C2G 26854 Owner's manual

C2G
Brand
C2G
Model
26854
Category
Cable network testers
Type
Owner's manual
bad
=
mix light
=bad
=
green light
no light
red light
good
=
bad
5
GND
7
8
2
3
6
4
1
5
GND
8
7
2
4
6
3
1
5
GND
8
7
4
6
3
2
1
5
GND
7
8
3
6
4
1
2
5
GND
7
8
3
6
4
1
2
5
GND
8
7
3
4
6
2
1
Green=Good No light=Open
Network Cable Terminator
4-5
NetworkCableTester-E
Red or mix=Bad
1-2
3-6
GND
7-8
Red or mix=Bad
Green=Good No light=Open
Network Cable Terminator
1-2
NetworkCableTester-E
GND
7-8
4-5
3-6
Network Cable Terminator
Green=Good No light=Open
NetworkCableTester-E
Red or mix=Bad
3-6
4-5
1-2 GND
7-8
The Network Cable Tester-Pro is designed to test quickly, the most popular cable wiring that uses twisted
pairs, such as TIA568A/568B,Token Ring and 10/100BASE-T (STP/UTP) . It will automatically test the
cables once they are plugged into the master and remote unit and the power turned on. It will also test
coaxial cables. It can test CAT 5 & 6 cables for continuity, miss wiring, reversed and ground by the
following test procedures.
Network Cable Tester-Pro Model No. 251451/Pro
Continuity test :
Step 1. Install the 9V alkaline battery in the rear battery compartment.
Step 2. Plug both ends of the RJ-45 or BNC cable into the sockets of the tester. One in the Master unit and
the other into the remote unit
Step 3. After the cable is plugged into the tester, turn on the power and the unit will continuously auto
scan the wires. The LED's on the tester will turn either green, red or no LED. Any LED'S not green
show a fault on the twisted pair. Pressing the Ground button will tell you if any wires are ground .
A green light on the BNC cable means the cable is good while a red light means the cable is bad.
RJ-45 Fault Status Red : Short, Reversed or Miss wire
RJ-45 Fault Status No Light : Open
BNC Fault Status Red Light : Short
Any LED's displaying red or no lights mean the cable is miss-wired, open or shorted or
reversed. Check the cable connections again and start the tests again from Step 2.
Features a Remote
Unit that slides onto
the Master Unit
7
6
16
13
9
NOT FOR LIVE CIRCUITS
2
1
14
BADOK
BNC
12
11
Green=Good No light=Open
Red or mix=Bad
Network Cable Terminator
NetworkCableTester-Pro
10
GND
5
3-6
1-2
POWER
GND
7-8
4-5
8
15
4
3
1 Master Unit RJ-45 socket
2 Master Unit BNC
3 Remote Unit RJ-45 socket
4 Remote Unit BNC
5 Pair 1-2 good/bad LED
6 Pair 3-6 good/bad LED
7 Pair 4-5 good/bad LED
8 Pair 7-8 good/bad LED
9 Ground
10 Check ground on/off
11 Power on/off
12 Power on flashing LED.
13 BNC good LED
14 BNC bad LED
15 Remote Unit
16 Master Unit
5
2
6
11
1
NOT FOR LIVE CIRCUITS
NetworkCableTester-E
NO LIGHT=OPEN
RED=BAD
GREEN=GOOD
9
10
GND
NO LIGHT=BAD
GREEN=GOOD
1-2
7-8
4-5
3-6
BNC
4
7
8
3
1 Master Unit RJ-45 socket
2 Master Unit BNC
3 Remote Unit RJ-45 socket
4 Remote Unit BNC
5 Pair 1-2 good/bad LED
6 Pair 3-6 good/bad LED
7 Pair 4-5 good/bad LED
8 Pair 7-8 good/bad LED
9 Ground
10 Remote Unit
11
Master Unit
3
7
GND
8
4
6
5
2
1
3
7
GND
8
6
4
5
1
2
GND
4
6
3
2
1
8
7
5
3
GND
7
8
6
4
5
1
2
The Network Cable Tester-E is designed to test quickly, the most popular cable wiring that uses twisted
pairs, such as TIA568A/568B,Token Ring and 10/100BASE-T (STP/UTP). It will automatically test the
cables once they are plugged into the master and remote unit. It will also test coaxial cables. It can test
CAT 5 & 6 cables for shorts, miss wiring, reversed and ground by the following test procedures.
Network Cable Tester - E Model No. 251450/E
Continuity test:
Step 1. Install the 9V alkaline battery in the rear battery compartment.
Step 2. Plug both ends of the RJ-45 or BNC cable into the sockets of the tester. One in the Master unit and
the other into the remote unit
Step 3. After the cable is plugged into the tester, the LED's on the tester will turn either green, red or no
light. Any LED'S not green show a fault on the twisted pair. A green light on the BNC cable means
the cable is good while a no light means the cable is bad.
RJ-45 Fault Status Red : Short, Reversed or Miss wire
RJ-45 Fault Status No Light : Open
BNC Fault Status No Light : Short Open
Any LED's displaying red or no lights mean the cable is miss-wired, open or shorted or reversed.
Check the cable connections again and start the tests from Step 2.
Features a Remote
Unit that slides onto
the Master Unit
NetworkCableTester-E
7-8
GREEN=GOOD
NO LIGHT=BAD
BNC
3-6
4-5
1-2 GND
NetworkCableTester-E
NO LIGHT=BAD
GREEN=GOOD
7-8
1-2
4-5
3-6
BNC
GND
3
GND
7
8
6
4
5
1
2
3
8
7
GND
5
4
6
2
1
NetworkCableTester-E
BNC
3-6
1-2 GND
4-5
7-8
GREEN=GOOD
NO LIGHT=BAD
=
green light
=bad
no light
red light
=
bad
good
  • Page 1 1
  • Page 2 2

C2G 26854 Owner's manual

C2G
Brand
C2G
Model
26854
Category
Cable network testers
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents