World Tech Toys STRIKER SPY DRONE Quick start guide

Brand: World Tech Toys

Model: STRIKER SPY DRONE

Type: Quick start guide

World Tech Toys STRIKER SPY DRONE is an advanced flying device with camera capabilities, allowing you to capture stunning aerial footage and images. With its easy-to-use remote control, you can effortlessly navigate the drone, adjusting its elevation, rotation, and direction of movement. The drone's compact size and lightweight design make it highly portable, perfect for taking on adventures or capturing unique perspectives during your travels. Additionally, the included micro-SD card provides ample storage space for your captured media, ensuring you never miss a moment.

QUICK START GUIDE

What’s included:

• Drone • Rechargeable Battery • Charging Cable • Micro SD Card

• Micro SD USB Adapter • Spare Parts Kit • Remote Control

BEFORE YOU START:

1. Find the Micro-SD card. It is located in the small zip-lock pouch with your USB adapter.

2. Slide the Micro-SD card into the back of the camera on the underside of your drone. Push until you hear a click.

The card should slide in easily. If you find it is not clicking into place, do not force the card. Remove it, and turn the

card over and try again. (To remove the card, push in until you hear a click, then the card will be easily removable)

3. Charge the drone fully by connecting the cable on the battery with the included USB cable. Plug into the USB port

of a computer or a USB compatible charging block and allow to charge for at least 90 minutes. During charging, the

USB connector will illuminate. When the battery is fully charged, the light on the USB connector will turn off.

4. Put 4 AA batteries into the Remote Control according to the diagram inside the battery compartment.

TURNING ON DRONE AND PAIRING WITH REMOTE CONTROL:

1. Unplug the battery from the charging cable.

2. Insert the battery into the compartment on the underside of the drone with the battery cable sticking out. (Note:

the camera does not need to be removed.)

3. Insert the white battery connector into the slot marked power. Then close the battery compartment.

4. Turn on the power switch on the back of the drone, place the drone on a flat level surface.

5. Turn on the Remote Control using the switch at the center of the remote. The lights on the drone will be flashing.

6. Start with the left stick on the remote control all the way down. Then push the left stick on the remote all the way

up, then all the way back down again. The lights on the drone should stop flashing and remain illuminated. This

means the drone is paired. (If this does not occur, turn off the remote control, and repeat steps 3-5.

7. Once paired, the drone is ready to fly. Keep the left stick all the way down to prevent the rotors from turning until

you are ready to fly. It is STRONGLY recommended that you use the drone outdoors during initial flights.

REMOTE CONTROL OVERVIE W:

1. Your remote control has an LCD screen on it that will give you basic information including the thrust % you are

using when flying your drone, battery life, and connection strength between the remote control and the drone. For

additional information regarding the LCD screen, please consult the user’s manual.

2. The left stick controls ELEVATION and ROTATION. Pushing the stick up will increase elevation and lowering the

stick will reduce elevation. Pushing the stick right and left will rotate the drone clockwise and counterclockwise.

3. The right stick controls direction of movement. Pushing the stick up will make the drone fly forward. Pushing down

will make the drone fly backward. Pushing left and right will make the drone fly left and right.

IMPORTANT NOTE: Once rotated, remember that the drone will still operate according to the direction it is pointing.

If the drone is facing you, for example, pushing forward will actually cause the drone to move towards you. Pushing

right will cause the drone to move to your left. Always keep track of which direction your drone is facing. The red

propellers are at the front of the drone, while the black propellers are at the back of the drone. The LED light

colors also indicate front and back.

4. Your remote control has little triangle-shaped buttons near the two sticks. These buttons on the remote “trim” the

flight. These buttons allow you to correct drifting. For example, if the drone drifts to the right a bit too much, you can

correct that with the use of the correct trim button. Please consult the user’s manual included with the drone for full

explanation of the trim buttons.

5. There are 4 buttons on the top of the remote. They are labeled according to their purpose. From right to left they

will perform the following functions: take a still photograph, start and stop video recording, the next button is not

utilized on this model, the last button on this row toggles Easy Mode.

6. Above those 4 buttons are 2 shoulder buttons. The shoulder button on the right engages 360º stunt mode. The

shoulder button on the left adjusts the speed of flight. It has three modes delineated by the number of beeps it makes

when pressed. A single beep indicates the lowest speed, two beeps indicates medium speed, and three beeps

indicates the highest speed. Low speed flying is better for tight spaces, while high speed flying is better for flight at

higher elevations and open areas, or in stronger breezes.

FLYING THE DRONE:

1. Gently push up on the left stick to gain altitude.

2. Use the right stick to move the drone forward, backward, left and right.

3. If you want to rotate the drone so that you can point the camera in a specific direction, do so by pushing the left

stick to the left or right. If you do this, keep in mind where the front of the drone is pointing because that will determine

how your controls operate.

4. If the lights start flashing slowly, that means the battery is running low.

5. It is strongly recommended that you do not fly at high elevations in strong winds, densely populated or wooded areas.

1. Before attempting to record video, ensure that any plastic covering over the lens of the camera has been removed

and discarded.

2. Once your drone is turned on and paired, and the micro-SD card is correctly inserted into the slot behind the

camera, you will see a blue light illuminate on the bottom of the camera. When you click the video-recording button,

a purple light will turn on next to the blue light. This indicates that the camera is recording. Pushing the button again

will stop recording and the purple light will turn off. A camera icon will also be displayed on the LCD screen while

recording is taking place.

3. Still photos can be taken by pressing the photo button on the top right of the remote control. The purple light under

the camera will come on briefly, then turn off again.

RECORDING VIDEO AND TAKING STILL PHOTOS:

TRANSFERRING PHOTOS AND VIDEOS TO A COMPUTER:

1. Remove the micro-SD card from the drone as explained above.

2. Insert the micro-SD card into the USB adapter that is provided.

3. Insert the USB adapter, with micro-SD inside, into the USB port of a Windows PC or Apple computer.

4. The USB adapter should appear as a folder that can be opened. Open the folder and find the video files. Drag the

files to the desktop, or other folder of your choosing. These files can now be viewed, edited and shared. Enjoy!

ITEM NO. 34937

World Tech Toys STRIKER SPY DRONE Quick start guide

Brand: World Tech Toys

Model: STRIKER SPY DRONE

Type: Quick start guide

Download PDF

report

World Tech Toys STRIKER SPY DRONE Quick start guide

World Tech Toys STRIKER SPY DRONE Quick start guide

Related papers

Other documents