, the channel will
not be selected by Channel Up/Down keys.
A. Push [MENU] key repeatedly to select TUNE.
B. Using [P+] or [P-] key to select PROGRAM. Using [V+] or [V-]
key to change
Program Number.
TUNE
BAND UHF
SKIP OFF
PROGRAM 3
SEARCH
FINE TUNE
STORE
AUTO SEARCH
10
MENU OPERATION
EXCHANGE
PROGRAM1 10
PROGRAM2 14
EXCHANGE
11 12
5. EXCHANGE Function: number and channel exchange.
A. Push [MENU] key repeatedly to select EXCHANGE.
B. Using [P+] or [P-] key to select
PROGRAM 1. Using [V+] or [V-]
key to change Program 1 Number.
C. Using [P+] or [P-] key to select
PROGRAM 2. Using [V+] or [V-]
key to change Program 2 Number.
D. Using [P+] or [P-] key to select
EXCHANGE. Using [V+] or [V-] key,
exchange is over.
MENU OPERATION
1. [MENU] key
Push [MENU] key continually to scroll through the MENU selection as
follows:
PICTURE SOUND TIME SETUP TUNE EXCHANGE
2. PICTURE MENU Function: Brightness, Contrast, Colour, Sharpness, Tint
A. Select each function using the [P+]
or [P-] key.
B. Each value can be controlled by the
[V+] or[ V-] key.
C. Repeat any functions if required.
NOTE: TINT control will be appeared
only if a NTSC signal is being
received.
3. SOUND MENU Function: Volume
A. Press SOUND menu, the volume will appear.
B. Each value can be controlled by the [V+]or [V-]
key .
C. Using [P+] or [P-] key to select SKIP. Using [V+] or [V-] key to
select ON or OFF.
PICTURE
BRIGHTNESS 48
CONTRAST 48
COLOUR 32
SHARPNESS 32
TINT
SOUND
VOLUME 20
TIME
CLOCK --:--
ON TIME --:--
ON PROG 2
OFF TIME --:--
SLEEP TIMER 0
REMIND TIME --:--
REMIND PROG 1
4. TIME MENU Function: Time and Timer setting
A. Select TIME with the [MENU] key.
Using the [P+] or [P-] key to select
the item.
B. Using the [P+] or [P-] key to select
CLOCK, ON-TIME, OFF-TIME,
SLEEP TIME or REMIND TIME.
C. Press [P+] or [P-] key to select minutes,
then using [V+] or [ V-] key, minutes
will change from 00 to 59. Press [P+] or
[P-] key to select hours, then using
[V+] or [ V-] key, hours will change
as follows: 0,1,..23--:--.
D. For ON-TIME, OFF-TIME or
REMIND TIME setting, using [P+]
or [P-] key to select ON PROG,
using [V+] or [ V-] key to change
On-Program number.
E. Using [P+] or [P-] key to select
SLEEP TIME, Using [V+] or [ V-] key,
sleep timer will change as follows:
0 10 20 30 40 ...160 170 180 0
5. SETUP Function: other function setting.
A. Using the [P+] or [P-] key to select
the item.
Using the [V+] or [V-] key to change
the item.
B. Using the [P+] or [P-] key to select
the LANGUAGE.
Using the [V+] or [V-] key, language
will change as follows:
ENGLISH ARABIC PERSIAN TURKISH FRANCE RUSSIA
C. Using the [P+] or [P-] key to select the COLOR SYS.
Using the [V+] or [V-] key, color system will change
as follows:
AUTO PAL NTSC3.58 NTSC4.43 SECAM
MENU OPERATION
SETUP
LANGUAGE ENGLISH
COLOR SYS AUTO
SOUND SYS DK
BLUE BACK ON
BLACK STRETCH ON
AVL ON
EURO RGB
CALENDAR
GAME1
GAME2
13
TELEVISION INSTALLATION
Connect antenna or video facility
1. Use 75 coaxial cable plug or 300-75 impedance converter to plug in antenna
input terminal on the rear of the cabinet.
2. Connect the video facility to the radio, video in jack on the rear of the cabinet.
Battery installation and replacement for remote control unit
The remote control uses two 1.5V AA
batteries. For installation and replacement
are as following:
1 Turn the remote control unit upside
down. Press down the grip of battery
compartment and slide the color in
the direction of the arrow.
2 Install two new batteries, make sure
that battery polarity matches with the
+,- marks inside the battery. Or not it
could damage the unit.
3 Close the battery compartment covers.
14
-
VHF antenna
UHF antenna
Mixer
75 Co-axis cable
Input terminal of antenna
Co-axis antenna plug
Antenna in jack
75 Co-axis antenna plug
- - - - - - - - - - - - - - -
D. Using the [P+] or [P-] key to select
the AVL, AVL is auto volume level.
Using the [V+] or [V-] key, AVL will
be turned OFF and ON.
E. Using the [P+] or [P-] key to select
the CALENDAR.
Using the [V+] or [V-] key,
CALENDAR will appear.
After CALENDAR is appeared on the
screen:
Using the [P+] or [P-] key to change
the month.
Using the [V+] or [V-] key to change
the year.
F. Using the [P+] or [P-] key to select the GAME1 or GAME2.
Using the [V+] or [V-] key, GAME will be appear.
In game 1 mode, input digit by digit key direction. Until same
number is 4, same position 4.
Push [MENU] key to start game again.
Push [?] key to exit game.
In game 2 mode, the box will be moved to specific dot.
Push [P+] or [P-] key to move the box for up or down.
Push [V+] or [V-] key to move the box for right or left.
Push [?] key to exit game.
- - - - - - - - - - - - - - -
- - - - - - - - - - - - - - -
- - - - - - - - - - - - - - -
2004 1
Su Mo Tu We Th Fr Sa
1 2
3
4
5
6
7
8
9 10
11 12
13
14
15 16 17
18 19 20
21 22
23
24
25 26 27
28 29 30 31
MENU OPERATION
TROUBLE SHOOTING
Before arranging for service, firstly know the status and then check simply as follows:
Problems Check
No picture or sound
Check if the power supply is plugged in.
Check if the power switch is in ON position.
Picture is OK, no sound
Check if the volume control is set to the
minimum or mute position
Check there are no obstacles between the
sensor window and remote control unit.
No TV signal
Check if the TV/AV button is not set to TV
status.
Check if the antenna is well connected.
Check if you installed the TV correctly.
No external video signal
Check if you installed the TV correctly.
Check if the TV/AV button is set to AV
position.
All channels lose colour
intermittently
Check if the antenna is broken.
Poor reception, loss of
colour with certain
channels
Check if channels are correctly Tuned ( see
Fine Tuning).
Diagonal stripes appear
on picture
The receiver may be affected by interference
(e.g. from nearby radio broadcasting
transmitter or from another TV receiver).
Picture has snow
Check if the antenna is broken.
Check if the antenna is disconnected.
Check if the antenna is damaged.
Ghost images appear
Check if the antenna direction has been
changed by a storm or strong wind, etc.
(because ghost images are caused by the
arrival at the antenna of both the signal
which has traveled directly from the
transmitter and the signal which has been
reflected from a hill or a large building. The
direction of the antenna should be chosen for
minimized ghosting.)
Remote control does not
work
Check if the power switch is in ON position.
Check if the batteries are out of use or not
connected well.
Make sure that there is no strong light
striking the sensor window or remote control
unit
Check if the antenna is disconnected.
Check if the antenna is damaged.
lacks colour or
picture too dark
Picture
Check colour, brightness
controls are correctly
and contrast
adjusted.
16
15
CONNECTING OTHER EXTERNAL DEVICES
To connect signal from the player,
scart-cable would be connected
correspondingly. The device may
be to provide RGB or VIDEO or
Y/C output, you must change
EURO signal setting
correspondingly on setup menu.
SETUP
LANGUAGE ENGLISH
COLOR SYS AUTO
SOUND SYS DK
BLUE BACK ON
BLACK STRETCH ON
AVL ON
EURO RGB
CALENDAR
GAME1
GAME2
VCR or DVD player or other
device for playing
/