Defiant DF-5716-BK-A Operating instructions

Type
Operating instructions

This manual is also suitable for

Defiant DF-5716-BK-A is a motion sensor that can be used to automatically turn on lights when motion is detected. It has a range of up to 100 ft. and a sensing angle of up to 270°. It can be used with incandescent bulbs up to 300 watts. The motion sensor has three operating modes: Test, Auto, and Manual. In Test mode, the light will stay on for 5 seconds after all motion has stopped. In Auto mode, the light will turn on when motion is detected and will stay on for the amount of time set by the "ON-TIME" switch.

Defiant DF-5716-BK-A is a motion sensor that can be used to automatically turn on lights when motion is detected. It has a range of up to 100 ft. and a sensing angle of up to 270°. It can be used with incandescent bulbs up to 300 watts. The motion sensor has three operating modes: Test, Auto, and Manual. In Test mode, the light will stay on for 5 seconds after all motion has stopped. In Auto mode, the light will turn on when motion is detected and will stay on for the amount of time set by the "ON-TIME" switch.

THANK YOU
We appreciate the trust and condence you have placed in Deant through the purchase of this motion sensor. We
strive to continually create quality products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing Deant!
USE AND CARE GUIDE
REPLACEMENT MOTION SENSOR
Questions, problems, missing parts? Before returning to the store,
call Deant Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
1-866-308-3976
HOMEDEPOT.COM
Item #101240
745407
Model #DF-5716-BK-A
DF-5716-WH-C
2
Table of Contents
Table of Contents ......................................2
Safety Information ....................................2
Precautions ............................................2
Warranty ...................................................2
2-Year Warranty .....................................2
Specifications ...........................................3
Pre-Installation .........................................3
Planning Installation ..............................3
Tools Required .......................................3
Hardware Included .................................4
Package Contents ..................................4
Installation ................................................5
Operation...................................................6
Care and Cleaning ....................................8
Troubleshooting ........................................9
Safety Information
PRECAUTIONS
Please read and understand this entire manual before
attempting to assemble, install, or operate this motion
sensor.
This motion sensor requires 120-volts AC.
Some codes require installation by a qualied electrician.
This motion sensor must be properly grounded.
For proper operation, this motion sensor should be:
Ƒ Installed outdoors to a wall or eaves
Ƒ Installed 8 ft. (2.4 m) above the ground (If
the motion sensor is mounted higher than
recommended, aiming the sensor down will reduce
the coverage area.)
Ƒ Do not leave the “ON-TIME” switch in the “TEST”
position. The frequent ON/OFF cycling of the light
xture will reduce the life of the bulb
WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light xture.
CAUTION: Keep the motion sensor at least 1 in. (25 mm)
away from standard PAR38 bulbs.
CAUTION: Keep the motion sensor at least 2 in. (50 mm)
away from halogen bulbs.
CAUTION: To avoid water damage and the risk of
electrical shock, the motion sensor controls must be facing
the ground when the installation is complete.
CAUTION: Burn hazard. Allow the light xture and the
bulb to cool before touching.
NOTICE: Do not connect this motion sensor to a dimmer switch
or timer.
Warranty
2-YEAR WARRANTY
Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com.
3 HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
Specications
Range
Up to 100 ft. (30 m) - Varies with surrounding temperature
Sensing angle
Up to 270°
Electrical load - incandescent
Up to 300 watt maximum (Up to 150 watt maximum per bulb
holder)
Power requirements
120 VAC, 60 Hz
Operating modes
Test, Auto, Manual
Bulb modes
Security, BulbSaver, AlertFlash
Time delay
1, 5, 20 minutes
DualBrite timer
Off, 3 hours, 6 hours, dusk-to-dawn
Pre-Installation
PLANNING INSTALLATION
Before installing the motion sensor, ensure that all parts are present (see Hardware Included on page 4). If any part
is missing or damaged, do not attempt to assemble, install, or operate this motion sensor.
Estimated installation time: 30 minutes
TOOLS REQUIRED
Phillips
screwdriver
Flathead
screwdriver
Pliers
Wire strippers/
cutters
Circuit tester Work gloves
Electrical tape Silicone sealant Ladder
Safety goggles
4
Pre-Installation (continued)
HARDWARE INCLUDED
NOTE: Hardware shown to actual size.
AA
Part Description Quantity
AA Wire connector 4
PACKAGE CONTENTS
Part Description Quantity
A Motion sensor 1
NOTE: If the motion sensor (A) pops out of the ball joint,
loosen the clamp screw, push the motion sensor (A) back
into the ball joint, and tighten the clamp screw. Do not
overtighten.
A
5 HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
Installation
1
Installing the Motion Sensor
WARNING: Turn the power off at the circuit breaker or
fuse. Place tape over the circuit breaker switch and verify
power is off at the light xture.
The WHITE motion sensor wire is neutral. The BLACK
motion sensor wire is hot. The RED motion sensor wire
is switched “hot”.
Ƒ Remove the existing light xture.
Ƒ Route the motion sensor wires through the
canopy (1) of the existing light xture.
Ƒ Screw the motion sensor (A) into the canopy
(1) of the existing light xture.
2
Wiring the Motion Sensor
Ƒ Connect the motion sensor wires to the light
xture wires and the junction box wires with
wire connectors (AA):
Ƒ White to white
Ƒ Black motion sensor wire to black junction
box wire
Ƒ Red motion sensor wire to black bulb
holder (2) wires
Ƒ Bare or green ground wire to house ground
and any light xture ground wire or ground
screw, if present
Ƒ Follow the instructions that came with the
existing light xture to mount and adjust the
light xture.
OR
FR
ONT
A
AA
AA
AA
A
A
2
2
2
2
1
AA
6
Operation
1
Adjusting the Motion Sensor
CAUTION: Keep the motion sensor at least 1 in. (25 mm)
away from standard PAR38 bulbs.
CAUTION: Keep the motion sensor at least 2 in. (50 mm)
away from halogen bulbs.
CAUTION: To avoid water damage and risk of electrical
shock, the motion sensor controls must be facing the
ground when installation is complete.
Ƒ Turn the power on at the circuit breaker or fuse
and turn on the wall switch.
Ƒ Loosen the lock nut (3) and screw (4) to adjust
the motion sensor (A) for the desired coverage.
Ƒ Rotate the motion sensor (A) so the controls
face toward the ground.
Ƒ Tighten the lock nut (3) and screw (4).
NOTICE: All clearances must be maintained. See Safety Information
on page 2.
2
Setting the Sensor for Testing
When the “ON-TIME” switch is set to the “TEST”
position, the light xture will operate during the day
or night. The light will stay on for 5 seconds after all
motion is stopped.
Ƒ Set the “ON-TIME” switch to the “TEST”
position.
Ƒ Set the “DUALBRITE” switch to the “OFF”
position.
Ƒ Turn the “RANGE” dial to the “MIN” position.
Ƒ Aim the motion sensor (A) in the general
direction of the area to be covered.
NOTE: The motion sensor will need to completely warm
up (90 seconds) before beginning the setup process.
LAMP MODE
NORMAL SOFT FLASH
ON-TIME DUAL BRITE™
TEST 1 5 20
MINUTES
OFF 3 6 DUSK TO
HOUR DAWN
MAXMIN
RANGE
A
A
3
4
7 HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
Operation (continued)
3
Adjusting the Motion Sensor
Detection Zone
Ƒ Turn on the circuit breaker or fuse and the light
switch.
Ƒ Perform a “walk test”. Walk in an arc across
the front of the motion sensor (A).
Ƒ Watch the light. The light will come on and the
red LED will ash indicating motion has been
detected.
Ƒ Stop, wait for the light to turn off, and then
begin walking again.
Ƒ Continue this process until the detection zone
has been established.
Ƒ Adjust the sensor up, down, or side to side to
change the motion sensor (A) detection zone.
4
Adjusting the RANGE Dial
Ƒ To increase the detection zone, turn the
“RANGE” dial toward the “MAX” position.
Ƒ To decrease the detection zone, turn the
“RANGE” dial toward the “MIN” position.
NOTE: The motion sensor (A) is more sensitive to motion
moving across the front of the sensor. The motion sensor
(A) is less sensitive to motion moving directly toward the
front of the sensor.
NOTE: The higher the “RANGE” setting (sensitivity), the
greater the possibility of false triggering. To reduce false
triggering, rotate the “RANGE” control toward the “MIN”
setting.
MAXMIN
RANGE
5
Adjusting the ON-TIME Switch
The “ON-TIME” switch determines the amount of time
the light will stay on full bright after all motion has
stopped.
Ƒ Set the “ON-TIME” switch to the 1, 5, or 20
minute position.
LAMP
M
NORMAL S
O
ON-TIME
TEST 1 5 20
MINUTES
MAXMIN
RANGE
6
Adjusting the DUALBRITE
Switch
The “DUALBRITE” switch determines the amount of
time the lights stay on at a reduced light level after
sundown. Switching this setting to “OFF” will not
effect the “ON-TIME” setting.
Ƒ Set the “DUALBRITE” switch to OFF, 3 hours, 6
hours, or dusk-to-dawn (sunset to sunrise).
M
ODE
O
FT FLASH
DUAL BRITE™
OFF 3 6 DUSK TO
HOUR DAWN
A
A
A
A
8
Operation (continued)
7
Adjusting the LAMP MODE
Switch
The “LAMP MODE” switch determines the way the
lights will turn on when motion is detected.
Ƒ Security (“NORMAL”) - Light comes on instantly.
Ƒ BulbSaver (“SOFT”) - Light comes on dim and
gradually increases to full brightness. When the
light turns off it will gradually dim to half-bright,
pause, and then will continue dimming until the
light turns off.
Ƒ AlertFlash (“FLASH”) - Light ashes on then off
twice before turning on full brightness.
Ƒ Set the “LAMP MODE” to “NORMAL”, “SOFT”,
or “FLASH” position.
LAMP MODE
NORMAL SOFT FLASH
8
Using Manual Mode
Manual mode overrides the motion sensor (A) and
“ON-TIME” control so the light will operate full bright.
This feature only works at night and only for one night
at a time. The motion sensor (A) will reset to motion
sensing mode at sunrise. Manual mode can be toggled
on and off using a wall switch.
Ƒ To turn manual mode on, switch the light off
at the wall switch for 3 to 4 seconds and then
back on.
Ƒ To turn manual mode off, switch the light off
at the wall switch for 3 to 4 seconds and then
back on.
NOTE: If the power to the light xture is off for more than
5 seconds, allow the motion sensor to warm up prior to
switching to manual mode.
Turn the switch
OFF for 3 to 4
seconds
Turn the
switch
back ON
Care and Cleaning
Ƒ To prolong the original appearance, clean with clear water and a soft, damp cloth only.
Ƒ Do not use paints, solvents, or other chemicals on this motion sensor. They could cause a premature
deterioration of the nish. This is not a defect in the nish and will not be covered by the warranty.
Ƒ Do not spray with a hose or power washer.
A
9 HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
Troubleshooting
Problem Possible Cause Solution
The light will not come on. Ƒ The light switch is turned off. Ƒ Turn the light switch on.
Ƒ The bulb is loose or burned out. Ƒ Check the bulb and replace
if burned out.
Ƒ The fuse is blown or the circuit breaker
is turned off.
Ƒ Replace the fuse or turn the
circuit breaker on.
Ƒ Daylight turn-off (photocell) is in effect. Ƒ Recheck after dark.
Ƒ The circuit wiring is incorrect, if this is
a new installation.
Ƒ Verify the wiring is correct.
Ƒ The motion sensor is aimed in the
wrong direction.
Ƒ Re-aim the motion sensor
to cover the desired area.
Ƒ The outside air temperature is close to
the same as a person’s body heat.
Ƒ Increase the “RANGE”
setting.
The light comes on during the
day.
Ƒ The motion sensor may be installed in a
relatively dark location.
Ƒ The motion sensor is oper-
ating normally under these
circumstances.
Ƒ The “ON-TIME” switch is in the “TEST”
position.
Ƒ Set the “ON-TIME” switch
to the 1, 5, or 20 minute
setting.
The light comes on for no
apparent reason.
Ƒ The motion sensor may be sensing
small animals or automobile trafc.
Ƒ Re-aim the motion sensor.
Ƒ The “RANGE” dial is set too high. Ƒ Decrease the “RANGE”
setting.
Ƒ The “DUALBRITE” switch is in the 3
hour, 6 hour, or dusk-to-dawn setting.
Ƒ The motion sensor is oper-
ating normally under these
circumstances.
Ƒ The outside temperature is much
warmer or cooler than a person’s body
heat (summer or winter).
Ƒ Decrease the “RANGE”
setting.
Ƒ The motion sensor is wired through a
dimmer or timer.
Ƒ Do not use a dimmer or
timer to control the motion
sensor. Replace the dimmer
or timer with a standard on/
off wall switch.
The lights turn off too late in
Dusk-to-Dawn setting.
The motion sensor may be installed in a
relatively dark location.
Relocate the motion sensor or
use the 3 hour or 6 hour setting.
10
Troubleshooting (continued)
Problem Possible Cause Solution
The lights stay on continuously. Ƒ A bulb is positioned too close to the
motion sensor or pointed at nearby
objects that cause heat to trigger the
motion sensor.
Ƒ Reposition the bulb away
from the motion sensor or
nearby objects.
Ƒ The motion sensor may be picking up
a heat source like an air vent, dryer
vent, or brightly painted, heat-reective
surface.
Ƒ Decrease the “RANGE”
setting or reposition the
motion sensor.
Ƒ The motion sensor is in manual mode. Ƒ Switch the motion sensor
to auto. See Using Manual
Mode on page 8.
Ƒ The motion sensor is wired through a
dimmer or timer.
Ƒ Do not use a dimmer or
timer to control the motion
sensor. Replace the dimmer
or timer with a standard on/
off wall switch.
Ƒ The motion sensor is on the same
circuit as a motor, transformer, or
uorescent bulb.
Ƒ Install the motion sensor
on a circuit without motors,
transformers, or uorescent
bulbs.
The lights ash on and off. Ƒ Heat or light from the bulbs may be
turning the motion sensor on and off.
Ƒ Reposition the bulbs away
from the motion sensor.
Ƒ Heat is being reected from other
objects and may be turning the motion
sensor on and off.
Ƒ Reposition the motion
sensor.
Ƒ The motion sensor is in “TEST” mode
and warming up.
Ƒ Flashing is normal under
these conditions.
Ƒ Light may be leaking through the bulb
reectors.
Ƒ Replace the bulbs with new
high quality PAR 38 bulbs.
Ƒ The motion sensor is in AlertFlash
(“FLASH”) mode.
Ƒ Flashing is normal in this
mode. Select Security
(“NORMAL”) or BulbSaver
(“SOFT”) mode to turn
ashing off.
The lights ash once then stay
off in manual mode.
The motion sensor is detecting light from
the bulbs.
Reposition the bulbs to keep the
area below the motion sensor
relatively dark.
11 HOMEDEPOT.com
Please contact 1-866-308-3976 for further assistance.
Questions, problems, missing parts? Before returning to the store,
call Deant Customer Service
8 a.m.-6 p.m., EST, Monday-Friday
1-866-308-3976
HOMEDEPOT.COM
Retain this manual for future use.
205217-05A
¿Tiene preguntas, problemas o piezas faltantes? Antes de la devolución al almacén llame al
Servicio al Cliente de Deant de
8 a.m.-6 p.m., Hora del Este, de lunes a viernes.
1-866-308-3976
HOMEDEPOT.COM
Guarde este manual para uso futuro.
205217-05A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Defiant DF-5716-BK-A Operating instructions

Type
Operating instructions
This manual is also suitable for

Defiant DF-5716-BK-A is a motion sensor that can be used to automatically turn on lights when motion is detected. It has a range of up to 100 ft. and a sensing angle of up to 270°. It can be used with incandescent bulbs up to 300 watts. The motion sensor has three operating modes: Test, Auto, and Manual. In Test mode, the light will stay on for 5 seconds after all motion has stopped. In Auto mode, the light will turn on when motion is detected and will stay on for the amount of time set by the "ON-TIME" switch.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI