Fire Magic Refreshment Center User manual

Fire Magic
Brand
Fire Magic
Model
Refreshment Center
Category
Security device components
Type
User manual
REV 1 - 1510081250
L-C2-388
1
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
Refreshment Center
Part # 3596A
Fig. 1-1 Replacement parts list
1
2
3
Item Description Part No. Qty.
1. Front panel 3596-05 1
2. Insulated lid 33596-05 1
3. Drain kit 3596-11 1
Table 1 - Replacement parts list
SPECIFICATIONS
Table 2 - Cut-out dimensions
Counter Cut-out Dimensions
A Counter Opening Height cut-out* 12"
B Counter Opening Width cut-out 25"
C Counter Opening Depth cut-out 25"
D Front panel width cut-out 26
1
/
8
"
*
Drain assembly clearances must also be provided.
TOP VIEW
Countertop
Lower support
Countertop
overhang
Front panel
ENCLOSURE
CUT-OUT
DIMENSIONS
Fig. 1-2
FRONT VIEW
B
C
D
See next page
for substrate
considerations
Countertop
overhang
X
TOP VIEW
SIDE VIEW
Countertop
overhang
(Front
panel)
(Countertop)
Y
1
/
4
"
Clearance
(Overhang)
X= D-B
÷
2
Y= Total
Countertop
Overhang
A
Front
panel
Check clearance for
front panel removal
COUNTERTOP OVERHANG
The front panel is designed to sit fl ush against the enclosure front wall. If the countertop extends beyond the front
wall, creating a countertop overhang, it must be cut fl ush with the front wall for the width of the front panel or a
gap will be created exposing the forward portions of the left and right side grill fi re walls. See illustrations above.
REV 1 - 1510081250
L-C2-388
2
SPECIFICATIONS (cont.)
SUBSTRATE
When adding any substrate to the enclosure front wall (including tiles, stone, etc.), consider the following:
Substrate Behind Front Panel
Substrate Alongside Front Panel
C
C
Flush
(Front panel)
(Countertop)
(Countertop)
(Front panel)
Substrate
(includes tiles,
etc. at front of
enclosure)
Countertop
overhang
(if applicable)
Flush
Refreshment
Center liner
Refreshment
Center liner
Substrate
(includes tiles,
etc. at front of
enclosure)
1
/4"
Clearance
Any additional substrate alongside the front panel does
not need to be considered in Dim. C (see previous
page), however a
1
/4" clearance on each side (same as
overhang) and below is required.
Substrate
+
countertop "front to back" cutout
must equate to Dim. C (see previous page)
when the substrate sits fl ush behind the
front panel.
Fig. 2-1 Fig. 2-2
Countertop
overhang
(if applicable)
TOP VIEW TOP VIEW
1
/4"
Clearance
INSTALLATION
Fig. 2-3 Plumbing installation
To drain
To unit
To install your Fire Magic Refreshment Center, follow the steps
below:
1. Prepare a cut-out in the countertop as specifi ed in Table
2 (reference Fig.1-2).
Important: Clearances below the unit must be provided for
the drain assembly.
2. Place the refreshment center into the cut-out opening. Use
silicone (between the hanger and countertop) to secure
the unit.
Important: Use care when handling the unit, so as to not
damage the pre-installed drain spout assembly.
DO NOT place the unit on a fl at surface prior to
installation.
3. Assemble and attach the supplied drain kit to the unit as
shown in Fig. 2-3. Plumb to a drain or as appropriate for
your installation. Observe all local codes.
REV 1 - 1510081250
L-C2-388
3
REMOVEABLE LID (OPTIONAL)
1. Remove screws from the soft down hinges on the inner left
and right side (see Fig. 3-1, A).
2. Firmly press the soft down hinges to the left until they clear
the bracket pins (see Fig. 3-1, B).
3. Slide the lid to the left to remove it from the unit (see Fig. 3-2).
To reattach the lid reverse the previous steps.
Fig. 3-1 Remove hinges
A
B
Fig. 3-2 Remove lid
REV 1 - 1510081250
L-C2-388
4
OPTIONAL FABRIC COVER
Fig. 4-1 Fabric cover option
An optional fabric cover is available to protect your unit when
not in use. Contact your local dealer for ordering information.
To install place the cover over the unit with the Fire Magic logo
facing upward. See Fig. 4-1.
Follow all instructions provided with the fabric cover.
Remove cover before use.
CARE & CLEANING
The appliance must be cleaned as often as once a month
(depending on use).
Clean your appliance by fi rst using grill cleaner. Always
wipe with the grain (See Fig. 4-2). Next, use stainless
steel cleaner to restore the stainless steel color. Finish by
wiping your appliance down using polish wipes.
If your appliance is installed in a seaside (salt air) or
poolside (chlorine) location, it will be more susceptible to
corrosion and must be maintained/cleaned more frequently.
Do not store chemicals (such as chlorine or fertilizer) near
your stainless steel appliance.
Due to the nature of stainless steel, surface iron oxide
deposits may appear. Do not be alarmed – these deposits
are removable with stainless steel cleaner through prompt
and periodic maintenance. If not attended to promptly,
permanent pitting may occur.
By following these recommendations, you will enjoy the
beauty and convenience of your appliance for many years
to come.
Wipe with grain
Fig. 4-2 Wipe with grain
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Fire Magic Refreshment Center User manual

Fire Magic
Brand
Fire Magic
Model
Refreshment Center
Category
Security device components
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents