2. EMS
  3. Taktis
Taktis

EMS Taktis Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the EMS Taktis Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
MK254 FireCell Taktis® Quick Start Guide Issue 3
www.emsgroup.co.uk
QUICK START GUIDE
Taktis® introduction
The Taktis range of re detection control panels are compatible with the EMS FireCell
system and EMS Fusion Radio Loop Module (RLM). All installation guidelines are the
same as when tting an EMS Syncro AS panel, although panel operation will vary.
Programmed or unprogrammed system?
This guide covers the installation of both programmed and unprogrammed systems.
More detailed manuals have been supplied in the FireCell Instruction Pack within the
control panel packaging.
Programming can be achieved either manually or via computer programs.
Manual device programming on the Taktis panel
DO NOT press the device logon buttons if the system is
supplied pre-programmed.
Doing this will unprogramme the device from the system.
PRESS HERE TO
LOG ON
Program the Control Panel; ensuring Loop number and addresses programmed at the
Radio Hub correspond to that programmed at the Control Panel.
With the write switch enabled and the control key switch in the enabled position;
Activate
Controls
Enter
PIN
Submit
Engineer
Options
Conguration
Edit Conguration Panel Modules
Add Devices
Select
device type
Select device
address
Submit
Add Wireless
Device
Select Loop
Module Number
Select Loop
Number
©2018 EMS Ltd. All rights reserved Page 2 of 6 MK254 Iss 3 18/09/2018 AJM
FireCell on Taktis - Radio Hub location recap
The Radio Hub is powered from the Control Panel’s loop connection.
For optimum wireless performance, the following must be observed:
Ensure the Control Panel and Radio Hub are installed as per the site survey.
Ensure the Radio Hub is not installed within 2m of other wireless or electrical
equipment (not including the Control Panel).
Ensure the Radio Hub is not installed within 0.6m of metal work.
2m AWAY
FROM OTHER
ELECTRICAL
EQUIPMENT
WITHIN 10m
600mm AWAY FROM METAL *
*
300mm is an acceptable
distance where 600mm is not
achievable
POWER
FAU LT
NEVER SITE THE HUB NEAR METAL WORK
OR ELECTRICAL EQUIPMENT
POWER
FAU LT
NEVER SITE THE HUB BELOW OR TO THE SIDE OF THE PANEL
POWER
FAU LT
POWER
FAU LT
POWER
FAU LT
HUB CORRECTLY SITED ABOVE THE PANEL
POWER
FAU LT
©2018 EMS Ltd. All rights reserved Page 3 of 6 MK254 Iss 3 18/09/2018 AJM
LOOP 1
IN
OUT
FireCell Radio Hub to Taktis - wiring connections
The Radio Hub has up to four separate sets of loop connections: LOOP IN -, LOOP IN +,
LOOP OUT - and LOOP OUT + for each available loop. The cable must be passed
through the entry points provided. Connections are detailed below:
LOOP 1
PANEL
NOTE: Repeat for
loops 2-4 if used
OUT +
OUT -
IN +
IN -
IN +
IN -
OUT +
OUT -
HUB
©2018 EMS Ltd. All rights reserved Page 4 of 6 MK254 Iss 3 18/09/2018 AJM
POWER
FAULT
ISOLATOR
ACTIVE
Fusion
Loop Module
POWER
FAULT
ISOLATOR
ACTIVE
Fusion
Loop Module
0.6m
2m
Fusion RLMs on Taktis - RLM location recap
Radio Loop Modules (RLMs) are powered from the Control Panel’s loop connection.
For optimum wireless performance, the following must be observed:
Ensure RLMs are installed as per the site survey
Ensure the Loop Module is not installed within 2m of other wireless or electrical
equipment (not including the Control Panel).
Ensure the Loop Module is not installed within 0.6m of metal work.
NEVER SITE AN RLM
NEAR METAL WORK OR
ELECTRICAL EQUIPMENT
©2018 EMS Ltd. All rights reserved Page 5 of 6 MK254 Iss 3 18/09/2018 AJM
LOOP 1
IN
OUT
Screen not connected
Single RLM
Ground-stud-terminal
of the cabinet-box
Multiple RLMs (max 5 per loop)
LOOP 1
IN
OUT
Screen not connected
RLM 1 RLM 2 RLM 3
Ground-stud-terminal
of the cabinet-box
Fusion RLMs on Taktis - wiring connections
Each RLM has connections: LOOP IN -, LOOP IN +, LOOP OUT -, LOOP OUT + and 2x
screen connections. The cable must be passed through the entry points provided.
Connections are detailed below:
The information contained within this literature is correct at time of publishing. EMS reserves the right to change any information regarding products as part of its continual development
enhancing new technology and reliability. EMS advises that any product literature issue numbers are checked with its head oce prior to any formal specication being written.
enquiries@emsgroup.co.uk
www.emsgroup.co.uk
+44 (0) 1227 369570
©2018 EMS Ltd. All rights reserved Page 6 of 6 MK254 Iss 3 18/09/2018 AJM
/