Bel Air Lighting PL-50491 BK User manual

Bel Air Lighting
Brand
Bel Air Lighting
Model
PL-50491 BK
Type
User manual

Bel Air Lighting PL-50491 BK is a lighting fixture that requires assembly before use. It is designed to be installed on a ceiling and can be used in various rooms of your home. The fixture comes with a 2-year limited warranty.

The fixture uses a 1-26 GU24-base bulb which is included with the purchase. It also has a chain that can be adjusted to the desired length, allowing you to customize the height of the fixture.

To install the fixture, you will need to turn off the power to the circuit breaker or fuse panel. Then, remove the old fixture and disconnect the wiring. Next, attach the mounting strip to the junction box using outlet box screws. Adjust the chain to the desired length and attach it to the fixture loop and screw collar loop.

Bel Air Lighting PL-50491 BK is a lighting fixture that requires assembly before use. It is designed to be installed on a ceiling and can be used in various rooms of your home. The fixture comes with a 2-year limited warranty.

The fixture uses a 1-26 GU24-base bulb which is included with the purchase. It also has a chain that can be adjusted to the desired length, allowing you to customize the height of the fixture.

To install the fixture, you will need to turn off the power to the circuit breaker or fuse panel. Then, remove the old fixture and disconnect the wiring. Next, attach the mounting strip to the junction box using outlet box screws. Adjust the chain to the desired length and attach it to the fixture loop and screw collar loop.

ITEM NO: PL-50491
ITEM NO: PL-50491
CAUTION
:This lamp is partially assembled in the factory
by qualified craftsmen.Some assembly is required
before use.Please follow the assembly instructions carefully.
IMPORTANT: Before you start,
NEVER
attempt any work without shutting off the electricity until the
work is done.
a) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch
in the "OFF" position.
b) Unscrew the fuse(s), or switch "OFF" the circuit breaker switch(s), that control the power to
the fixture or room that you are working on.
c) Place the wall switch in the "OFF" position. If the fixture to be replaced has a switch or pull chain,
place those in the "OFF" position.
PREPARATION
PREPARATION
1. Shut off main power at the circuit breaker or fuse panel before removing old fixture.
2. Remove old fixture Disconnect wiring.
FIXTURE INSTALLATION
1. Fix the nipple(G) with hex nut (F)onto the mounting strip(C)
2. Attach mounting strip(C) to junction box using outlet box screws(B).
3. Adjust chain(J) to desired length. Spread end link of chain(J).
Use a pair of pliers and a screw-driver as shown above. Wrap a soft cloth
around pliers to protect the finish.
4. Attach one end of chain(J) to fixture loop(K) and the other end to
screw collar loop(E).
6. Strip 3/4” of insulation from wire ends. Twist stripped ends together
with pliers black to smooth (power) white to ribbed (neutral). Snip ends.
Attach copper wire to ground wire and attach to green ground screw
7. Attach wire nuts(A). Tape nuts and wires together.
8. Attach screw collar loop(E) to nipple(G), tighten nut.
9. Screw loop(K) into the socket assembly(L).
10. Install light bulb(O). Use fluorescent 1-26 GU24-base bulb or less
11. Attach glass holder(P) to socket assembly(L) by aligning screws of
glass holder(P) with holes in socket assembly(L), Insert rubber washer(M)
to the screws and secure with nut(T).
CLEANING:
CLEANING:
Use only soft cloth to
dust and clean fixture. Never use
chemicals or abrasive cleaners as it may damage finish.
5. Weave electrical wires and ground wire up chain(J),
Through screw collar loop(E), through canopy(D) and into outlet box.
Product assembly must be carried out by qualified personnel only.
Product assembly must be carried out by qualified personnel only.
PRINTED IN CHINA
2 year limited warranty
2 year limited warranty
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Bulb(included) O
  • Page 1 1

Bel Air Lighting PL-50491 BK User manual

Bel Air Lighting
Brand
Bel Air Lighting
Model
PL-50491 BK
Type
User manual

Bel Air Lighting PL-50491 BK is a lighting fixture that requires assembly before use. It is designed to be installed on a ceiling and can be used in various rooms of your home. The fixture comes with a 2-year limited warranty.

The fixture uses a 1-26 GU24-base bulb which is included with the purchase. It also has a chain that can be adjusted to the desired length, allowing you to customize the height of the fixture.

To install the fixture, you will need to turn off the power to the circuit breaker or fuse panel. Then, remove the old fixture and disconnect the wiring. Next, attach the mounting strip to the junction box using outlet box screws. Adjust the chain to the desired length and attach it to the fixture loop and screw collar loop.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents