Sub-Zero BI-48SID/S Installation guide

CLASSIC REFRIGERATION

INSTALLATION GUIDE

SPECIFICATIONS, INSTALLATION, AND MORE

2 | Sub-Zero Customer Care 800.222.7820

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

CLASSIC REFRIGERATION

Contents

3 Classic Refrigeration

4 Opening Dimensions

8 Dual Installation

8 Electrical

9 Plumbing

9 Preparation

10 Anti-Tip Bracket

12 Placement

12 Water Line

13 Custom Panels

16 Alignment

17 Completion

Features and specications are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

subzero.com | 3

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. The

rating plate is located at the top frame of the unit, inside the

door. Refer to the illustration below.

If service is necessary, contact Sub-Zero Factory Certied

Service with the model and serial number. For the name

of the nearest Sub-Zero Factory Certied Service or for

questions regarding the installation, visit the Support

and Service section of our website, subzero.com, or call

Sub-Zero Customer Care at 800-222-7820.

Tools and Materials

• Screwdrivers—standard and Phillips.

• Power drill.

• Drill bits (masonry bits required for concrete installation).

• Torx drives—T-10, 15, and 20.

• Standard Allen wrench set.

• Standard socket and wrench set.

• 2' and 4' levels.

• Tubing cutter.

• 3' of

1

/4" OD copper, braided stainless steel, or PEX

tubing.

• Saddle valve.

• Material to protect home, ooring, and cabinetry during

installation.

Rating plate location

RATING

PLATE

CLASSIC REFRIGERATION

4 | Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Opening Dimensions

STANDARD INSTALLATION

3

/

4

"

(19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/

2

"

(89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit

.

83

3

/4"

(2127)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

FRONT VIEW

SIDE

VIEW

TOP VIEW

W

OPENING WIDTH

If two units are installed side by side, refer to page 6.

OPENING WIDTH

W

30" Model 29

1

/2" (749)

36" Model 35

1

/2" (902)

42" Model 41

1

/2" (1054)

48" Model 47

1

/2" (1206)

subzero.com | 5

Opening Dimensions

FLUSH INSET INSTALLATION

Dimensions assume a

3

/4" (19) panel thickness. If two units

are installed side by side, refer to page 7.

84"

(2134)

FLUSH

INSET

HEIGHT

1

/4"

(6)

26

3

/16"

(665)

FLUSH

INSET

DEPTH

2

3

/16"

(56)

NOTE:

3

1

/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit with

3

/4" (19) panel.

FRONT VIEW

SIDE

VIEW

TOP VIEW

1

/4"

(32)

W

FLUSH INSET WIDTH

FINISHED

CLEATS

5

11

/16"

(145)

FINISHED

RETURN

FILLER

FRAMED

CABINETRY

W

CLEAT

3

/4" (19)

TYPICAL

3

1

/2"

(89)

5

11

/

16

"

(145)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

1

/2"

(89)

CLEAT

3

/4" (19)

TYPICAL

SITE PREPARATION

FLUSH INSET WIDTH

W

30" Model 32" (813)

36" Model 38" (965)

42" Model 44" (1118)

48" Model 50" (1270)

6 | Sub-Zero Customer Care 800.222.7820

Opening Dimensions

DUAL STANDARD INSTALLATION

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit

.

83

3

/4"

(2127)

OPENING

HEIGHT

24" (610)

OPENING

DEPTH

FRONT VIEW

SIDE

VIEW

TOP VIEW

W

OPENING WIDTH

3

/

4

"

(19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/

2

"

(89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

A dual installation kit is required for this installation.

SITE PREPARATION

DUAL OPENING WIDTH

W

Two 30" Models 59

3

/4" (1518)

30" and 36" Models 65

3

/4" (1670)

Two 36" Models 71

3

/4" (1822)

subzero.com | 7

Opening Dimensions

DUAL FLUSH INSET INSTALLATION

84"

(2134)

FLUSH

INSET

HEIGHT

1

/4"

(6)

26

3

/16"

(665)

FLUSH

INSET

DEPTH

2

3

/16"

(56)

FRONT VIEW

SIDE

VIEW

TOP VIEW

FINISHED

CLEATS

1

/4"

(32)

W

FLUSH INSET WIDTH

NOTE:

3

1

/2" (89) finished returns and shaded areas will be visible and should be finished to match cabinetry.

Shaded line represents profile of unit with

3

/4" (19) panel.

5

11

/16"

(145)

FINISHED

RETURN

FILLER

FRAMED

CABINETRY

W

CLEAT

3

/4" (19)

TYPICAL

3

1

/2"

(89)

5

11

/

16

"

(145)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

1

/2"

(89)

CLEAT

3

/4" (19)

TYPICAL

Dimensions assume a

3

/4" (19) panel thickness. A dual instal-

lation kit is required for this installation.

SITE PREPARATION

DUAL FLUSH INSET WIDTH

W

Two 30" Models 62

1

/4" (1581)

30" and 36" Models 68

1

/4" (1734)

Two 36" Models 74

1

/4" (1886)

8 | Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Electrical Requirements

Installation must comply with all applicable electrical codes.

The electrical supply should be located within the shaded

area shown in the illustration below. A separate circuit ser-

vicing only this appliance is required. A ground fault circuit

interrupter (GFCI) is not recommended and may cause inter-

ruption of operation.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp dedicated circuit

Receptacle 3-prong grounding-type

CAUTION

The outlet must be checked by a qualied electrician

to be sure it is wired with the correct polarity. Verify the

outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter, or

remove the power cord ground prong.

75

1

/2" (1918)

FROM FLOOR

7"

(178)

E

6"

(152)

RIGHT SIDE

OF OPENING

Electrical supply location

Dual Installation

If two units are installed side by side, a dual installation kit

may be required. Installations without a custom ller strip

require a dual installation kit. If a dual installation kit is not

specied, a 2"

(51) ller strip is recommended between units.

Dual installations without a ller strip can only be accom-

plished using two units with opposite hinges. Refer to the

illustrations below.

Dual installation kits are available through an authorized

Sub-Zero dealer. For local dealer information, visit the nd a

showroom section of our website, subzero.com. For ques-

tions regarding the installation, call Sub-Zero Customer

Care at 800-222-7820.

WITHOUT FILLER STRIP

FILLER STRIP

Opposite hinges

Same side hinges

subzero.com | 9

SITE PREPARATION

Plumbing Requirements

Installation must comply with all applicable plumbing codes.

The water supply line should be located within the shaded

area shown in the illustration below. The water supply line

should be connected to the house supply with an easily

accessible shut-off valve. Do not use self-piercing valves.

The water supply line must not interfere with the installation

of the anti-tip brackets.

A reverse osmosis system can be used provided there is

constant water pressure of 35–120 psi

(2.4–8.3 bar) supplied

to the unit at all times. In this application, the water ltration

system must be bypassed by removing the lter. A copper

line is not recommended for this application.

PLUMBING REQUIREMENTS

Water Supply

1

/4" OD copper, braided

stainless steel, or PEX tubing

Pressure 35–120 psi

(2.4–8.3 bar)

Excess Line for Connection 36" (914)

Preparation

Uncrate the unit and inspect for damage. Remove the wood

base and discard the shipping bolts and brackets. Remove

and recycle packing materials. Do not discard the kickplate,

anti-tip brackets, and hardware.

Completely retract the front leveling legs to allow the unit to

be moved into position. The front and rear leveling legs can

be adjusted from the front once the unit is in position.

Remove the drain pan from the base of the unit to avoid

damage and to allow for proper placement of the appliance

dolly.

The grille assembly should be removed prior to moving the

unit. To remove, pull out on the bottom edge of the grille and

rotate upward. Loosen the back two grille mounting screws

and remove the front two grille mounting screws. Refer to

the illustrations below. With the grille held rmly, pull forward

to remove.

BACK GRILLE

SCREW

FRONT

GRILLE SCREW

Grille removal

Grille mounting screws

3" (76)

18" (457)

6" (152)

RIGHT SIDE

OF OPENING

AREA EXTENDS

1

/2" (13)

FORWARD ON FLOOR

Water supply location

10 | Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

WOOD FLOOR APPLICATION

After properly locating the anti-tip brackets in the opening,

drill pilot holes

3

/16" (5) diameter maximum in the wall studs

or wall plate. Use the #12 screws and washers to secure the

brackets. Verify the screws penetrate through the ooring

material and into the wall studs or wall plate a minimum of

3

/4" (19). Refer to the illustration below.

CONCRETE FLOOR APPLICATION

After properly locating the anti-tip brackets in the opening,

drill pilot holes

3

/16" (5) diameter maximum in the wall studs

or wall plate. Drill

3

/8" (10) diameter holes into the concrete

a minimum of 1

1

/2" (38) deep. Use the #12 screws and

washers to secure the brackets to the wall, and use the

3

/8"

wedge anchors to secure the brackets to the oor. Verify

the screws penetrate the wall studs or wall plate a minimum

of

3

/4" (19). Refer to the illustration below.

4" (102)

MIN

24"

(610)

SUBFLOORING

WOOD FLOOR

WALL PLATE

FINISHED

FLOORING

4" (102)

MIN

24"

(610)

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

1

/2"(38)

min

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

1

/2"(38)

MIN

Wood oor

Concrete oor

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

brackets must be installed.

The two anti-tip brackets must be installed exactly 24"

(610)

from the front of the opening to the back of the

brackets and a minimum of 4"

(102) from the sides of the

opening. This depth will increase to 26

3

/16" (665) for a ush

inset installation based on

3

/4" (19) thick panels. Failure to

properly position the anti-tip brackets will prevent proper

engagement.

Use all anti-tip bracket hardware as instructed for wood or

concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the

#8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to

fasten the anti-tip brackets to the back wall.

ANTI-TIP HARDWARE

2 Anti-tip brackets

12 #12 x 2

1

/2" pan head screws

4

3

/8"–16 x 3

3

/4" wedge anchors

12 #12 at washers

4 #8–18 x 1

1

/4" truss head screws

4 Nylon Zip-it

®

wall anchors

subzero.com | 11

SITE PREPARATION

Anti-Tip Bracket

CONCRETE WEDGE ANCHOR INSTALLATION

1 Drill a

3

/8" (10) diameter hole any depth exceeding the

minimum embedment. Clean the hole or drill additional

depth to accommodate the drill nes.

2 Assemble the washer and nut ush with the end of

anchor to protect threads. Drive the anchor through the

material to be fastened until the washer is ush with the

surface material.

3 Expand the anchor by tightening the nut 3–5 turns past

hand-tight position or to 25 foot-pounds of torque.

WARNING

Verify there are no electrical wires or plumbing in the

area which the screws could penetrate.

CAUTION

Always wear safety glasses and use other necessary

protective devices or apparel when installing or working

with anchors.

Anchors are not recommended for use in lightweight

masonry material such as block or brick, or for use in

new concrete which has not had sufcient time to cure.

The use of core drills is not recommended to drill holes

for the anchors.

12 | Sub-Zero Customer Care 800.222.7820

INSTALLATION

Water Line

Approximately 3' (.9 m) of

1

/4" plastic tubing is connected to

the unit with a preassembled

1

/4" compression connection

under the unit. The water line tting connection kit, provided

with the unit, contains a

1

/4" compression union tting for

connection to the household water line.

Purge the water line prior to nal connection to the unit. This

will remove any debris that may be present in the tubing

from installing the new water line.

Place the sleeve and nut on the water line and fasten to the

connection at the end of the tubing. Do not over tighten.

Check all water line ttings for leaks. Verify the drain pan

can be installed and removed without interference with the

water line.

IMPORTANT NOTE: If a reverse osmosis system is used, it

is recommended the water ltration system be bypassed by

removing the lter.

IMPORTANT NOTE: Water lines cannot be exposed to

freezing temperatures.

Placement

CAUTION

Before moving the unit into position, secure door(s)

closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

Plug the power cord into the grounded outlet and roll the

unit into position. Verify the anti-tip brackets are properly

engaged.

IMPORTANT NOTE: If used, the side panels must be

installed before the unit is placed in its nal position. Refer

to page 15.

subzero.com | 13

EXTERNAL DISPENSER

For external dispenser models, the dispenser bezel must be

removed before the custom panels can be installed.

The bezel will accommodate a

1

/4" (6) thick panel for framed

applications and a

3

/4" (19) thick panel for overlay and

ush inset applications. Panels thicker than

3

/4" (19) must

be routed in the dispenser area to 1

1

/8" (29) (including the

backer and spacer panels).

To Remove the Bezel:

1 Lift, rotate, and remove the tray.

2 Lift and remove the grille.

3 Remove the screw from the center of the chute and

remove the chute.

4 Rotate the control panel downward and disconnect the

wire harness.

5 Remove the screws from each corner of the bezel and

pull the bezel forward.

PANEL INSTALLATION

Custom Panels

For overlay and ush inset applications, custom door and

grille panels must be installed. The panel size is critical for

a proper t. To verify panel requirements and dimensions,

refer to the Sub-Zero Design Guide at subzero.com/specs.

IMPORTANT NOTE: Flush inset applications require a

minimum

1

/2" (13) reveal on all sides.

Finish all sides of the custom panels. They may be visible

when the door is open or through the window of glass door

models.

GRILLE

TRAY

CHUTE

Tray and grille removal

Dispenser bezel removal

14 | Sub-Zero Customer Care 800.222.7820

PANEL INSTALLATION

Custom Panels

DOOR PANELS

To install custom door panels, remove the handle side trim

molding. Insert a screwdriver tip into the top corner slot

on the handle side and pop out the trim. For the drawer,

insert a screwdriver tip into the slot on either side of the trim

running along the top of the drawer and pop out the trim.

Remove the screws and frame. Refer to the illustrations

below.

The door has a

1

/4" (6) frame for the custom panel to slide

into. If the panel is thicker than

1

/4" (6), rout an edge around

the panel or mount the panel on a sheet of

1

/4" (6) thick

material, then insert into the frame.

A .10"

(3) space is required between the backer panel and

the custom panel to allow the panel to slide into the door

frame. Refer to the illustrations below for critical dimensions.

Install handle hardware before inserting the panel. Large

D-style handles are recommended rather than knobs. Screw

heads must be countersunk into the panel.

Slide the panel into the frame.

To reinstall the door trim molding, insert the top of the trim

into grooves at the top of the door and work downward,

snapping the trim into clips on the door frame. For the

drawer, start at one end and move towards the opposite

end, snapping the trim into the clips.

1

/8" (3) (OVERLAY)

CUSTOM PANEL

SPACER PANEL

BACKER PANEL

TRIM

5

/16" (8) min

1

/4" (6)

.10" (3)

CUSTOM

PANEL

SPACER

PANEL

BACKER

PANEL

3

/4"

(19)

typical

Panel assembly cross section

(overlay)

Panel assembly rear view

Door side trim

Drawer top trim

subzero.com | 15

Custom Panels

GRILLE PANEL

Remove the bottom grille frame by extracting the two lower

corner screws from each side of the grille assembly. Refer to

the illustration below.

With the bottom section removed, slide the custom grille

panel into the frame. If the panel is thinner than

1

/4" (6), a

ller material will need to be installed to achieve a proper

t. Once the panel is installed, reattach the bottom grille

frame by sliding the corner brackets back into position, then

reinstall the four corner screws.

PANEL INSTALLATION

SIDE PANEL

When installing a custom side panel, an accessory kit is

required and is available through an authorized Sub-Zero

dealer. For local dealer information, visit the nd a show-

room section of our website, subzero.com. Stainless steel

and white enamel side panels are also available from an

authorized Sub-Zero dealer.

IMPORTANT NOTE: The use of side panels may change the

width of the opening.

A custom side panel must be a minimum of 24"

(610) deep

and

1

/2" (13) thick. Routing will be necessary for the side

panel to t ush against the side of the unit. Refer to the

illustrations below.

IMPORTANT NOTE: The height of the side panel will vary

with the height of the grille. Verify the nished height before

modifying the panels.

IMPORTANT NOTE: For over-and-under and French door

models, additional routing will be necessary to accommo-

date the lower hinge plate of the refrigerator.

84"

(2134)

24"

(610)

ROUT TO

3

/16" (5)

(OVER-AND-UNDER

MODELS)

OPTIONAL

TOE KICK

CUT-OUT

4" (102)

20

1

/2"

(521)

5

3

/4"

(146)

1

7

/8"(48)

1" (25)

4

1

/4" (108)

ROUT TO

1

/8" (3)

FRONT

OF SIDE

PANEL

2

5

/8"

(67)

MAIN

FRAME

SIDE PANEL

ROUTING

1" (25)

1

7

/8" (48)

1

/8" (3)

1

/2" (13)

Side panel dimensions

Routing detail

BOTTOM

GRILLE

FRAME

Grille frame assembly

16 | Sub-Zero Customer Care 800.222.7820

INSTALLATION

DOOR ADJUSTMENT

The doors of side-by-side and over-and-under models can

be adjusted in and out, and side to side tilt. The doors of

side-by-side models can also be adjusted up and down.

To make adjustments, slightly loosening the two upper hinge

bolts on the upper hinge plate using a

1

/2" wrench. Refer to

the illustration below.

In-and-Out Adjustment: For a left-hinge door, using a

5

/32" allen wrench, turn the adjustment bolt clockwise to

bring the handle side of the door inward, and counterclock-

wise to move the handle side outward. Reverse directions

for a right-hinge door.

Side-to-Side Tilt Adjustment: For a left-hinge door, using a

3

/8" wrench, turn the adjustment bolt clockwise to raise the

handle side of the door, and counterclockwise to lower the

handle side. Reverse directions for a right-hinge door.

Up-and-Down Adjustment: For a left-hinge door, using a

1

/4" allen wrench, turn the adjustment bolt clockwise to raise

the door and counterclockwise to lower. Refer to the illustra-

tion below. Reverse directions for a right-hinge door.

Alignment

LEVELING

Once the unit is in position, turn the front leveling legs

clockwise to adjust the height. The rear height adjustment

can be made from the front of the roller base. Using a

3

/8"

socket, turn the

3

/8" hex bolt clockwise to raise the unit or

counterclockwise to lower. Use the lowest torque setting

when using a power drill. Do not turn the rear leveling legs

by hand. Refer to the illustration below.

When the unit is properly leveled, door and drawer adjust-

ments are less likely to be necessary.

IMPORTANT NOTE: Level the unit to the oor, not the sur-

rounding cabinetry. This could affect the operation of the

unit, such as door closing.

WARNING

To reduce the possibility of the unit tipping forward, the

front leveling legs must be in contact with the oor.

FRONT

LEVELING LEG

REAR

ADJUSTMENT

Rear roller base adjustment

UPPER

HINGE BOLTS

SIDE-TO-SIDE

TILT ADJUSTMENT

IN-AND-OUT

ADJUSTMENT

Door adjustment bolts

Up-and-down door adjustment

subzero.com | 17

INSTALLATION

ANCHORING

After the unit has been leveled and door adjustment com-

pleted, anchor the unit to the opening to ensure a proper t

and secure installation.

To anchor the top of the unit, open the grille and install the

screws provided through the grille frame into cabinetry.

There are several hole locations. Refer to the illustration

below. Check for proper door clearance by opening the

door.

To anchor the bottom of the unit, drive a screw through the

side hole inside each roller base assembly. The screw will

need to go in at an angle to attach properly. Refer to the

illustration below. Additional material may be needed behind

the cleat to ensure sufcient anchoring.

CAUTION

If the screws provided are not suitable for the installa-

tion, use adequate screws.

ANCHORING

SCREWS

ANCHORING

SCREW

Top anchoring

Bottom anchoring

Completion

GRILLE INSTALLATION

Install the grille assembly and check for proper t. The grille

is designed to rest on the upper door hinge(s) to minimize

the reveal between the top of the door and bottom of the

grille. To eliminate interference, the grille height can be

adjusted. Loosen the four grille adjustment screws (two on

each side) and adjust the grille height as needed. Refer to

the illustration below.

BACK GRILLE

SCREW

FRONT

GRILLE SCREW

GRILLE

ADJUSTMENT

SCREW

Grille height adjustment

18 | Sub-Zero Customer Care 800.222.7820

Completion

Reinstall the drain pan and verify it is in the proper position.

Install the kickplate using the screws to attach it to the

brackets on the inside of each roller base. Refer to the illus-

tration below. The kickplate must be removable for service.

The oor cannot interfere with removal. Refer to the label

mounted on the kickplate support for height clearance.

Turn power on by touching POWER on the control panel.

Install the light diffuser by aligning the slots of the light

diffuser onto the bracket pegs and pulling forward so the

tabs on the slots engage the bracket pegs. Refer to the

illustration below.

INSTALLATION

PEG

SLOT

Kickplate installation

Light diffuser installation

WATER FILTER BYPASS

If the water ltration system will not be used, it can be

placed in water lter bypass mode by removing the water

lter. Refer to the illustration below. Follow these steps to

remove the water lter:

1 Pull out on the bottom edge of the grille assembly and

tilt the grille frame upward.

2 To remove the cartridge, rotate the cartridge counter-

clockwise one-quarter turn and pull out. Refer to the

illustration below.

WATER

FILTER

WATER FILTER

Location of water lter

Water lter removal

subzero.com | 19

WARNING

Follow all city and state laws when storing, recycling,

or discarding unused refrigerators and freezers.

Completion

90° DOOR STOP

The doors of all models open to 110°. A 90° door stop is

provided with the unit (located behind the grille). Additional

90° door stop kits are available through an authorized

Sub-Zero dealer.

INSTALLATION

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.

Page is loading ...