GE 28213EE1 User manual

Category
Telephones
Type
User manual






Your telephone equipment is approved for connection to the Public Switched
Telephone Network and is in compliance with parts 15 and 68, FCC Rules and
Regulations and the Technical Requirements for Telephone Terminal Equipment
published by ACTA.
 
On the bottom of this equipment is a label indicating, among other information, the
US number and Ringer Equivalence Number (REN) for the equipment. You must, upon
request, provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your
telephone line and still have all of these devices ring when your telephone number is
called. In most (but not all) areas, the sum of the RENs of all devices connected to one
line should not exceed 5. To be certain of the number of devices you may connect to
your line as determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.

This equipment may not be used on coin service provided by the telephone
company.
Party lines are subject to state tariffs, and therefore, you may not be able to use
your own telephone equipment if you are on a party line. Check with your local
telephone company.
Notice must be given to the telephone company upon permanent
disconnection of your telephone from your line.
If your home has specially wired alarm equipment connected to the telephone
line, ensure the installation of this product does not disable your alarm
equipment. If you have questions about what will disable alarm equipment,
consult your telephone company or a qualied installer.


 
Should your equipment cause trouble on your line which may harm the telephone
network, the telephone company shall, where practicable, notify you that temporary
discontinuance of service may be required. Where prior notice is not practicable and
the circumstances warrant such action, the telephone company may temporarily
discontinue service immediately. In case of such temporary discontinuance, the
telephone company must: (1) promptly notify you of such temporary discontinuance;
() afford you the opportunity to correct the situation; and () inform you of your right to
bring a complaint to the Commission pursuant to procedures set forth in Subpart E of
Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities,
equipment, operations or procedures where such action is required in the operation
of its business and not inconsistent with FCC Rules and Regulations. If these changes
are expected to affect the use or performance of your telephone equipment, the
telephone company must give you adequate notice, in writing, to allow you to maintain
uninterrupted service.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference; and () This
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna (that is, the antenna for radio or
television that is “receiving” the interference).
Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
Connect the telecommunications equipment into an outlet on a circuit different
from that to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and
Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Ofce, Washington, D.C. 00. Please specify stock number 00-
000-005- when ordering copies.
Notice: The changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

This telephone system meets FCC standards for Hearing Aid Compatibility.

Licensed under US Patent 6,7,009.

This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 0 centimeters between the radiator and your body. This
transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter.
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines.

This telephone is compliant with the DECT 6.0 standard which
operates in the 1.9GHz to 1.9GHz frequency range. Installation of
this equipment is subject to notication and coordination with UTAM.
Any relocation of this equipment must be coordinated through and
approved by UTAM. UTAM may be contacted at 1-800-9-886.
5
EquipmEnt ApprovAl informAtion .................. 2
i
ntErfErEncE informAtion .............................. 3
H
EAring Aid compAtibility (HAc) .................. 4
l
icEnsing ...................................................... 4
fcc rf r
AdiAtion ExposurE stAtEmEnt ......... 4
i
nformAtion for dEct product ................... 4
i
ntroduction ................................................ 7
b
EforE you bEgin ........................................ 7
P
arts CheCklist ................................................... 7
t
elePhone JaCk requirements .......................... 7
i
nstAllAtion ................................................. 8
D
igital seCurity system ..................................... 8
i
mPortant installation guiDelines ................... 9
b
AsE lAyout ...............................................10
F
ront View .........................................................10
H
AndsEt lAyout ..........................................11
D
isPlay iCons .....................................................11
i
nstAlling tHE pHonE ...................................12
i
nstalling the hanDset Battery......................12
B
ase station .......................................................13
p
rogrAmming tHE tElEpHonE .......................14
s
tanDBy sCreen .................................................14
P
rogramming FunCtions ..................................14
r
oom monitor ...................................................14
a
larm CloCk ......................................................15
initial setuP .......................................................16
h
anDset name ...............................................16
D
ate anD time ................................................16
a
rea CoDe ......................................................17
t
one/Pulse .....................................................17
l
anguage ........................................................17
a
uto talk .......................................................18
r
egistration ...................................................18
D
e-registration .............................................19
g
loBal De-registration ...............................20
s
ounD setuP ......................................................20
r
inger tone....................................................20
r
inger Volume ...............................................21
k
ey tone .........................................................21

reset setting .....................................................21
V
oiCemail.........................................................22
a
ll settings ...................................................22
t
ElEpHonE opErAtion .................................. 23
V
isual inDiCators ...............................................23
B
ase .................................................................23
h
anDset ..........................................................23
Vmwi/V
isual ringer inDiCator on hanDset 23
s
PeakerPhone oPeration ..............................23
m
aking a Call ................................................24
a
nswering Calls ...........................................24
C
all timer ..........................................................24
a
uto stanDBy .....................................................25
r
inger Volume (shortCut) ...............................25
F
lash/Call waiting .........................................25
l
ast numBer reDial ..........................................26
e
xit ....................................................................26
P
age .....................................................................26
P
aging From the Base/grouP Page ...............27
m
ute ....................................................................27
r
eCeiVer Volume Control ...............................27
D
o not DisturB (D-n-D) ................................27
i
ntErcom opErAtion ....................................28
m
aking an auto interCom Call......................28
a
DVanCeD interCom Features ..........................28
r
eCeiVing an inComing Call During an
i
nterCom Call .......................................28
u
sing interCom with external telePhone
C
alls .......................................................28
t
wo-way Calling .........................................29
t
hree-way Calling.......................................29
t
ransFerring external Calls
to other hanDsets ...................................29
c
AllEr id (cid) .......................................... 30
C
all waiting Caller iD ...................................30
r
eCeiVing CiD reCorDs ....................................30
s
toring CiD reCorDs (in CiD memory) ........31
r
eViewing CiD reCorDs ...................................31
D
ialing a CiD numBer .....................................31
6
storing CiD reCorDs in internal memory ...32
D
eleting all CiD reCorDs ..............................32
p
HonEbook .................................................33
r
eView reCorDs .................................................33
a
DD reCorDs ......................................................33
i
nserting a Pause in the Dialing sequenCe
(
oF a storeD numBer) ...............................34
e
Dit reCorDs ......................................................34
F
rom PhoneBook suB-menu: .........................34
D
elete reCorDs .................................................35
D
ialing a numBer From internal memory ....35
c
HAnging tHE bAttEry .................................36
B
attery saFety PreCautions ............................36
d
isplAy mEssAgEs ........................................37
t
roublEsHooting guidE ...............................38
c
AusEs of poor rEcEption ...........................40
g
EnErAl product cArE ...............................41
A
ccEssory informAtion ...............................41
W
ArrAnty AssistAncE ..................................42
l
imitEd WArrAnty .......................................43
i
ndEx ..........................................................46

SEE M ARKIN G ON B OTTOM / BAC K OF P RODUC T
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
7













Make sure your package includes the items shown here.










For  there will be  additional handset, charge cradle, belt clip,
battery pack and cover than shown above.

To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a modular
jack, call your local phone company to nd out how to
get one installed.




8


Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.

















9

Avoid sources of noise and heat, such as motors, uorescent lighting,
microwave ovens, heating appliances and direct sunlight.
Avoid areas of excessive dust, moisture and low temperature.
Avoid other cordless telephones or personal computers.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specically
designed for wet locations.
Never touch non-insulated telephone wires or terminals, unless the telephone
line has been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
10








11



56


























 
 
 







1






1. Locate battery and battery door which are packaged together inside a plastic bag
and are separate from the handset.
. Locate the battery compartment on the back of the handset.
. Plug the battery pack cord into the jack inside the compartment.


. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
1

1. Choose an area near an electrical outlet and a telephone wall jack (RJ11C), and
place your cordless telephone on a level surface, such as a desktop or tabletop.
. Plug one end of the telephone line cord into the TEL LINE jack on the back of the
base and the other end into a modular jack.
. Plug the AC power converter into the electrical outlet and the DC connector into
the jack on the back of the base.
. Place the handset in the base cradle. The charge/in use indicator turns on,
verifying the battery is charging.
5. Allow the phone to charge for 16 hours prior to rst use. If you don’t properly
charge the phone, battery performance is compromised.




1


The handset displays the handset number and user name.

The system uses a menu structure to give you access to all of the built-in features. You
may program the following items in main menu: Phone Book, Room Monitor, Alarm
Clock, Initial Setup, Sound Setup, Reset Settings.

1. Make sure your phone is  (not in TALK mode).
. Press the
button to go to the main menu.
. Press
 (6 5) button to scroll to .
. Press the
button to enter  menu. The screen
displays ROOM MONITOR EXTENSION?.
15
5. Use the touch tone pad to enter the handset name/number to be monitored.
6. The receiving handset will turn on the microphone and the originating handset will
turn on the speakerphone to monitor sound from the receiving handset.












1. Make sure your phone is  (not in TALK mode)
. Press the
 button to go to the main menu.
. Use the
 (5 or 6) button to scroll to .
. Press
 button to enter the menu. The screen displays ON > OFF.
5. Use the
 (5 or 6) button to select  or . Press
 button to conrm.
6. If
 is selected, then the screen displays SET ALARM TIME. Use the number keys
to enter the alarm time (for example, 0:10PM) key in 010. Use the
 (5 or 6) button to select  or .
7. Press
 button to display >ONCE OR DAILY and select  or
.
8. Press the
 button to save selection. You will hear a conrmation
tone and return to main menu.
16

1. Make sure your phone is  (not in TALK mode).
. Press the
 button to go to the main menu.
. Press
 (6 5) button to scroll to .
. Press the
 button to conrm and you may program the following
items: Handset Name, Date and Time, Area Code, Tone/Pulse, Language, Auto
Talk, Registration, Deregistration.




1. Press the  (5 or 6) button to scroll to the 
sub-menu.
. Press
 button to enter the menu. The screen displays HANDSET
NAME.
. Use the touch-tone pad to enter a name (up to 15 characters). More than one
letter is stored in each of the number keys. For example, to enter Bill Smith, press
the key twice for the letter B. Press the key times for the letter I. Press the 5 key
times for the letter L. Press the 5 key times for the second letter L, and press the
1 key to insert a space between the rst and last name. Press the 7 key times for
the letter S; press the 6 key once for the letter M; press the key times for the letter I;
press the 8 key for the letter T; press the key twice for the letter H.


. Press the  button to save your name. You will hear a conrmation
tone and the handset name shows in the display.


1. Press the  (5 or 6) button to scroll to the and
sub-menu.
. Press
 button to enter the menu. Use the number keys to enter the
current date, (for example, 1 December, 007) key in 0711.
. Press
 button to conrm your selection and advance 
sub-menu.
17
. Use the number keys to enter the current hour and minute, then use the
 (5 or 6) to select  or .
5. Press the
 button to save your selection. You will hear a
conrmation tone and the current time shows in the display.


1. Press the  (5 or 6) button to scroll to the  sub-menu.
. Press
 button to enter the menu. The screen displays SET AREA
CODE - - - .
. Use the touch-tone pad to enter your -digit area code.
. Press the
 button to conrm. You will hear a conrmation tone and
the new area code shows in the display.

SET AREA CODE


1. Press the  (5 or 6) button to scroll to the 
sub-menu.
. Press
 button to enter the menu. The screen displays 4TONE
PULSE. The default setting is TONE.
. Use the
(5 or 6) to select  or .
. Press the
 button to conrm. You will hear a conrmation tone and
your selection shows in the display.


1. Press the  (5 or 6) button to scroll to the 
sub-menu.
. Press
 button to enter the menu. The screen displays 4ENGLISH
ESPANOL.
. Use the
 (5 or 6) button to scroll to the desired language.
ENGLISH is the default setting.
. Press the
 button to save your selection. You will hear a
conrmation tone and the selected language shows in the display.
18

When this function is , during an external call, you may lift the handset to answer a
call immediately without pressing any buttons. To end a call, put the handset back on
the base cradle directly.

1. Press the  (5 or 6) button to scroll to the  sub-menu.
. Press
 button to enter the menu. The screen displays > NO YES.
.
Use the  (5 or 6) button to scroll to your selection. NO is the
default setting.
. Press the  button to conrm.

Your packaged handset(s) are pre-registered and ready to use. It is not recommended
that a handset be registered again unless absolutely necessary.

1. Press the  (5 or 6) button to scroll to the 
sub-menu.
. Press the
 button to enter the menu. The screen displays YES4NO.
The default setting is NO.
. Use the
(5 or 6) button to scroll to  or .
. If you select
, press the button. The screen displays HOLD
BASE FIND FOR 5 SECONDS, THEN PRESS MENU OK KEY. (Your handset should be
held near the base during registration process.)
5. Press and hold the
 button on the base unit, the charge/in use indicator
ashes. Press the handset  button. The screen displays
REGISTERING. The handset screen displays REGISTERED. You may now rename
your handset. (Refer to Step & of Handset Name Section)



19

De-registration cancels registration. During the de-registration process, keep the
handset near the base.

1. Press the  (5 or 6) button to scroll to the 
sub-menu.
. Press the
 button to enter the menu. The screen displays YES4NO.
The default setting is NO.
. Use the
(5 or 6) button to scroll to  or .




. Select , if you do not want to de-register.
5. If you select
, press the  button and MOVE NEAR BASE displays
for seconds, then the screen displays YES NO.
6. Use the
 (5 or 6) button to scroll to  or .
7. If you select YES, press the
 button to conrm. The screen displays
DE-REGISTER.... You will hear a conrmation tone. Then the screen displays
DEREGISTERED to conrm the handset is deregistered.



0

If one or more handsets become lost, you should de-register all handsets to ensure
proper system operation.




1. Disconnect power from the base by pulling the plug out of the back of the unit.
. Press and hold the
 button and while holding the  button reconnect the
power.
. Continue to hold the
 button until the charge/in use light ashes rapidly.
. Release the
 button.
5. Press and release the
 button on the base once. All handsets are
de-registered and the screen displays HANDSET NEEDS REGISTRATION.

1. Make sure your phone is  (not in TALK mode).
. Press the
 button to go to the main menu.
. Press
 (5 or 6) button to scroll to .
. Press
 button to conrm and you may program the following
items: Ringer Tone, Ringer Volume, Key Tone.

You may choose from ve different ringer tones and ve different melodies.

1. Press the  (5 or 6) button to scroll to the 
sub-menu.
. Press
 button to enter the menu. The screen displays 4 1 OF 10.
01 is default setting.
. Use the
 (5 or 6) button to scroll to the desired setting
(1 through 10). You will hear a sample of the ringer tone/melody you select.
. Press the
 button to save your selection. You will hear a
conrmation tone and the selected ringer tone shows in the display.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

GE 28213EE1 User manual

Category
Telephones
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI