Kyosho 11009 User manual

Brand: Kyosho

Model: 11009

Category: Toys & accessories

Type: User manual

This manual is also suitable for

CURTISS P40 WARHAWK(No.11009)

Kyosho 11009 is a radio controlled engine powered scale aircraft, designed for intermediate and advanced flyers. It has a wingspan of 1422mm and requires a 4-channel or 5-channel radio control system for operation. The model comes with a detailed instruction manual that guides the user through the assembly and operation of the aircraft. It includes information on the required tools and materials, as well as safety precautions to be taken during assembly and operation.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

No.11009

REQUIRED FOR OPERATION

BEFORE YOU BEGIN

ASSEMBLY

OPTIONAL PARTS

OPERATING YOUR MODEL SAFELY

WINGSPAN: 1422mm

SAFETY PRECAUTIONS

This radio control model is not a toy!

For Intermediate

Advanced Flyers.

THE FINEST RADIO CONTROL MODELS

INSTRUCTION MANUAL

3~14

15~16

RADIO CONTROLLED ENGINE POWERED SCALE AIRCRAFT

KYOSHO SQS WARBIRD SERIES

Before commencing assembly, please read these instructions thoroughly.

INDEX

First-time builders should seek the advice of experienced modellers

before commencing assembly and if they do not fully understand

any part of the construction.

Assemble this kit only in places out of children s reach!

Take care before operating this model.

You are responsible for this model s assembly and safe operation!

Always keep this instruction manual ready at hand for quick

reference, even after completing the assembly.

Sharp Hobby Knife

Phillips Screwdriver (L, M, S)

Needle Nose Pliers

Awl

Scissors

Wire Cutters

REQUIRED FOR OPERATION (Purchase separately!)

TOOLS REQUIRED (Purchase separately!)

A minimum 4 channel radio control

system for aircraft

3 12

12 AA-size batteries,

either dry cell or NiCd.

Read instruction manual supplied with radio control system thoroughly before use.

For retract gear, you will need 5 channel radio, 1 retract servo,

1 extension cord.

AAAA

Model Aircraft Engine

Muffler

Engine and Muffler

Glow Plug

Extension Lead x 2

(200mm)

Y- Harness x 1

Purchase a propeller that

will suit your engine.

Propeller

CAUTION

For details concerning the equipment listed below

(size, maker, etc.), check with your hobby shop.

CAUTION

:Only use radio control systems designed for  

aircraft.

2 40 ~ 46

4 52 ~ 53

2 Stroke .40 ~ .46

4 Stroke .52 ~ .53

Propeller

Fuel Tube

Double Side Tape

Shock Protecting Foam

This model will require a minimum 4 channel radio control

(with 5 standard servos) for aircraft, if having fixed

undercarriage, or 5 channel radio (with 6 standard servos),

if fitting retractable undercarriage.

One-touch Plug Heater Set

Required for engine starting:

Fuel Bottle

Plug Wrench

Model Glow Fuel.

MODE

NGINE

FUEL

SILICONE

Epoxy A

Epoxy B

Instant Glue

(30 )

Epoxy Glue (30 minute type)

Silicone Glue

Glue

WARNING: Never use petrol /

gasoline with glow

engines.

Engine Starter

12V

12V Battery (for starter)

Other equipment for enhancing aircraft operation & performance

For retracting landing gear.

Fuel Filter

Retracting Landing Gear

Rod and screw

Muffler extention

adapter (2 Stroke)

Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.

Symbols used throughout this instruction manual comprise the following:

Main Wing

Apply epoxy glue.

Assemble left and right

sides the same way.

Must be purchased separately!

2mm

Drill holes with the specified

diameter (here: 2mm).

Cut off shaded portion.

2mm

Cut off excess.

Apply instant glue

(CA glue, super glue).

Ensure smooth non-binding

movement while assembling.

Do not overlook this

symbol!

Pay close attention here!

Warning!

Align the center line of

main wing with aileron.

Main Wing

BEFORE YOU BEGIN

Read through the manual before you begin, so you will have an overall idea of what to do.

Cut away covering

film only.

Feel for edges of

the holes underneath

of the film.

View from Underside of Main Wing

Secure aileron hinges with instant glue,

being careful not to glue the wing and

aileron together.

2 x 22mm

Screw

2 x 6mm

Screw

Adjust the travel of each control surface.

Please refer to .

Warning!

3mm

Set Screw

2 x 6mm

3mm

Apply epoxy glue.

Assemble left and right sides

the same way.

Must be purchased separately!

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

Main Wing

2 x 6mm TP

TP Screw

Fix the screws securely.

Failure in flight will cause your model to crash.

Do not disregard this symbol!

Warning!

Included with the radio set.

Aileron Servo

2 x 22mm

2mm

2 x 6mm

1mm

Note, P13 24 P.14 29 , if you use retracting landing gear.

Ensure that the two wing halves are securely

glued together.

Warning!

P.13 24P.1429

Note, P13 24 P.14 29 , if you use retracting landing gear.

P.13 24P.1429

Note, P13 24 P.14 29 , if you use retracting landing gear.

P.13 24 P.14 29

Stopper (L)

3mm

Set Screw

Main Wing

Cut away covering film only.

Apply instant glue

(CA glue, super glue).

Feel for edges of

the holes underneath

of the film.

Apply epoxy glue.

Assemble left and right sides

the same way.

Cut off shaded portion.

Main Wing

Do not disregard this symbol!

Warning!

A’

A = A’

Main Wing

Cut away only covering film.

Align with main wing holes.

Engine Mount

Align lower face of engine

mount arm on "Crankshaft

Center line".

4 x 20mm

Cap Screw

Crankshaft Center Line

4mm

Blind Nut

4 x 35mm

Cap Screw

4mm

Washer

4mm

Blind Nut

4x20mm

4mm

4x20mm

Apply instant glue

(CA glue, super glue).

4.1mm

4mm

Apply epoxy glue.

Must be purchased separately!

2mm

Drill holes with the specified

diameter (here: 2mm).

Cut off shaded portion.

2mm

Pay close attention here!

Fuel Tank

3x18mm

5mm

After confirming the position

(see front view of fuel tank),

insert and tighten the screw.

Fix with silicone glue.

3 x 18mm

Screw

Engine Mount

Throttle Rod

117mm

3 x 30mm

Screw

3mm

Washer

3mm

Nut

3.1mm

Apply epoxy glue.

Must be purchased separately!

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

Depends on the position

of the throttle arm.

Engine Mount

Washer

3mm

3 x 25 mm

Nut

3mm

Engine

4mm

A = AÕ B = BÕ

C = CÕ

Warning!

Ensure that the horizontal stabiliser is

securely glued to the fuselage.

Cowling

2 x 10mm TP

TP Screw

2 x 10mm

3 x 16mm

3 x 16mm TP

TP Screw

Horizontal / Vertical Tail

Cut off the cowling in

the way of the engine.

1mm

2 x 10mm

Ensure that the horizontal

stabiliser is securely glued

to the fuselage.

AÕ

BÕ

CÕ

Apply included decals to nose cowl side. For the correct location of decals, plese refer to the box top.

Secure elevator hinges with instant glue,

being careful not to glue the elevator

to the horizontal stabiliser.

3mm

1mm

Apply epoxy glue.

2mm

Drill holes with the specified

diameter (here: 2mm).

Cut off shaded portion.

2mm

Pay close attention here!

Do not disregard this symbol!

Warning!

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(CA glue, super glue).

Assemble left and right sides

the same way.

Stopper (S)

3mm

Set Screw

2 x 10mm TP

TP Screw

Warning!

1mm

To servo .

To elevator horn.

Rudder / Elevator Rod

To servo.

To rudder horn.

2mm

Heat-shrink Tube

Slide heat shrink tubes over linkage rods and use

a hair dryer or similar to secure (shrink) them in place.

Be careful not to scorch the

heat-shrink tube!

Bend at end of rod.

Rudder / Elevator Rod

2mm

Stopper (S)

3mm

2 x 10mm

Secure rudder hinges with instant glue,

being careful not to glue the rudder

to the vertical fin.

To elevator horn.

To rudder horn.

300mm

100mm

Ensure that the Vertical Fin is securely glued to the fuselage.

Apply epoxy glue.

Must be purchased separately!

Assemble as many times as

specified (here:twice).

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

Vertical Fin

Pay close attention here!

Apply instant glue

(CA glue, super glue).

Do not disregard this symbol!

Warning!

Rudder horn

2 x 14mm

Screw

2 x 14mm

Screw

2 x 6mm

Screw

3mm

Set Screw

2mm

Drill holes with the specified

diameter (here: 2mm).

2mm

2 x 6mm

Cut off shaded portion.

Horizontal Stabiliser

Vertical Fin / Rudder

Horizontal Stabiliser

Vertical Fin / Rudder

2 x 6mm

Screw

3mm

Set Screw

2mm

2 x 14mm

Cut away film

and balsa.

2 x 6mm

3mm

100mm

30mm

2mm

Cut off excess.

Elevator horn

2 x 14mm

100mm

50mm

Cut away film

and balsa.

2 x 6mm

3mm

Elevator rod

Rudder rod

2 x 6mm TP

TP Screw

Must be purchased separately!

2mm

pecified

diameter (here: 2mm).

Cut off shaded portion.

2mm

Radio Equipment

Pay close attention here!

3mm

Set Screw

2mm

Washer

(B)

Linkage Stopper (B)

2mm E

E-ring

Canopy

Ensure smooth non-binding

movement while assembling.

Throttle Servo

Elevator Servo

Rudder Servo

Battery / Receiver

95~105mm

3mm

2mm

E-ring

2mm

Paint the canopy frame in black.

2 x 6mm

1mm

Assemble left and right sides

the same way.

Apply epoxy glue.

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according

to your requirements and flight experience.

12 mm

30 mm

10 mm

RUDDER

ELEVATOR

AILERON

30 mm

Rudder Control.

Elevator Control.

Aileron Control.

Pay close attention here!

Retract Servo

Included with the radio set.

Retractable Gear

167mm

3 x 16mm

Screw

Eyelet

L Crank

3mm

Washer

3 x 16mm

Eyelet

Washer

Apply epoxy glue.

Assemble left and right sides

the same way.

Must be purchased separately!

Cut off shaded portion.

80mm

75mm

A retractable landing gear system is not included in this kit and must be purchased separately.

To install retractable undercarriage, a minimum 5 channel radio with 1 additional retractable

gear servo and 1 extension cord is required.

View from Underside of Main Wing

Cut out the outline of wheel well to

a diameter of 80mm. Cut out the wheel

well inserts shown in Section first,

and use them as a guide when cutting

wheel well recesses to ensure that you

do not cut holes oversize.

View from Top Side of Main Wing

40mm

45mm

3mm

Set Screw

2mm

Washer

(B)

Linkage Stopper (B)

2mm E

E ring

40mm

Pay close attention here!

RETRACTABLE GEAR (PURCHASE SEPARATELY)

Cut off excess.

Bend wire for smooth operation.

Make sure linkages for landing gear are properly locked.

If linkage rods foul, bend accordingly to ensure

free movement.

Remove shaded area.

Assemble left and right sides

the same way.

Cut off shaded portion.

Pay close attention here!

Apply instant glue

(CA glue, super glue).

Retractable Gear

View from Underside of Main Wing

Nylon Propeller

P.P. Pipe

300

Fuel Tube Stopper

Polipropylene Pipe

200

90469

91490

90410-06

D10 x P6 Nylon Propeller

Nylon Propeller

D11 x P7

550

650

D10 x P8

D10 x P7

550

D11 x P8 650

90411-07

90410-08

90410-07

90411-08

D12 x P6 750

750

90412-06

D12 x P8

90412-08

OS52 (UNF 1/4 - 28)

Adopter nut. For OS.52

350

YS53 (M6)

Adopter nut. For YS.53

350

6000

90487-05

90487-06

90081

PARTS

No. Part Names Quantity

11009-01

90424-70

Cowling

Scale Spinner(70mm)

1 2500 200 200

200

11009-03

Main gear

( L.R ) 1500

700

No. Part Names

:FOR JAPANESE MARKET ONLY.

Quantity

:FOR JAPANESE MARKET ONLY.

11009-02

Canopy

1 11500

OPTIONAL PARTS

No. Part NamesNo. Part Names

 This model aircraft is designed for Intermediate to Experienced fliers. Beginners should seek advice for pre-flight adjustments

and assembly from more experienced fliers. Be aware that flying a badly assembled or badly adjusted aircraft is very

dangerous!

 At the start, first-time fliers should always be assisted by an experienced flier and NEVER fly alone!

 This model aircraft is designed to be powered by either a 2 stroke .40 ~ .46 size engine or a 4 stroke .52 ~ .53 size engine.

 Installing a more powerful engine than specified or flying this model dangerously could lead to serious injury and/or damage

to property.

Do not overlook this symbol!

Warning!

0 0 2 1 0 4 4 7 2 7 1

1 6 8 0

0 0 2 1 0 4

4 7 2 7 1

1 6 8 0

1,400

200

1,680

(1)

(2)

(3)

(4)

(1)

11009

OFF

Before Flying

Before flying your airplane, ensure

the airfield is spacious enough.

Always fly it outdoors in safe areas

with no debris or obstacles!

For handling the radio properly,

refer to its instruction manual.

Ensure the spinner and propeller are

securely attached.

If your airplane begins to operate by

itself, there is another transmitter on

your frequency. Immediately stop

your airplane; otherwise you may

lose control of it which will result in

accidents.

Fully extend

the transmitter

antenna.

Switch on the transmitter.

Switch on the receiver.

Ensure the wings are securely

attached.

Flying

Fill the fuel tank.

By moving the control sticks, ensure

all control surfaces moves as per

your adjustments.

For starting the engine, apply low

throttle and hold the engine starter

against the spinner.

Adjust the needle.

After Flying

Only use KYOSHO genuine parts!

Cautions for Safety

Adjust the engine always from behind,

but never from infront or the sides as

a rotating propeller may badly injure

you!

Do not allow watching people to get

too close to a rotating propeller.

Immediately disuse defective pro-

pellers as well as deformed spinners.

If the dry batteries in the radio are

flat, replace them with fresh ones.

Do not fly your airplane above people

standing around.

Hand-launch your airplane into the

wind to make it take off.

Do not fly your airplane when there

is a strong wind or a lateral wind.

Always land your airplane into the

wind.

Bring your airplane to a halt by

lowering the throttle trim.

After each flight, the engine is very

hot. Beware of getting burned!

Wipe away any fuel deposits or dirt.

Never throw burning, gleaming or

smouldering things into fuel cans,

even if these happen to be empty.

This will result in serious injury!

WIND

OFF

OFF ON

Switch off the receiver.

Switch off the transmitter.

OFF

Draw out the remaining fuel from the

fuel tank and fill it back into the can.

By moving the throttle control

stick, ensure the carburetor opens

and closes without effort.

THE FINEST RADIO CONTROL MODELS

85290103-1 PRINTED IN CHINA

Always do observe the following in order to prevent accidents!

FLIGHT MANUAL

Warning!

Kyosho 11009 User manual

Brand: Kyosho

Model: 11009

Category: Toys & accessories

Type: User manual

This manual is also suitable for

CURTISS P40 WARHAWK(No.11009)

Download PDF

report

in other languages

日本語: Kyosho 11009 ユーザーマニュアル

Kyosho 11009 User manual

This manual is also suitable for

Kyosho 11009 User manual

in other languages

Related papers

Other documents