36W
2160 LUMENS 12 CREE LED
COMBINATION LIGHT BAR
*Actual product may vary slightly
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.
Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property
damage and/or personal injury. Please keep instructions for future reference.
For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.
For Customer Service, Call 1-800-348-5004
or e-mail [email protected]
35710 03/2017
This product contains or, when used, produces a chemical
known to the State of California to cause cancer and birth
defects or other reproductive harm.
(California Health & Safety Code § 25249.5, et seq.)
WARNING
TECHNICAL SPECIFICATIONS
Bulb Type 3W CREE® LED
Bulb Qty. 12pc
Voltage
10-30V
Beam Type Combination (Spot/Flood)
Watts
36W
Lumen
2160 LM
Color Temperature
6500k
Operating Temperature -40°F to +145°F
10.276in.
3.740in.
4.173in.
92.0°
2
1-800-348-5004
WARNING
Please check your state and local laws before installing this LED off-road product. Every state/province
has different policies and procedures in place regarding aftermarket vehicle accessories.
The installation is recommended to be performed by a licensed professional. Please read the following
instructions thoroughly before installing this LED Light Bar.
LIGHT BAR USE AND CARE
1. Do not shine directly into your eyes.
2. Slowly tighten end cap bolts, do not over-tighten, stop when lock washers are flattened.
3. Do not turn on light during assembly; it may damage the light.
MOUNTING THE LED LIGHT BAR
1. Prior to installation, inspect and check the operation of this LED Light Bar to ensure that it is functioning
properly. Simply connect the Red power wire to the Positive (+) terminal on the battery and then connect
the Black wire to the Negative (-) terminal on the battery or to any other good unpainted ground source.
2. Using the included 5/16" x 9/16" screws, attach each mounting bracket to both ends of the LED Light Bar
and tighten with a 6mm Allen or hex key.
3. Identify the area where you would like to mount your LED light bar. Using the included 5/16" x 1-9/16"
screws, bolts and rubber washers, securely mount the light bar to your vehicle (Please measure carefully
before mounting).
POWERING THE LED LIGHT BAR
Note 1: Before installation, make sure to disconnect the battery for safety.
Note 2: If this light bar is directly connected to a battery, a toggle switch is needed to turn the light on/off,
as well as an in-line fuse within 12 inches of the power source.
Note 3: When you are extending the lead power wires to the light bar, it is highly recommended to solder
the connection and then to heat-shrink over the soldered connection (these materials are not included
– but they are available at most hardware or auto part stores.)
1. Connect the RED power wire to the positive output post of the toggle switch and run the appropriate
gauge wire (18 gauge at a minimum) from the input post of the toggle switch to positive (+) terminal
on the battery.
NOTE: Be sure to install the appropriate fuse (10A) for your light bar within 12 inches of your power source.
2. Next, connect the ground wire to the negative (-) terminal on the battery or any other good bare metal
ground source.
3. You can now flip the toggle switch to the "on" position to test your LED light bar for full functionality.
CAUTION
1. Work under the specified voltage DC10-30V.
2. The light becomes hot under continuous use. Don't remove or touch the casing for at least 30 minutes
after turning lamp off.
3. Keep heat-sink fins clean and free of debris to maintain air flow.
3
1-800-348-5004
Limited Manufacturer Warranty
FOT makes every effort to ensure that this product meets high quality and durability
standards. FOT warrants to the original retail consumer a 1-year limited warranty
from the date the product was purchased at retail and each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly
to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of
maintenance. FOT shall in no event be liable for death, injuries to persons or
property, or for incidental, special or consequential damages arising from the
use of our products. To receive service under warranty, the original manufacturer
part must be returned for examination by an authorized service center. Shipping
and handling charges may apply. If a defect is found, FOT will either repair or
replace the product at its discretion.
DO NOT RETURN TO STORE
For Customer Service:
Email: [email protected] or Call 1-800-348-5004
4
1-800-348-5004
/
