Grizzly T27952 Owner's manual

Brand: Grizzly

Model: T27952

Type: Owner's manual

Grizzly T27952, a sturdy and versatile storage solution, offers ample space for organizing tools and equipment. Its single drawer, with a weight capacity of 85 lbs, can accommodate heavier items, while each shelf can hold up to 325 lbs, providing ample storage for a variety of tools. The cabinet's total weight capacity is 750 lbs, ensuring it can handle even the most demanding storage needs.

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T27952

1-DRAWER, 2-DOOR

CABINET

INSTRUCTIONS

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 10.16) #JH18543 PRINTED IN CHINA

V1.07.17

Introduction

The Model T27952 1-Drawer, 2-Door Cabinet

requires some assembly. Follow the instructions

below for assembly, operation, and maintenance.

Figure 1. Model T27952.

• To reduce risk of crushing injuries from

tool cabinet tipping over on you:

— Do not stand on cabinet or in drawer.

— Only move or transport cabinet with

drawer and doors closed and locked.

— Push cabinet only (do not pull it) when

moving.

• Do not exceed weight capacities:

— Max drawer weight limit is 85 lbs.

— Max individual shelf weight limit

is 325 lbs.

— Max total tool cabinet weight limit

(including contents) is 750 lbs.

• To prevent accidental tipping, ensure

adjustable feet are properly adjusted and

cabinet body is level.

• Do not allow children to have unsupervised

access to cabinet.

Maintenance

• Use a soft, clean cloth and soapy water to

remove grease, dirt, or oil.

• Lubricate drawer slides as needed with dry

lubricant.

• Use graphite to lubricate lock annually.

Inventory Qty

• Tool Cabinet with Drawers ........................... 1

• Cabinet Feet ................................................ 4

• Keys ............................................................. 2

Assembly

The Model T27952 comes with four adjustable

feet for leveling the cabinet.

To install feet:

1. With help from another person, lay cabinet

upside down on floor (see Figure 2).

2. Install one adjustable foot in each corner (see

Figure 2).

3. Level cabinet body by rotating the cabinet

feet up or down as needed.

Figure 2. Location of adjustable feet.

Adjustable Feet

-2-

T27952 Tool Cabinet (Mfd. 10/16)

Removing & Installing Drawer

To remove drawer:

1. Fully extend drawer and remove contents.

2. Push left locking tab on drawer runner down

and hold, then pull right locking tab on drawer

runner up and hold (see Figure 5).

3. Remove drawer from drawer slide.

The drawer can be removed and re-installed if

necessary.

Figure 5. Location of drawer locking tab.

Drawer

Runner

Adjusting Doors

To adjust doors:

1. Close door and visually confirm gap spacing

around door edge is

⁄8" all the way around

(see Figure 3).

— If door spacing is equal, no adjustments

are needed.

— If door spacing is not equal, proceed to

Step 2.

Each 90° soft-close door hinge is riveted in place.

However, the doors may be adjusted inward or

outward, and left or right, as needed.

2. Adjust door hinges using screws shown in

Figure 4.

Note: Only small adjustments, such as

⁄8

⁄4 turn at a time, are required to move

door position. Check spacing after each

adjustment.

Figure 3. Checking door gap spacing.

⁄8" Gap

Installing Shelf Brackets

Each shelf comes with four shelf support designed

to fit into the channel bracket inside the cabinet

(see Figure 6), making the position of each shelff

adjustable. (Shelf support must be mounted even-

ly to function properly.)

Shelf

Support

Channel

Bracket

Figure 6. Shelf support and channel bracket.

4. To re-install drawer, extend drawer slides out

all the way, insert drawer runners into slides,

and close drawer entirely. Locking tabs will

click in place as drawer is closed, which will

fully attach drawer to slides.

Figure 4. Hinge adjustments.

In/Out

Adjustment

Right/Left

Adjustment

Locking Tab

T27952 Tool Cabinet (Mfd. 10/16)

-3-

Parts Breakdown & List

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT27952001 CABINET BODY 12 PT27952012 DOOR (LEFT)

2 PT27952002 ADJUSTABLE FEET M12-1.75 X 30 13 PT27952013 DOOR HANDLE

3 PT27952003 CABLE GROMMET 14 PT27952014 DRAWER LINER

4 PT27952004 SHELF SUPPORT 15 PT27952015 FLAT HD SCR M4-.7 X 8

5 PT27952005 SHELF 16 PT27952016 LOCK W/2 KEYS

6 PT27952006 DRAWER SLIDE 20" 17 PT27952017 TOUCH-UP PAINT, GLOSSY BLACK

7 PT27952007 DRAWER HANDLE CAP 18 PT27952018 TOUCH-UP PAINT, RED

8 PT27952008 DRAWER HANDLE 19 PT27952019 WARNING LABEL

9 PT27952009 DRAWER 20 PT27952020 QR CODE LABEL

10 PT27952010 HINGE, 90-DEG SOFT-CLOSE 21 PT27952021 GRIZZLY.COM LABEL, GOLD

11 PT27952011 DOOR (RIGHT)

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

Grizzly Cabinet Series

T27947 T27952 T27951T27948

T27953

T27950

T27949

The T27952 Single-Drawer, Two-Door Cabinet is part of our heavy-duty 10-piece storage set. These modu-

lar cabinets will enhance storage and workspace in the shop or garage, and they can be mixed and matched

to create a variety of storage solutions.

Grizzly T27952 Owner's manual

Grizzly T27952 Owner's manual

Grizzly T27952 Owner's manual

Related papers

Other documents