Toro Cable Guide Kit, RT1200 Trencher Installation guide

Brand: Toro

Model: Cable Guide Kit, RT1200 Trencher

Type: Installation guide

Toro Cable Guide Kit, RT1200 Trencher is designed to improve efficiency in cable laying operations. The kit includes a cable chute, support bracket, and mounting hardware, allowing for easy installation on the machine. The chute guides the cable from the spool to the optional vibratory plow attachment, ensuring proper cable placement and preventing tangles. By utilizing the Toro Cable Guide Kit, users can enhance their productivity and maintain a professional appearance during cable installation projects.

FormNo.3391-224RevA

CableGuideKit

RT1200Trencher

ModelNo.25498

ModelNo.25498E

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Cablechute

Supportbracket

Flanged-headbolt(10x25mm)

Locknut(10mm)

Assemblethesupportbracketthechute.

Nopartsrequired

–

Removetheheadlightcover(machines

withouttheworklightkit).

Nopartsrequired

–

Removetheheadlight(machineswith

theworklightkit).

Locknut(10mm)

Flanged-headbolt(10x25mm)

Flanged-headbolt(10x70mm)

Square-tubespacer

Rubberspacer2

Installthecablechute.

Nopartsrequired

–

Installingtheheadlightcover(machines

withouttheworklightkit).

Nopartsrequired

–

Installingtheheadlight(machineswith

theworklightkit).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3391-224*A

PreparingtheMachine

NoPartsRequired

Procedure

1.Movethemachinetoalevelsurface.

2.Settheparkingbrakeandlowertheattachmentsto

theground.

3.Stoptheengineandremovethekey.

AssemblingtheSupport

BrackettotheChute

Partsneededforthisprocedure:

Cablechute

Supportbracket

Flanged-headbolt(10x25mm)

Locknut(10mm)

Procedure

1.Aligntheholesonthesupportbrackettotheholesin

themountingangesofthecablechute(Figure1).

Note:Usetheholesateitherendofthechute.

Figure1

1.Cablechute3.Supportbracket

2.Flanged-headbolt(10x

25mm)

4.Locknut(10mm)

2.Assemblethebrackettothechutewiththe2

anged-headbolts(10x25mm)and2locknuts(10

mm)andtightenthenutsandboltshandtight(Figure

1).

RemovingtheHeadlightCover

(MachineswithouttheWork

LightKit)

NoPartsRequired

Procedure

1.Attheleftfrontheadlightcover,removethe2

anged-headboltsthatsecuretheheadlightcoverto

thefront-headlightshroudoftheROPSframe.

Figure2

1.Headlightcover

3.Clipnut(headlightshroud

ange)

2.Flanged-headbolts

2.Removethecoverfromtheshroud.

Note:Retainthecoverand2hex-headboltsfor

installationin6InstallingtheHeadlightCover

(MachineswithouttheWorkLightKit)(page5).

RemovingtheHeadlight

(MachineswiththeWorkLight

Kit)

NoPartsRequired

Procedure

1.Fromthebackoftheheadlightshroud,reachthrough

theaccessholeattheleftheadlightandreleasethe

mountinglatchthatsecurestheheadlighttotheshroud

(Figure3).

Note:Holdontothewiringwhileyoureleasethelatch

sotheheadlightdoesnotfreefallfromtheshroud.

Figure3

1.Electricalconnector

(headlight)

4.Accesshole(leftheadlight)

2.Electricalconnector

(wiringharness)

5.Frontofthemachine

3.Latch(headlightmounting)

2.Atthefrontoftheheadlightshroud,releasethelatch

fortheconnectorofthewiringharnessandremovethe

leftheadlightfromthewiringharness(Figure4).

Note:Retainthecoverandheadlightforinstallation

in7InstallingtheHeadlight(MachineswiththeWork

LightKit)(page5)

Figure4

1.Headlight(left)

3.Electricalconnector

(wiringharness)

2.Retainer(headlight)

4.Headlight

opening—outboardedge

(headlightshroud)

InstallingtheCableChute

Partsneededforthisprocedure:

Locknut(10mm)

Flanged-headbolt(10x25mm)

Flanged-headbolt(10x70mm)

Square-tubespacer

2Rubberspacer

AssemblingtheSupportBracketand

ChutetotheMachine

1.AtthelowerbackedgeoftheROPScanopy,locatethe

centerandleftofcenterslotsasshowninAofFigure5.

Figure5

1.Slots(centerandleftof

center)

6.Forward-mountingange

(cablechute)

2.Locknut(10mm)7.Square-tubespacer

3.Supportbracket8.Hole—forward-mounting

ange(cablechute)

4.Bolt(10x25mm)9.10mm(13/32inch)drillbit

5.Flanged-headbolt(10x

70mm)

2.AlignthecablechutetothecanopyoftheROPSframe

withthesupportbrackettotherearofthecanopy

(Figure5).

3.Aligntheholesinthesupportbracketforthecable

chutewiththeholesthatyouidentiedinstep1;refer

toBinFigure5.

4.Assemblethesupportbrackettothecanopywith2

bolts(10x25mm)and2locknuts(10mm)andtighten

theboltsandnutshandtight;refertoBinFigure5.

DrillingHolesintheHeadlightShroud

1.Alignthesquare-tubespacerbetweenthe

forward-mountingangecablechuteandthefront

headlightshroudasshowninCofFigure5.

2.Aligntheholesinthemountingangeofthecable

chuteandthesquare-tubespacerbyinsertingthe2

anged-headbolts(10x70mm)throughtheholes,

refertoCinFigure5

3.Remove1anged-headboltandusetheholesinthe

angeandtubeasadrillingtemplatetodrilla10mm

(13/32inch)holeintotheheadlightshroud;referto

DinFigure5.

4.Inserttheanged-headboltthroughtheholesinthe

cablechutemountingange,square-tubespacer,and

headlightshroud;refertoCinFigure5.

Note:Theboltshouldalignthecablechute,

square-tubespacer,andheadlightshroud.

5.Removetheotheranged-headboltandusetheholes

intheangeandtubeasadrillingtemplatetodrilla10

mm(13/32inch)holeintotheheadlightshroud;refer

toDinFigure5.

6.Removetheboltandsquaretubespacer.

AssemblingtheCableChutetothe

HeadlightShroud

1.Aligntheholesinthe2rubberspacersandthesquare

tubespacerwiththeholesintheheadlightshroud;

refertoAinFigure6.

Figure6

1.Locknuts(10mm)4.Flanged-headbolt(10x

70mm)

2.Forward-mountingange

(cablechute)

5.Rubberspacers

3.Square-tubespacer

6.Hardwaretorque47to57

N-m(34to42ft-lb)

2.Frominsidetheheadlightshroud,insertthe2

anged-headbolts(10x70mm)throughtheshroud,

spacers,andcablechutemountinganges,refertoA

inFigure6.

3.Securethecablechuteandspacerstothemachinewith

the2angedheadboltsand2locknuts,andtightenthe

nutshandtight;refertoAinFigure6.

4.Torquethe10mmangedheadboltsandnutsto47to

57N-m(34to42ft-lb);refertoBinFigure6.

InstallingtheHeadlightCover

(MachineswithouttheWork

LightKit)

NoPartsRequired

Procedure

1.Alignthehoseoftheheadlightcoverwiththe2clipnuts

ontheangesoftheheadlightshroud(Figure2).

2.Securethecovertotheshroudwiththe2anged-head

bolts(Figure2)thatyouremovedinstep1of3

RemovingtheHeadlightCover(Machineswithoutthe

WorkLightKit)(page2).

3.Torquetheboltsto945to1171N-cm(86to106in-lb).

InstallingtheHeadlight

(MachineswiththeWorkLight

Kit)

NoPartsRequired

Procedure

1.Atthefrontoftheheadlightshroud,connectthe

wiringharnessconnectortotheheadlight(Figure4).

2.Alignthelatchoftheheadlighttothecenterofthe

machine(Figure3).

3.Aligntheretainersoftheheadlighttotheoutboard

edgeoftheopeningintheheadlightshroud(Figure4).

4.Inserttheheadlightintotheshrouduntilthelatchof

theheadlightsnapssecurelytotheshroud(Figure4).

Operation

UsingtheCableChute

Routethecablefromthespoolthroughthecablechuteandtotheoptionalvibratoryplowattachment(Figure7).

Figure7

Notes:

Toro Cable Guide Kit, RT1200 Trencher Installation guide

Toro Cable Guide Kit, RT1200 Trencher Installation guide

Toro Cable Guide Kit, RT1200 Trencher Installation guide

Related papers

Other documents