Page 1/2
Fig.1
INSTALLATION INSTRUCTIONS FOR
N7259-613
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
AVERTISSEMENT!COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DO DISJONCTEU
ASSEMBLINGTHEFIXTURE(Fig.1)
1 Shutoffpoweratthefuseboxorcircuitbreakerbox.If
necessary,removetheexistingfixtureanditsmounting
hardware.
2 Carefullyremovethenewfixturefromthecartonandcheck
thatallpartsareincludedasshownintheillustration.
3 UsingAllenwrench(O)providedunscrewsthescrew(N)to
takeouttheloop(J)andmetalplate(P),thengentlypullthe
excessiveblack/whitewiresintothesplicebox(Q).Fixedthe
metalpart(V)andpart(W)withscrews(u)(size:#5‐320.5"L)
asshownin
Fig.3.
4 Fixedthesidearm(S)ontothesplicebox(Q) withscrews(R)
(size:#5‐320.25"L)asshowninFig.3
5 Secured the side arm (S) to fixture body (T ) with screws (R)
(size:#5‐320.25"L)asshowninFig.3.
6 Recover the metal plate (P) and secure the loop(J), then
secured withAllenwrench(O)asshowninFig.3.
7 Thisfixtureincludesthree12",andone6"rods.Determinethe
desiredhangingheightandthreadrods(K)(Part#W35‐1‐613),
(L)(Part#W35‐H‐613)toloop(J).Feedthefixturewireand
saf etycablecarefullythrougheachrod.Pleaseremovethe
nippleifinstallingwithone6"rodonly.
8 Threadtheloop(J)torodunitsnug.
9 Connecttheloops(J)usingquicklink(I).Thequicklink(I)must
becompletelyclosedwheninstalled.
10 Installa1/4 " IPSpipe(A)(notprovided)withoneendsecurely
mountedtoabeamofastructuralmember.Theotherend
shouldprotrudethroughthecenteroftheoutletboxas
shown.
11 Securethehexnut(B)ontothepipe(A)andthensecurethe
hickey(C)tightly.
12 Threadhexnut(D)ontothenipple(E),thenthreadthenipple
(E)intothehickey(C);andsecurewithhexnut(D)onthe
otherendofnipple(E).Threadloop(H)ontonipple(E)tightly.
13 Slipthelockcollar(G)andcanopy(F)overtherod.
14 Openquicklink(I)andconnectittoloop(H/J).Thenthread
thequicklinkclosed.
15 Feedthefixtureswiresandsafetycablethroughtheceiling
loop(H)andnipple(E)andallowthemtoexitthroughtheside
ofhickey(C).Runsafetycablethroughthehickey(C)onecir cle
andsecuresafetycablewithsetscrewassemblyandsetscrew.
CONNECTINGTHEWIRES(Fig.2)
16 ConnecttheelectricalwiresasshowninFig.2,makingsure
thatallwireconnectorsaresecured.Ifyouroutlethasa
groundwire(greenorbarecopper),connectthefixture's
groundwiretoit.Afterthewiresareconnected,tuckthem
neatlyintotheoutletbox.
17.Raisecanopy(F)onto
theceilingloop(E)tofixwithlockcollar
(G)
WARNING: This luminaire must be mounted or supported
independently of an outlet box.