TTi Part Number:
EC
EC
Date
* See back page for date code and revisions.
T
C
Item ID
01608500401Q
ECN-CM015292
Nov 10, 2017
CM00123290
IMPORTANT SAFETY INSTRUCTIONS
WARNING
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SAVE THESE INSTRUCTIONS
SYMBOLOGY
SPECIFICATIONS
Cat. No. ....................................................................................................................HL-LED
Volts............................................................................................................................4.5 DC
Ingress Protection...........................................................................................................IP52
Battery Type....................................................................................................LR03 / AAA x3
Recommended Ambient
Operating Temperature.............................................................0°C to 52°C (0°F to 125°F)
ASSEMBLY
OPERATION
WARNING
HEADLAMP
Changing Batteries
Only use alkaline batteries. Do not use zinc-carbon batteries. If the light will not be
used for a long time, remove the batteries as a protection against corrosion.
To change the batteries:
Open the battery compartment on the back of the light.
Insert three AAA batteries according to the polarity marked in the compartment.
Close the battery compartment.
Cat. no. HL-LED
To reduce the risk of injury, do not look directly into the light when
the light is on.
Clip the light onto the strap and use the buckle to adjust the strap to the required size. Use
the included clips to attach to a hard hat. Rotate the light up or down as needed.
READ AND UNDERSTAND ALL INSTRUCTIONS. When using
electric appliances, basic precautions should always be followed,
including the following:
Before using the light, read this operator's manual and all labels on the light.
Read and understand all the instructions before using the appliance.
To reduce the risk of injury, close supervision is necessary when an appliance is
used near children.
Store idle light out of reach of children. Warm lights can become hazardous in the
hands of children.
Know your light. Read this manual carefully to learn your light's applications and
limitations as well as potential hazards associated with this type of light.
This tool is designed to be powered by 3-AAA batteries properly inserted into the
tool. Do not attempt to use with any other voltage or power supply.
Do not leave batteries within the reach of children.
Do not mix new and used batteries.
Do not mix brands (or types within brands) of batteries.
Do not mix rechargeable and non-rechargeable batteries.
Install batteries according to polarity (+ / -) diagrams.
Properly dispose of used batteries immediately.
Do not incinerate or dismantle batteries.
Under abusive conditions, liquid may be ejected from the battery, avoid contact.
If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irritation
or burns.
Do not dispose of tool or batteries together with household waste material!
Appliance and batteries that have reached the end of their life must be collected
separately and returned to an environmentally compatible recycling facility.
Maintain labels and nameplates. These carry important information. If unreadable or
missing, contact a MILWAUKEE
®
service facility for a replacement.
1.
2.
3.
Press the power button to cycle through High, Medium, Low, and Off. From any setting,
press and hold the power button to turn the light off.
Volts
Direct Current
Read Operator's
Manual
Regulatory Compliance mark (RCM).
This product meets applicable
regulatory requirements.
Class III protection
Do not stare at light source.
ADDITIONAL BATTERY SAFETY RULES
WARNING
To reduce the risk of fire, personal injury, and product damage due to a short
circuit, never immerse your tool, battery pack or charger in fluid or allow a
fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial
chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
MAINTENANCE
WARNING
Contact a MILWAUKEE
®
service facility for ALL repairs.
WARNING
ACCESSORIES
WARNING
To reduce the risk of injury, always remove the battery before
performing any maintenance. Never disassemble the tool.
WARNING
The light source of this luminaire is not replaceable; when the light
source reaches its end of life the whole luminaire shall be replaced.
Maintain light
Keep your light in good repair by adopting a regular maintenance program. If the light
does not work properly, return the light to a MILWAUKEE
®
service facility for repairs.
To reduce the risk of personal injury and damage, never
immerse your tool in liquid or allow a liquid to flow inside.
Cleaning
Keep tool handles clean, dry and free of oil or grease. Use only mild soap and a damp
cloth to clean the tool since certain cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include gasoline, turpentine, lacquer thinner,
paint thinner, chlorinated cleaning solvents, ammonia and household detergents
containing ammonia. Never use flammable or combustible solvents around tools.
Use only recommended accessories. Others may be hazardous.
For a complete listing of accessories, go online to www.milwaukeetools.com.au /
www.milwaukeetools.co.nz or contact a distributor.
WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
Please refer to Australian and New Zealand warranty supplied with tool. This warranty
applies only to product sold in Australia and New Zealand.
MILWAUKEE
®
prides itself in producing a premium quality product that is Nothing But
Heavy Duty
®
. Your satisfaction with our products is very important to us! If you
encounter any problems with the operation of this tool, please contact your authorised
MILWAUKEE
®
dealer.
For a list of MILWAUKEE
®
dealers, guarantee or service agents please contact
MILWAUKEE
®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 279 624)
or visit www.milwaukeetools.com.au / www.milwaukeetools.co.nz.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
21 Kelletts Road, Rowville, VIC 3178
Melbourne, Australia
Milwaukee Tool (New Zealand)
2 Landing Drive, Mangere
Auckland, 2022, New Zealand
Designed by Milwaukee Electric Tool Corp.
Professionally Made in China for Milwaukee Tool (Australia) / Milwaukee Tool (New Zealand)
Printed in China
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Milwaukee M18 ONESLDP User manual
-
Milwaukee M18 PAL User manual
-
Milwaukee M18 User manual
-
Milwaukee M18 TAL User manual
-
-
-
-
Milwaukee M18 UBL User manual
-
Milwaukee M18 HCC75R User manual
-