OWNER’S MANUAL
OM274432A 2016−01
Continuum)
Axcess)
Centerpoint 9 Compatibility
ORIGINAL INSTRUCTIONS − PRINTED IN USA © 2016 Miller Electric Mfg. Co.
Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.
Read the safety information at the beginning of the manual and in each section.
1-1. Continuum Compatibility
. To use Centerpoint 9 with Continu-
um products the system software
revision must be 272930D or
higher.
Checking Software Revision
1 System Soft Key
From the home screen on the user in-
terface, press the System softkey.
2 Scroll Knob and Select/Save
Button
3 System Software Revision
At the System Menu, rotate the scroll
knob until the System Software Revi-
sion option is active. Press the scroll
knob to display System Software
Revision.
If Software Revision Is 272930C Or
Lower
Download the latest software at −
http://www.millerwelds.com/products/
advanced/continuumsoftware.php
If Software Revision Is 271403G Or
Lower
Order and install upgrade kit 273422.
If you need assistance, call the ISG
Service Group at 920−954−3809.
Home
Home > System
System Menu
Factory Reset
3
2
USB Functions
System Software Revision
Network Settings
Machine Serial Number
Back
Ref 266 061-A
Logs StatusSetup System
Home
Program # 1
Accupulse
.035 Steel E70
Ar 90 CO2 10
1
WiFi Ethernet
OM274432 Page 2
. To use Centerpoint 9 with Axcess
E products the PCM software revi-
sion must be 713N or higher.
If PCM Software Revision Is Lower
Than 713N Or A Different Number
Download the latest software at −
http://www.millerwelds.com/products/
advanced/software.php
If you need assistance, call the ISG
Service Group at 920−954−3809.
After entering the user interface
menu, the initial display will vary by
the first item that appears.
SYS
RST
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
REV
SW
Rotate Adjust knob until Software
Revision (SW REV) appears on
the display.
1-2. Axcess E Compatibility
AXCS
450
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
To enter the user interface menu, mo-
mentarily press the Program push but-
ton and lower display push button at
the same time.
Upper display push button LED
flashes to indicate this menu item
is available for selection. Press
the upper display push button.
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
SW
REV
Rotate Adjust knob to scroll
through the software revision until
PCM is displayed.
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
PCM
123A
LED
PCM
123A
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
The Set Up push button LED flashes indicating
that pressing this button will exit the user
interface menu. Press the Set Up push button.
PCM
123A
Trigger Control
Program
Process
Wire Type
Gas Type
Process Set up
Volts Time Arc Adjust
WFS Amps Arc Ctl
Sequence
Trigger Hold
Adjust Feeder Set Up
To exit the user interface menu, momentarily
press the Program push button and lower
display push button at the same time.
/
