Xanté Impressia Digital Multi Media Press Owner's manual

Brand: Xanté

Model: Impressia Digital Multi Media Press

Type: Owner's manual

Turn the

Dial

Gap

Position

Turn the feeder “ON”. Turn the “SPEED”

dial as shown for a starting point of

envelope feeding. Press the “LOAD”

button for the envelopes to move forward.

Tighten the locking knob in place on the

alignment rail.

Impressia Feeder Guide

Feeder Alignment Media Side Guide

Move the feeder against the printer.

Position the feeder alignment tab against

the plastic located on the right side of the

By-Pass Tray.

Turn the feeder “OFF”. Using iQueue

workflow software set the “Media

Weight” to “Envelope”.

The media side guides can be adjusted side

to side for media width by using the locking

levers on the outer part of the guides.

Place the remaining amount of envelopes

in the side guides.

Loading Catalog Envelopes

Loading #10 Envelopes

Media Back Stop

Loading 4 Bar Envelopes

The back stop can be adjusted to apply

proper pressure and media angle.

Loading #10 Envelopes

Turn the feeder “OFF”.

Take one envelope,

flap up - flap last and place between the

media guides. Push the envelope under

the separator pads.

Tile a total of 2 envelopes and place them

on the feeder.

Place a handful of tiled envelopes on the

feeder on top of the tiled envelopes.

Hold the handful of envelopes in place

and slide the media back stop against the

the envelopes. Tighten the knob on the

rear side of the back stop.

Notice the position of the envelope and separator.

If the envelopes do not move to the end sensor, press

the load button again.

Notice the envelopes angled with the media guide.

Turn the feeder “OFF”. Adjust the

media side guides.

Take one envelope, flap up - flap last and

place between the media guides. Push the

envelope under the separator pads. Tile 2

envelopes and place them on the feeder.

Place a handful of tiled envelopes on the

feeder and slide the media back stop

against the envelopes. Tighten the

knob on the rear side of the back stop.

The feeder separator pads can be adjusted to

accommodate media thickness. When feeding

envelopes or thin media, the separator pads need

to be positioned near the bottom of the belt.

fig A

When feeding media that is thick or rigid, the

separator pads needs to be near the top of the

belt.

fig B The height of the pads can be adjusted

by loosening the center locking knob and raising

pads for the thicker media.

Envelopes or

Thin Media

Envelopes or

Thin Media

Thick

Media

Thick

Media

a) Dial at

normal

position

a) Dial at

normal

position

b) Dial

Turning

b) Dial

Turning

c) Dial

Gap

c) Dial

Gap

Bracket

Lever

Knob

Move the feeder away from the printer.

Open the printer side door.

Remove both fuser brackets from the

holders. Unlock both levers and slide

the fuser back to remove from the printer.

Turn the dial on the end of the fuser until

there is a small gap between the 2 dials.

Replace the fuser, press the levers down,

return the brackets, close the printer door

and put the feeder back into position.

Set the separator pads at half and adjust

the media side guides. Take one envelope,

flap up - flap last and place between the

media guides. Push the envelope under

the separator pads. Tile 2 envelopes and

place them on the feeder.

Place a handful of tiled envelopes on the

feeder and slide the media back stop

against the envelopes. Tighten the knob

on the rear side of the back stop.

Notice the gap position.

The envelopes will have curl before going into the

feeder, this will not effect envelopes being printed.

Depending on the envelopes type

style will determine

the amount that can loaded in a stack.

The separator pads height should be set

so the envelopes do not overlap on the

belts when feeding. Separators should

be adjusted as high as possible but still

able create media separation on the belt.

Separator Pads Adjustments

fig A

fig B

fig A

fig B

IMP Feeder Guide Rev 1.pdf

Xanté Impressia Digital Multi Media Press Owner's manual

Xanté Impressia Digital Multi Media Press Owner's manual

Xanté Impressia Digital Multi Media Press Owner's manual

Related papers

Other documents