Gamber-Johnson 7160-0162 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0162
Category
Mounting kits
Type
Installation guide

This manual is also suitable for

Gamber-Johnson 7160-0162 is a small clevis designed to be mounted on a DS pole, a DS Arm, or a customer supplied mount. It is capable of supporting a maximum unit weight of three pounds. The clevis comes with two nylon flat bearings, a bearing clamp, three ¼-20x0.75 carriage bolts, and three ¼-20 nylon lock nuts. It can be installed on a DS-Upper plate or a DS-Arm. For DS-Upper plate installation, the bearings, bearing clamp, and carriage bolts are used to assemble the clevis to the plate. For DS-Arm installation, only the nylon lock nuts are used to assemble the clevis to the arm.

Gamber-Johnson 7160-0162 is a small clevis designed to be mounted on a DS pole, a DS Arm, or a customer supplied mount. It is capable of supporting a maximum unit weight of three pounds. The clevis comes with two nylon flat bearings, a bearing clamp, three ¼-20x0.75 carriage bolts, and three ¼-20 nylon lock nuts. It can be installed on a DS-Upper plate or a DS-Arm. For DS-Upper plate installation, the bearings, bearing clamp, and carriage bolts are used to assemble the clevis to the plate. For DS-Arm installation, only the nylon lock nuts are used to assemble the clevis to the arm.

7160-0162
INSTALLATION INSTRUCTIONS
Product Revision Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Small Clevis
Rev. A
INST-420
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© copyright 2012 Gamber-Johnson, LLC
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
The small clevis is to be mounted on a DS pole, a DS Arm, or a customer supplied
mount.
CAUTION: The small clevis is rated to support a maximum unit weight of three pounds.
Additional weight beyond three pounds may cause deformation in the small clevis
during large sudden impacts.
Figure 1 DS-Upper Install
Figure 2 DS-Arm Install
1/4-20 Nylon Lock Nut
DS-Upper Install
1. Assemble the small clevis with the supplied (2) nylon flat bearings and (1) bearing clamp
to the DS-Upper plate with the supplied (3) ¼-20x0.75 carriage bolts and (3) ¼-20 nylon
lock nuts as shown in Figure 1.
DS-Arm Install
1. Discard the supplied nylon flat bearings, bearing clamp, and carriage bolts.
2. Assemble the small clevis to the DS-Arm with the supplied (3) ¼-20 nylon lock nuts as
shown in Figure 2.
1/4-20x0.75 Carriage Bolt
Nylon Flat Bearing
Nylon Flat Bearing
Bearing Clamp
1/4-20 Nylon Lock Nut
  • Page 1 1

Gamber-Johnson 7160-0162 Installation guide

Gamber-Johnson
Brand
Gamber-Johnson
Model
7160-0162
Category
Mounting kits
Type
Installation guide
This manual is also suitable for

Gamber-Johnson 7160-0162 is a small clevis designed to be mounted on a DS pole, a DS Arm, or a customer supplied mount. It is capable of supporting a maximum unit weight of three pounds. The clevis comes with two nylon flat bearings, a bearing clamp, three ¼-20x0.75 carriage bolts, and three ¼-20 nylon lock nuts. It can be installed on a DS-Upper plate or a DS-Arm. For DS-Upper plate installation, the bearings, bearing clamp, and carriage bolts are used to assemble the clevis to the plate. For DS-Arm installation, only the nylon lock nuts are used to assemble the clevis to the arm.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents