Hytronik HCD405/BT User manual

  • Hello! I've reviewed the Installation and Instruction Manual for the HYTRONIK Motion Sensor HCD405/BT. This document provides detailed instructions on setting up and using the device, covering its technical specifications, wiring, detection patterns, and mobile app connectivity. I'm ready to assist with any questions you may have regarding this device, its features or installation process.
  • What is the maximum detection range of this sensor?
    What is the operating voltage?
    What is the operating temperature range?
5. Additional Information / Documents
1. For full explanation of Hytronik Photocell AdvanceTM technology, please kindly refer to www.hytronik.com/download ->knowledge ->Introduction of Photocell Advance
2. To learn more about detailed product features/functions, please refer to www.hytronik.com/download ->knowledge ->Introduction of App Scenes and Product Functions
3. Regarding precautions for Bluetooth product installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->Bluetooth Products - Precautions for Product Installation and Operation
4. Regarding precautions for microwave sensor installation and operation, please kindly refer to www.hytronik.com/download ->knowledge ->Microwave Sensors - Precautions for Product Installation and Operation
5. Data sheet is subject to change without notice. Please always refer to the most recent release on www.hytronik.com/products/bluetooth technology ->Bluetooth Sensors
6. Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy
HCD405BT-20230914-A0
To make or release the wire from the terminal, use a
screwdriver to push down the button.
1. 200 metres (total) max. for 1mm² CSA (Ta = 50)
2. 300 metres (total) max. for 1.5mm² CSA (Ta = 50)
1. Technical Specifications
Installation and Instruction Manual
Microwave Motion Sensor with 5.0 SIG Mesh HCD405/BT
HCD405BT-20230914-A0
2. Download the App
Free App for set-up and commissioning
3. Installation
Mechanical Structure & Dimensions
DALI Ouput
Wiring Diagram
Protocol
4 dBm
2.4 GHz - 2.483 GHz
Operation frequency
Transmission power
Range (Typical indoor)
10~30m
Stand-by power
Operating voltage
<
1W
220~240VAC 50/60Hz
20s
Warming-up
High Frequency (microwave
Sensor principle
5.0 SIG
Mesh
30°~150°
Ta:-20
O
C~+55
O
C
Detection angle
Operation temperature
IP20 IP rating
Detection range (Max.)* Installation Height : 6m
Detection Range (Ø) :10m (diameter)
Control Gear
Control Gear
L N DA- DA+
Control Gear
N
L
DA –
DA +
N
L
N
L
DA –
DA +
N
L
DA –
DA +
Ceiling mounted detection pattern (m)
Ceiling mounted height(m)
50
6
10%
30%
75%
50%
Wall mounted height (m)
Wall mounted detection pattern (m)
9
4
0
10%
30%
75%
50%
4. Detection Pattern
4.2
36.5
65
71.7
80.5
50
43.8
36.5
26
23.8
65
4.2
Antenna module
Photocell AdvanceTM
Daylight sensor
Bluetooth module
NL
DA–
DA+
Installation hole
Antenna module
Photocell AdvanceTM
Daylight sensor
NLInstallation
hole
DA–
DA+
Bluetooth module
Subject to change without notice. Subject to change without notice.
5.0 SIG mesh
Web app/platform: www.iot.koolmesh.com
Koolmesh Pro app for iPad
Smartphone app for both iOS & Android platform
for iOS for Android
for iPad
for Web
Web
iOS
Android
———This product should be installed by a qualified electrician.
DALI bus power supply
I guaranteed 30mA
I max: 80mA
Wire Preparation
0.75 - 1.5mm
8mm
/