Fender 800 Pro Owner's manual

Page is loading ...

3

Important Safety Instructions

This symbol warns the user of dangerous voltage levels

localized within the enclosure.

This symbol advises the user to read all accompanying

literature for safe operation of the unit.

∆ Read, retain, and follow all instructions. Heed all warnings.

∆ Only connect the power supply cord to an earth grounded AC

receptacle in accordance with the voltage and frequency ratings

listed under INPUT POWER on the rear panel of this product.

∆ WARNING: To prevent damage, fire or shock hazard, do not

expose this unit to rain or moisture.

∆ Unplug the power supply cord before cleaning the unit exterior

(use a damp cloth only). Wait until the unit is completely dry

before reconnecting it to power.

∆ Maintain at least 6 inches (15.25 cm)of unobstructed air space

behind the unit to allow for proper ventilation and cooling of the

unit.

∆ This product should be located away from heat sources such as

radiators, heat registers, or other products that produce heat.

∆ This product may be equipped with a polarized plug (one blade

wider than the other). This is a safety feature. If you are unable

to insert the plug into the outlet, contact an electrician to replace

your obsolete outlet. Do not defeat the safety purpose of this

plug.

∆ Protect the power supply cord from being pinched or abraded.

∆ This product should only be used with a cart or stand that is

recommended by the manufacturer.

∆ The power supply cord of this product should be unplugged from

the outlet when left unused for a long period of time, or during

electrical storms.

∆ This product should be serviced by qualified service personnel

when: the power supply cord or the plug has been damaged; or

objects have fallen, or liquid has been spilled onto the product;

or the product has been exposed to rain; or the product does not

appear to operate normally or exhibits a marked change in

performance; or the product has been dropped, or the enclosure

damaged.

∆ Do not drip nor splash liquids, nor place liquid filled containers on

the unit.

∆ CAUTION: No user serviceable parts inside, refer servicing to

qualified personnel only.

∆ Fender

®

amplifiers and loudspeaker systems are capable of

producing very high sound pressure levels which may cause

temporary or permanent hearing damage. Use care when

setting and adjusting volume levels during use.

Instrucciones de seguridad importantes

Este símbolo advierte al usuario que en el interior de la

carcasa hay niveles peligrosos de voltaje.

Este símbolo advierte al usuario que lea toda la

documentación adjunta para utilizar la unidad con

seguridad.

∆ Lea las instrucciones atentamente y sígalas al pie de la letra.

Tenga en cuenta todas las advertencias.

∆ Conecte el cable de alimentación eléctrica únicamente a una

toma de CA de acuerdo con las especificaciones de voltaje y

frecuencia indicadas en la entrada INPUT POWER del panel

posterior de este producto.

∆ ADVERTENCIA: Para evitar daños, incendios y descargas

eléctricas, no exponga esta unidad a la lluvia ni a la humedad.

∆ Antes de limpiar el exterior de la unidad, desconecte el cable de

alimentación (utilice únicamente un paño húmedo). Deje que la

unidad se seque completamente antes de volver a conectarla a

la corriente.

∆ Asegúrese de que haya al menos 6 pulgadas (15 cm) de espacio

libre en la parte posterior de la unidad para una correcta

ventilación y refrigeración.

∆ Este producto deberá estar situado lejos de fuentes de calor

tales como radiadores, registros de calefacción u otros

productos que generen calor.

∆ Es posible que este producto esté equipado con un enchufe

polarizado (una patilla más ancha que otra) para una mayor

seguridad. Si no puede introducir el enchufe en la toma de

corriente, póngase en contacto con un electricista para que la

cambie, ya que podría no ser compatible. No modifique la

función de seguridad de este enchufe.

∆ Tenga cuidado de no pellizcar ni rozar el cable de alimentación.

∆ Este producto sólo se debe utilizar con el soporte recomendado

por el fabricante.

∆ El cable de alimentación de este producto deberá estar

desconectado de la toma de corriente cuando no se vaya a

utilizar durante un período de tiempo largo o durante tormentas

con aparato eléctrico.

∆ Este producto deberá ser reparado por personal cualificado en

los siguientes casos: si el cable de alimentación o el enchufe

está dañado; si se ha caído algún objeto o se ha derramado

líquido sobre el producto; si el producto ha estado expuesto a la

lluvia; si su funcionamiento y rendimiento no son normales; si ha

sufrido algún golpe o la caja esta dañada.

∆ Evite que se moje la unidad y no ponga recipientes con líquido

sobre ella.

∆ ADVERTENCIA: En el interior de la unidad existen piezas cuya

reparación sólo la puede realizar personal cualificado.

∆ Los sistemas de amplificadores y altavoces Fender

®

pueden

producir niveles muy elevados de sonido, que pueden provocar

daños temporales o permanentes en el oído. Tenga cuidado al

establecer y ajustar los niveles de volumen durante la utilización.

Page is loading ...

wwwwww

..

ffeennddeerr..ccoomm

✧

wwwwww

..mmrrggeeaarrhheeaadd..nneett

PP

aa

nn

ee

ll

CC

oo

nn

tt

rr

oo

ll

ss

Your new 800 Pro™ bass amplifier delivers world-class

Fender

®

tone and world-standard Fender

®

quality:

• 1200 Watts output power into 2Ω, (800 Watts into 4Ω)

• 3-BAND SEMI-PARAMETRIC EQUALIZER

• EQ ON/OFF from the front panel or remote footswitch

• EQ GAIN for equal or alternate EQ on/off volume levels

• ROOM BALANCE compensates for dark or bright acoustics

• ENHANCE enhances bass and treble frequencies

• BASS/TREBLE traditional tone controls

• COMPRESSOR provides variable sound smoothing

• Amplifier MUTE allows silent inline instrument tuning with

your tuner plugged into TUNER OUT

• EFFECTS LOOP jacks for connecting your effects device or

auxilliary amplifier

• PASSIVE/ACTIVE switch accomodates a normal– or

high–output bass

• Balanced XLR LINE OUT jack with LEVEL control, GROUND

LIFT and PRE/POST EQ selector for output to sound

reinforcement or recording equipment

• Both Speakon® and 1/4" outputs offer maximum flexibility

Thank you for choosing Fender

®

—T

one, T

radition and Innovation—since 1946

A. INPUT - Plug your bass in here.

B. PASSIVE/ACTIVE - Selects pickup type (sensitivity):

PASSIVE - normal (full input sensitivity)

ACTIVE - pre–amplified (low input sensitivity)

C. GAIN - Adjusts the preamp signal level. Use together with

MASTER VOLUME {L} to set the overall amplifier

loudness. Watch the PRE AMP LEDs to determine the

optimal GAIN setting:







PRE AMP CLIP - Indicates preamp clipping

(distortion). Occasional flashing is normal at peak playing

intensities – reduce GAIN if unwanted distortion is heard

while this LED is on.







PRE AMP SIGNAL - Indicates the presense of

sufficient signal strength. Constant illumination is normal

at moderate playing intensities – increase GAIN and/or

instrument volume if this LED is off or only flashing.

D. ROOM BALANCE - Rotate clockwise for treble emphasis

to compensate for soft acoustic surfaces (carpet/drapes).

Rotate counter–clockwise for bass emphasis to

compensate for hard acoustic surfaces (cement/tile).

E. ENHANCE - Boosts low and high frequencies.

OFF - Useful for finger–style bass playing

ON - Useful for slap–style/deep–tone bass playing

F. BASS/TREBLE - Adjusts tone in low/high frequency

bands respectively.

G. SEMI-PARAMETRIC EQUALIZER - Adjusts

tone in three variable frequency bands. Each

FREQ knob selects the center of frequency

range that the LEVEL knob below adjusts.

NOTE: The EQ has no effect when all LEVEL

knobs are set to “0.”

H. EQ GAIN - Adjusts the signal level of the semi-parametric

equalizer circuit when active ( EQ ON). Useful for

setting a balance between EQ on and off volume levels.

I. EQ ON/OFF - Switches the semi-parametric equalizer

on/off as indicated by the LED.

J. COMPRESSOR - Compresses the dynamic range of the

signal to smooth volume peaks and increase sustain.

Rotate fully counter-clockwise to disable the compressor.

K. MUTE - Disables all amplifier outputs except for TUNER

OUT. LED flashes when MUTE is active.

L. MASTER VOLUME - Adjusts overall amplifier loudness in

conjunction with GAIN {C}. Watch the PWR AMP LED to

determine the optimal MASTER VOLUME setting:







PWR AMP CLIP - Indicates power amp clipping

(distortion). Occasional flashing is normal at peak playing

intensities. Reduce MASTER VOLUME if unwanted

distortion is heard while this LED is on.

M. POWER - Switches the unit on/off as indicated by the LED.

6

FF

ee

nn

dd

ee

rr

®

88

00

PP

rr

oo

AA

mm

pp

ll

ii

ff

ii

ee

rr

PLEASE NOTE: Your 800 Pro is shipped with adhesive rubber feet for non-rack mount applications. Remove feet

prior to rack mounting.

O. PARALLEL SPEAKER OUTPUTS - Connect one of four

speaker configurations to meet the 2–ohm minimum load

requirement using any combination of 4–pole Speakon®

and 1/4" output jacks:

1) one 2–ohm speaker

2) two 4–ohm speakers

3) one 4–ohm and two 8–ohm speakers

4) four 8–ohm speakers

P. IEC POWER SOCKET - Connect only the supplied special

high-capacity power cord to a grounded AC receptacle in

compliance with the voltage and frequency ratings

specified on the rear panel of your amplifier.

Q. EFFECTS LOOP - (1) Ef

fects Loop - Connect SEND to the

input of your effects device and the output of the effects

device to RETURN. (2) Multiple Pr

o™ Amps - Connect

SEND on the primary unit to RETURN on the auxiliary unit.

The primary unit controls all auxiliary units.

R. FOOTSWITCH - Connect the included footswitch to

enable remote on/off switching of the semi-parametric

equalizer. NOTE: When connected, the footswitch

overrides EQ ON/OFF {I} on the front panel.

S. TUNER OUT - Connect your bass tuner to enable inline

instrument tuning (see MUTE {K}).

T. GROUND LIFT - Disconnects the LINE OUT {V} ground

connection (pin-1) which may reduce noise levels.

GROUNDED (normal) GROUND LIFTED

U. LINE OUT LEVEL - Adjusts the output level of the LINE

OUT jack.

V. LINE OUT - Balanced XLR jack for output to sound

reinforcement/recording equipment.

W. PRE/POST EQ - Supplies the LINE OUT jack with the

signal either before or after it is processed by the

tone/equalization circuits.

PRE (tone/EQ bypassed) POST (tone/EQ active)

7

TYPE: PR 535

PART NUMBERS: 2146800000 (120V, 60Hz) USA 2146803000 (240V, 50Hz) AUS 2146804000 (230V, 50Hz) UK

2146806000 (230V, 50Hz) EUR 2146807000 (100V, 50-60Hz) JPN

POWER REQUIREMENTS: 1800W

PREAMP INPUT IMPEDANCE: PASSIVE: 1MΩ, ACTIVE: 1MΩ

SENSITIVITY AT FULL POWER: PASSIVE: 19mV, ACTIVE: 40mV

NOMINAL LEVEL: PASSIVE: 145mV, ACTIVE: 300mV

POWER AMP INPUT IMPEDANCE: 10kΩ

SENSITIVITY: 1V R.M.S. (0 dBv)

POWER OUTPUT: 1200W R.M.S. into 2Ω @ < 0.2 % T.H.D.

TONE CONTROLS ROOM BALANCE: ±10dB, crossover frequency: 350Hz

BASS/TREBLE: BASS: ± 15dB @ 50Hz TREBLE: ± 15dB @ 10kHz

SEMI-PARAMETRIC EQ: LOW FREQ: 25Hz to 150Hz LOW LEVEL: ±15dB @ LOW FREQ setting

MID FREQ: 140Hz to 1.6 kHz MID LEVEL: ±15dB @ MID FREQ setting

HIGH FREQ: 1.4kHz to 8kHz HIGH LEVEL: ±15dB @ HIGH FREQ setting

EFFECTS LOOP IMPEDANCES: SEND: 1kΩ RETURN: 22kΩ

NOMINAL LEVEL: +4dBu (adjustable with level control)

FOOTSWITCH: One button: EQ (0055852000)

POWER CORD PART NUMBERS: 0059652000 (120V, 60Hz) USA 0059648000 (240V, 50Hz) AUS 0059649000 (230V, 50Hz) UK

0059650000 (230V, 50Hz) EUR 0059651000 (100V, 50-60Hz) JPN

RECOMMENDED SPEAKERS: 2217200000 (810 Pro) 2217100000/2217000000 (410 Pro ST/SL) 2217300000 (Bassman 212)

DIMENSIONS: HEIGHT: 3.5 in (8.9 cm) WIDTH: 19.0 in (48.3 cm) DEPTH: 15.0 in (38.1 cm)

WEIGHT: 35 lb (15.9 kg)

Product specifications are subject to change without notice.

SS

pp

ee

cc

ii

ff

ii

cc

aa

tt

ii

oo

nn

ss

FF

ee

nn

dd

ee

rr

®

88

00

PP

rr

oo

AA

mm

pp

ll

ii

ff

ii

ee

rr

wwwwww

..

ffeennddeerr..ccoomm

✧

wwwwww

..mmrrggeeaarrhheeaadd..nneett

Rack and Flight Case Mounting

The 800 Pro can be mounted in racks and flight-cases

measuring from 15.5 to 22 in (39.7 to 56.3 cm) between front

and rear rails {X} using the adjustable brackets {Y} provided.

1) Remove the 2 bolts {Z} on each side of the 800 Pro and

loosely attach the adjustable brackets {Y} as shown.

2) Lift the 800 Pro into position and provide temporary

support until all corners are attached.

3) Bolt the 800 Pro front panel tabs to the front rack rails.

4) Slide the adjustable brackets {Y} to fit the rack, then

attach with bolts through the rear rails {X} as shown.

5) Tighten all bolts securely.

Page is loading ...

A PRODUCT OF:

FENDER MUSICAL INSTRUMENTS CORP.

CORONA, CA USA

Fender

®

is a registered trademark of FMIC,

other trademarks are property of their respective owners.

REV B

Fender 800 Pro Owner's manual

Fender 800 Pro Owner's manual

in other languages

Related papers

Other documents