Automatic Technology Elite Installation guide

Brand: Automatic Technology

Model: Elite

Category: Garage Door Opener

Type: Installation guide

Elite®

INSTALLATION INSTRUCTIONS | OWNERS COPY

Swing Gate Opener

Technical Document

Installation Manual

v3.01

14 Dec 2011

English

Part # 13295 (Manual)

2Elite® - Swing Gate Opener Owner Installation Instructions

WARNING: It is vital for the safety of persons to follow all

instructions. Failure to comply with the installation instructions

and the safety warnings may result in serious personal injury

and/or property and remote control opener damage. Please

save these instructions for future reference.

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all

conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of

an Automatic Technology Australia Pty Ltd Elite® Swing Gate Opener. Automatic Technology Australia Pty Ltd hereby

further expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any

person as a result whether directly or indirectly from failure to install the Automatic Technology Australia Swing Gate

Opener in accordance with these installation instructions.

Owner Installation Instructions Elite® - Swing Gate Opener 3

Elite®

Swing Gate Opener

Important Safety Instructions 4

Features 6

Kit Contents 8

Drive Unit Installation 9

Installing Drive Unit Arms 11

Installing Minimum Sideroom Kit 12

Mounting Control Box 12

Five Wire Connection Single Leaf 14

Five Wire Connection Dual Leaf 15

Three Wire Connection Single Leaf 16

Three Wire Connection Dual Leaf 17

Control Board Layout 18

Menu Structure 20

Setting Travel Limits 21

Coding Transmitters 23

Standard Operating Modes 24

Control Board Adjustments 25

Menu 2 Current Trips 25

Menu 3 Auto-Close Times 26

Menu 4 Lock Times 27

Menu 5 Light Times 27

Menu 6 Motor Settings 27

Menu 7 Operating Modes 28

Diagnostic Tools 30

Menu 8.1 Test Inputs 30

Menu 8.2 Test Tx’ers 30

Menu 8.3 Display History 30

Menu 8.4 Memory Usage 30

Menu 8.5 Service Counter 31

Menu 8.6 Counters 31

Memory Tools 32

Menu 9.1 Clr Control 32

Menu 9.2 Clr Tx’ers 32

Setting Pedestrian Position 32

PE Beam installation 33

Accessories Installation 34

Battery Backup Installation 35

Troubleshooting Guide 36

Speciﬁ cations 37

Spare Parts List 38

Warranty 40

4Elite® - Swing Gate Opener Owner Installation Instructions

FOR ADDITIONAL SAFETY protection we strongly recommend the ﬁ tting of a Photo

Electric (PE) Beam. In most countries, PE Beams are mandatory on all gates ﬁ tted with

automatic openers. For a small additional outlay, Automatic Technology recommends

that Photo Electric Beams be installed with the automatic opener ensuring

additional safety and peace of mind.

DO NOT operate the gate opener unless the gate is in full view and free from objects such as

cars and children/people. Make sure that the gate has ﬁ nished moving before entering or

leaving the driveway.

DO NOT operate the gate opener when children/people are near the gate. Children

must be supervised near the gate at all times when the gate opener is in use. Serious

personal injury and/or property damage can result from failure to follow this warning.

DO NOT allow children to operate the swing gate opener. Serious personal

injury and/or property damage can result from failure to follow this warning.

Make sure that the Safety Obstruction Force system is working correctly,

and is tested every month. Test as per the Installation Instructions Manual.

Adjust if necessary and recheck. Failure to follow this rule could result

in serious personal injury and/or property damage. This test must be

repeated at regular intervals and the necessary adjustments made as

required.

DO NOT disengage the swing gate opener to manual operation

with children/people or any other objects including motor

vehicles within the gateway.

If using a key switch, keypad or any device that can operate

the swing gate opener, make sure it is out of reach of

children and that the gateway is in full view at all times.

If the power supply cord is damaged, it must be

replaced by an Automatic Technology service agent

or suitably qualiﬁ ed person.

Make sure that remote transmitters are kept out

of reach of children.

WARNING: It is vital for the safety of persons to follow all

instructions. Failure to comply with the following Safety

Instructions may result in serious personal injury and/or

property damage.

Important Safety Instructions

Owner Installation Instructions Elite® - Swing Gate Opener 5

The Elite® swing gate opener should not be immersed in water or sprayed directly by a hose or other water

carrying device.

The gate(s) must be well balanced and in good working order. Faulty gates must be repaired by a

qualiﬁ ed technician prior to opener installation.

Remove or disengage all gate locks and mechanisms prior to installation of the opener.

Connect the gate opener to a properly earthed general purpose 240V mains power outlet

installed by a qualiﬁ ed electrical contractor.

Disconnect the power cord from mains power before making any repairs or removing

covers. Only experienced service personnel should remove covers from the gate opener.

Keep hands and loose clothing clear of the gate and opener at all times.

When using Auto-Close mode, a Photo Electric Beam must be ﬁ tted correctly and

tested for operation at regular intervals. Extreme caution is recommended when

using Auto-Close mode. All safety instructions above must be followed.

In order for the gate opener to sense an object obstructing the gateway,

some force must be exerted on the object. As a result the object, gate

and/or person may suffer damage or injury.

Make sure that the gate is fully open before driving into or out of

the driveway. Make sure the gate is fully closed before leaving the

driveway.

The gate opener is not intended for use by young children or

inﬁ rm persons without adequate supervision. Children should

be supervised to ensure that they do not play with the

remote transmitters or the opener.

Frequently examine the installation and mountings for

signs of wear, damage or imbalance. DO NOT use if

repair or adjustment is needed since a fault in the

installation or an incorrectly balanced gate may

cause injury.

Important Safety Instructions

Please read this instruction manual fully before attempting

to install or use the opener. Failure to comply with the

installation instructions may result in serious injury and/or

property damage.

6Elite® - Swing Gate Opener Owner Installation Instructions

Dual Leaf Gate

A dual leaf gate can be controlled with the addition of a second drive unit. Mains

power is only required for the control box and a 5-core low voltage cable for the

drive units.

Operation

To activate the gate simply press a button on the TrioCode® transmitter,

keypad or other optional control devices. During an open or close cycle, the

gate can be stopped by pressing the button whilst it is in motion. The next

actuation will move the gate in the opposite direction.

Operator Console

The DCB-05 gate controller features a LCD display operator console which

simpliﬁ es installation, adjustments and status indication. Features include editing

transmitter storage and names, setting parameters, selecting specialised operating

modes and performing system diagnostics.

TrioCode™ Code Hopping Technology

Every time a TrioCode™ transmitter is used, a new security code is randomly generated

from over 4.29 billion possibilities. This greatly enhances the security of the system and

makes “code grabbing” a thing of the past.

These transmitters also overcome interference issues by simultaneously sending a signal over

three different frequencies. Even if two of the three signals are jammed, the system will still work.

Security Code Store

The Elite® Swing Gate Opener uses revolutionary technology to securely store up to ﬁ ve hundred and

eleven (511) transmitters in its memory with the ability to assign an 11 character name to each.

Installation

The display console on the DCB-05 gate controller “holds your hand” through the installation and setup

process. Also, during installation a handheld transmitter can be used to set gate travel limits, allowing the

installer to closely monitor the gate’s position and stop points instead of having to be within arms reach of

the console.

Gate Sync Delay

If the gate leafs overlap, a delay can be used to start one leaf moving without interfering with the other.

Features

Thank you for purchasing the Elite® Swing Gate

Opener from Automatic Technology. Designed

for residential hinged swing gates by our world

renowned team of engineers, this unit will give

years of smart, simple and secure operation.

Listed below are some of its many features.

Owner Installation Instructions Elite® - Swing Gate Opener 7

ISS (Intelligent Safety System)

Should the gate hit an obstacle or be restricted in some manner, it will automatically reverse. The

amount of force the gate should encounter before reversing is automatically adjusted by the

control system during the initialisation of the automatic opener. The gate will also stop if

restricted whilst opening. The Safety Obstruction Force should be checked at least once a

month. See installation manual for instructions.

Status Indicator

The LCD console display screen indicates through text the status of the Elite®

Swing Gate Opener. When the MAIN SCREEN is displayed, the current position

of the gate or the result of the last movement can be viewed. The display also

shows the countdown timer for Auto-Close operations. Any active input will also

be displayed along with the state of various features such as periodic service,

battery backup operation and vacation mode.

Control of Lock and Lights

The incorporated controller has dedicated outputs for operating an electric

lock, warning or courtesy lights. The timing of these outputs can be adjusted

to suit your needs. In addition, a button on a remote transmitter can be

coded to operate the light output.

Extensive Operating Modes Via Control Inputs

The DCB-05 gate controller can be conﬁ gured to operate in many

different ways via the seven (7) control and safety inputs which include

P.E, AUXILIARY OPEN, STOP, CLOSE, OSC, SWIPE and PEDESTRIAN.

Operating Modes Via Remote Controls

Operation is provided with each transmitter’s button being able to be conﬁ gured

to operate one of OSC, PEDESTRIAN, SWIPE, CLOSE, OPEN, STOP, LIGHT or

VACATION functions.

The functionality of the transmitter is further enhanced by four (4) Auto-Close modes, three

(3) PE Beam response modes and two (2) pedestrian response modes.

SmartSolar™ and Battery Backup Compatibility (optional)

The Elite® swing gate opener can be ﬁ tted with a SmartSolar™ or Battery Backup kit for operation in the event of

a power outage, or where mains power access is not available.

Pedestrian Mode

The gate can be programmed to open partially to allow pedestrian access. In a dual leaf gate, only one leaf

opens to allow pedestrians through without permitting vehicle access.

Manual Operation

The opener can be disengaged and the gate operated manually by opening the drive unit cover and

disengaging the gearbox. If power to the opener is disrupted for any reason, it can be disengaged. This will

allow you to manually open or close the gate.

8Elite® - Swing Gate Opener Owner Installation Instructions

Kit Contents

ITEM DESCRIPTION QTY

1. Drive Unit 1

2. Drive Arm Extension 1

3. Slave Arm 1

4. Gate Mounting Bracket 1

5. Plastic Washer 4

6. Shoulder Screw 2

7. Hex Head Screw 2

8. Spring Washer 2

9. Flat Washer 2

10. Control Box 1

11. Control Box Mounting Bracket 4

12. PTX-5 Keyring Transmitter 2

ﬁ g

Owner Installation Instructions Elite® - Swing Gate Opener 9

Drive Unit Installation

Mounting The Drive Unit

The Elite® swing gate opener is designed to operate

most residential swing gates. The gates must be in

good working condition and should operate by hand

relatively freely. Wind loading may affect the operation

of the opener in high wind areas. Correct obstruction

and reversing settings should be chosen for trouble

free operation.

Pre-installation Inspection

Before commencing installation, check the following:

The gate moves freely by hand for the full length of

open and close travel.

The pier or post for mounting must be of solid

construction (Brick, solid timber or steel). It must

bear most of the force applied by the drive unit.

A weatherproof 240V 10A general purpose power

point should be available within one metre of the

pier/post. If Elite® gate openers are required,

provision for underground cabling should be made

from one post to the other.

ﬁ g

Gate in open

position

Ensure sideroom clearance is adequate. Refer

to Table on page 10. If there is not enough

sideroom available, the Minimum Sideroom Kit

(Page 12) is required.

The mount distance of the Drive Unit should be

recorded. This value will be used later.

Mount

distance

Sideroom clearance

Hinge

distance

Wall/Pier

Fence

10 Elite® - Swing Gate Opener Owner Installation Instructions

ﬁ g

Drive Unit Installation

Mount

Distance Hinge Distance

0 50 100 125 150 180 200 220 mm

Sideroom clearance

90 470 470 470 470 470 470 465 460 mm

120 450 470 480 470 465 460 435 425 mm

140 470 465 470 465 460 440 420 390 mm

200 470 465 445 430 400 350 390 250 mm

The mount distance for the drive unit and the hinge

distance for the gate can be selected to optimise the

sideroom clearance. See Fig. 03.

NOTE: If the gate is already installed, measure the

hinge distance and use this table to optimise the mount

distance.

Mount drive unit using four (4) 10mm loxins or

dynabolts.

Make sure that the Drive Unit is mounted at

an appropriate height from the ground - allow

minimum 35mm clearance for drive arm extension.

NOTE: If the gateway slopes away from pier/post, make

sure an allowance is made for clearance of the drive arm

extension and slave arm to not touch the ground.

Manual Operation

Disengage drive motor by pulling manual release pin up

using the release ring. While holding the ring, rotate the

motor assembly clockwise. (Fig. 04, 05 & 06)

To re-engage, pull pin and rotate motor assembly anti-

clockwise until manual release pin clicks into place.

Engaged

position

Disengaged

position

ﬁ g

Owner Installation Instructions Elite® - Swing Gate Opener 11

Installing Drive Unit Arms

ﬁ g

Gate in closed position

Drive unit

Wall/Pier

Slave Arm

Afﬁ xing Arms And Brackets To Gate

Position gate in close position.

Attach drive arm extension to drive arm (ﬁ xed to

the drive unit) (Fig. 07), using two (2) Hex Head

screws, spring and ﬂ at washers supplied.

Attach slave arm to drive arm extension using

plastic washers and shoulder screw supplied. (See

Page 8).

Assemble Gate Mounting Bracket and Slave Arm

using shoulder screw and plastic washers. Do not

tighten yet.

Extend arms out straight and mark position where

the Gate Mounting Bracket touches the gate

(Fig. 07). From this mark, measure 10mm toward

Drive Unit and mark again. This is where the Gate

Mounting Bracket will be mounted.

Remove the Gate Mounting Bracket from the Slave

Arm and secure the Gate Mounting Bracket to the

gate at second mark.

Reassemble Slave Arm to Gate Mounting Bracket

using shoulder screw and plastic washers. Secure

ﬁ rmly.

Drive arm extension

Gate mounting bracket

12 Elite® - Swing Gate Opener Owner Installation Instructions

Mounting Control Box

Installing Minimum Sideroom Kit

Minimum Sideroom Kit

If you have limited sideroom, an optional minimum

sideroom kit reduces the gate opener’s required

sideroom to the width of the drive unit (135mm). (ATA

Order code 90182).

Fitting Minimum Sideroom Kit

Secure the extension arm from the Minimum

Sideroom Kit onto drive arm extension with supplied

M12 screws.

Drill Ø12 hole in the Drive Arm Extension (use hole

in extension arm as a guide).

Insert the other M12 screw and secure with spring

washer and nut. Check that the screws are tight

(Fig. 09)

Check that the Drive Unit is disengaged and the

gate is closed. Slide the Guide Track over the idler.

Locate Track on the gate and check travel of the

Arm. The idler should always be inside the Guide

Track in the closed and open positions (Fig. 08).

Secure the track to the gate (weld if possible).

NOTE: If a shorter arm is required, drill the drive arm

extension and extension arm where appropriate. You

should not have to cut the arms and you should still

be able to use pre-threaded hole in the drive arm

extension.

110

175

275

Mounting Control Box

CAUTION: do not use any cables which carry green/

yellow wires as this signiﬁ es earth, and do not comply

with electrical authority regulations.

The control box should be mounted near the drive

unit using four (4) 6mm screws.

Drill holes as per (Fig. 10). When locating the

control box, allow ample space around the unit for

easy access and wiring connections.

Remove cover from control box.

Determine which leaf you would like to open ﬁ rst

and close last. This gate leaf must be connected to

Motor 1 (M1) terminals on the control board.

Connect drive unit(s) to control board using 5-

core or 3-core cable.Two diodes IN4001 per drive

unit must be used with 3-core cable instalation. For

detailed electrical connection see (Fig. 14 -21).

Socket head screw M12 x 60

Idler

Nylock nut M12

Slave arm

Drive arm extension

Drill 12.5 mm

Shoulder screw

Control box mounting

Drive unit mounting

ﬁ g

Owner Installation Instructions Elite® - Swing Gate Opener 13

Note: To determine left or right hand installation,

stand inside the driveway looking out to the street.

Antenna

Mount the antenna at or above the height of the gate

or fence for optimal reception, which ever is higher.

(Fig. 11). Do not cut antenna or coaxial cable.

Cams Setup

Setting of limits for open and closed position is

performed with opener in the manual position.

WARNING: do not switch power on or engage

motor drive.

For Right Hand Side Installation:

When gate is closed, turn lower cam in a clockwise

direction (Fig. 12 & 13) until an audible click can be

heard from the lower micro-switch. Open the gate to

the required opening position and turn top cam in an

anticlockwise direction until a click can be heard from

top micro-switch.

For Left Hand Side Installation:

When gate is closed turn lower cam in a anticlockwise

direction (Fig. 12 & 13) until an audible click can be

heard from the lower micro-switch. Open the gate

to the required opening position and turn top cam in

an clockwise direction until a click can be heard from

lower micro-switch.

Mounting Control Box

Top cam

Lower cam

Motor

Microswitch

ﬁ g

Antenna

Top cam

Lower cam

14 Elite® - Swing Gate Opener Owner Installation Instructions

Five Wire Connection - Single Leaf

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

Orange

Red

White

Black

Blue

Orange

Red

White

Black

Blue

ﬁ g

Drive unit installed on right hand side of the gate

Drive unit installed on left hand side of the gate

Owner Installation Instructions Elite® - Swing Gate Opener 15

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

Orange

Red

White

Black

Blue

Orange

Red

White

Black

Blue

Orange

Red

White

Black

Blue

Orange

Red

White

Black

Blue

ﬁ g

Left hand leaf opens ﬁ rst and close last

Right hand leaf opens ﬁ rst and close last

Five Wire Connection - Dual Leaf

16 Elite® - Swing Gate Opener Owner Installation Instructions

Three Wire Connection - Single Leaf

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

White

Black

Blue

ﬁ g

White

Blue

Black

Drive unit installed on right hand side of the

gate.

One diode IN4001 is connected between

1 and 4. The second diode IN4001 is connected

between 2 and 5 on the drive unit terminal.

Drive unit installed on right hand side of the

gate .

One diode IN4001 is connected between

1 and 4. The second diode IN4001 is

connected between 2 and 5 on the drive unit

terminal.

Owner Installation Instructions Elite® - Swing Gate Opener 17

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

MOTOR 2 CONNECTOR 1

MOTOR 2 CONNECTOR 2

MOTOR 2 CLOSE LIMIT SWITCH INPUT

MOTOR 2 OPEN LIMIT SWITCH INPUT

COMMON FOR MOTOR 1 & 2 LIMIT SWITCHS

MOTOR 1 CLOSE LIMIT SWITCH INPUT

MOTOR 1 OPEN LIMIT SWITCH INPUT

MOTOR 1 CONNECTOR 1

MOTOR 1 CONNECTOR 2

24 VOLTS DC OUTPUT PLUS (+)

24 VOLTS DC OUTPUT MINUS (-)

White

Black

Blue

White

Black

Blue

White

Black

Blue

White

Black

Blue

ﬁ g

Right hand leaf opens ﬁ rst and close last.

One diode IN4001 is connected between

1 and 4. The second diode IN4001 is connected

between 2 and 5 on the drive unit terminal for

each motor.

Three Wire Connection - Dual Leaf

Left hand leaf opens ﬁ rst and close last.

One diode IN4001 is connected between

1 and 4. The second diode IN4001 is connected

between 2 and 5 on the drive unit terminal for

each motor.

18 Elite® - Swing Gate Opener Owner Installation Instructions

01 PE V+ is used to power photo electric beam.

PE In for photo electric beam for safety

PE (v-) is used to supply (-) volt to photo

electric beam.

Aux control input

OPN Programmable N/O or N/C input terminal

STP Programmable N/O or N/C input terminal

CLS N/O input terminal

OSC N/O input terminal

SWP N/O input terminal

PED N/O input terminal

COM terminal for input terminals 1 to 8

OUTPUT 2 (optional relay module coil drive)

OUTPUT 1 N/C relay contact

OUTPUT 1 COM relay contact

OUTPUT 1 N/O relay contact

MOTOR 2 terminal 1

MOTOR 2 terminal 2

MOTOR 2 close limit switch input terminal

MOTOR 2 open limit switch input terminal

COM terminal for Terminals 16,17,19 & 20.

MOTOR 1 close limit switch input terminal

MOTOR 1 open limit switch input terminal

MOTOR 1 terminal 1

MOTOR 1 terminal 2

24VDC (+) output for powering accessories

24VDC (-) output for powering accessories

Standby battery / solar charger connector

24VAC power input (from transformer)

10 amp fuse

Programmer Input

Console keypad

Console display (LCD)

Antenna connector

Control Board Layout

Owner Installation Instructions Elite® - Swing Gate Opener 19

Control Board Layout

ﬁ g

20 Elite® - Swing Gate Opener Owner Installation Instructions

Menu Structure

Menu 8

Diagnostics

Menu 9

Memory tools

Menu 10

Travel limits

Menu 1

Code

transmitter

Menu 2

Current Trips

Menu 3

Auto-close

times

Main Screen

Gate status &

information

Menu 10.1

Set gate

travel

Menu 10.2

Set pedestrian

Code

transmitter

procedure.

See page 23

Parameter list

1. M1 margin

2. M2 margin

3. Settle time

See page 25

Parameter list

1. STD Auto Close

2. PE Auto Close

3. Pedestrian Auto

4. PE Ped’n

Auto Close

See page 26

Travel limit set

up procedure.

See page 21-22

Pedestrian

position set up

procedure.

See page 32

Menu 9.1

CLR control?

Menu 9.2

CLR Tx’ers?

Memory reset operations see page 32

Menu 8.1

Test inputs

Menu 8.2

Test tx’ers

Menu 8.3

Display history

Menu 8.5

Service counter

Menu 8.6

Counters

Menu 8.4

Memory Usage

Control input

status display.

See page 30

Transmitter

testing

See page 30

Event history

display

See page 30

Periodic service

cycle counter

See page 31

Cycle and

event counter

See page 31

Memory usage

See page 30

Parameter list

1. On after

cycle time

2. On before

opn time

3. On before

cls time

See page 27

Parameter list

1. Sync delays

3.Full speed voltage

5.Slow speed voltage

6. Slow time

7.Homing/Setup

speed (voltage)

8.Stop pause

time ... etc

see page 27

Parameter list

1. PE input

response

2. Ped input

response

3. Remote code

enable

4. Activity report

ETC

See page 28

Parameter list

1. Open lock time

2. Close lock time

3. Pre-opn lock

time

4. Pre-cls lock

time.

See page 27

NOTES

1. Press PREV/NEXT buttons move to Left/Right.

2. Press OPEN/CLOSE buttons to change setting.

3. Press SET button to save changes.

4. Press EXIT to return to MENU without saving changes.

Note: System will automatically return to the main screen

after 30 secs if a menu screen is displayed and no buttons

are pressed.

Menu 5

Light times

Menu 6

Motor settings

Menu 7

Operating

Modes

Menu 4

Lock times

Page is loading ...

Automatic Technology Elite Installation guide

Brand: Automatic Technology

Model: Elite

Category: Garage Door Opener

Type: Installation guide

Download PDF

report

Automatic Technology Elite Installation guide

Automatic Technology Elite Installation guide

Related papers

Other documents