b d GDO-10 User guide

Brand: b d

Model: GDO-10

Type: User guide

GDO-10

Roll Up Door Opener

Quick Operation Guide

1.0 User Operating Controls

Button Function

01 Terminal Block

02 Programmer PG-3 Input

03 Console Previous Button

04 Liquid Crystal Display

05 Console Next Button

06 Console Open Button

07 Console Stop Button

08 Console Set Button

09 Console Close Button

2.0 Manual Door Operation

2.1 To Disengage the Opener:

1. It is recommended to do so with the door in the closed

position.

2. Pull the manual release cord towards the door, until you hear

a click.

3. Move the door manually.

2.2 To Re-Engage the Opener:

1. Check the door has not been locked by a locking device.

2. Pull the manual release cord away from the door, until you

hear a click.

3. The door will now operate from the opener.

CAUTION: When the opener is manually disengaged,

the door is no longer locked. To lock the door manually,

re-engage the opener after the door is closed.

WARNING! Please test the manual release mechanism

to ensure that the manual release is easy to operate.

No more than 20kg of force should be required to

disengage the door using the manual release cord. If

excessive force is required, contact your dealer.

3.0 Coding a Remote Control

3.1 Storing the Remote Control Code:

The GDO-10 ToroTM can store up to 511 transmitters in its

memory.

3.2 Battery Replacement:

Battery Type: 1 x CR2032.

1. To test the battery is working, press and hold a remote

button. Check Light Status table to determine if battery

needs replacing.

2. Use finger nails to separate the

remote casing to expose circuit

board.

Light Status Battery Status

Solid OK

Flashing Replace

No light Replace

3. Use a non-metallic object to push the battery down

through the side opening to remove the battery.

P/N# 100555

DOC# 160475_00

TO DISENGAGE:

PULL HANDLE DOWN

& RELEASE

TO RE-ENGAGE:

REPEAT ACTION

PULL

HANDLE

IN THE EVENT THE DOOR BECOMES OBSTRUCTED

DETACH DOOR FROM OPENER AS FOLLOWS:

To r

WARNING! The battery is hazardous and must

be kept out of reach of children.The battery

can cause severe or fatal injuries within 2 hours

or less if swallowed or placed inside any part

of the body.If you suspect the battery has been

swallowed or placed inside any part of the body,

SEEK IMMEDIATE medical attention.

Button 1

To access the NEXT and SET button, unscrew

the screws at the bottom of the logic console

cover and remove cover.

tip

1. Press NEXT on the console to navigate to Menu 1.

2. Press SET to enter the code set procedure.

3. Controller will prompt to press one of the transmitter’s

buttons.

4. Press button 1 to

operate the door

opener and release.

5. Press the same button

again as prompted by

the display and release.

6. Press the SET button to

store the transmitter.

Scan: for installation manual

For product assistance,

general enquiry or more information,

please visit:

ata-aust.com.au

or call 1300 133 944.

4.0 Troubleshooting 5.0 Caring for your Opener

Preventative servicing of your garage door and opener,

is important. Your garage door is made up of numerous

moving parts designed to lift and lower your door safely

and efficiently.

Ongoing preventative servicing ensures that your door

continues to function within factory specifications, greatly

reduces the risk of failure and repair bills down the track and

ensures you maintain your Warranty.

Refer to your Owners Opener Handbook for your service

schedule.

6.0 Need a Service Call?

If the opener needs a service please call the dealer who

installed the garage door opener (their contact details are

usually on a sticker on the back of your garage door).

Refer to the installation manual for

monthly testing procedures in Section 12

to ensure garage door is fit for use.

tip

Symptom Possible cause Remedy

Door will not operate Mains power not switched on.

Door is obstructed.

Door is locked or motor jammed.

Door tracks/hardware damaged.

The stop function is activated

The opener is in “Vacation Mode”

Switch on mains power.

Remove obstruction.

Unlock door or remove jam.

Door requires service/repair by qualified technician

Deactivate the stop switch/timer

Turn off “Vacation Mode”

Door starts to close but

automatically reverses to open

position

Possible obstruction in the doorway. Remove obstruction.

Door operates from wall control

unit (OPEN/CLOSE) button but

not from transmitter

Transmitter code not stored in memory. Code transmitter in to openers memory.

Flat battery in transmitter Replace battery

Door does not close with

transmitter

Safety Close Mode is on.

Safety Beam not working properly.

Turn the Safety Close Mode off

Make sure Safety Beam are operational.

Door will not close fully. Door limit positions need to be reset.

Door obstructed and reverses.

Reset limits positions.

Clear obstruction or adjust force margin

Door will not open fully. Door limit positions need to be reset.

Door obstructed.

Reset limits positions.

Clear obstruction or adjust force margin

Auto-Close not working Safety Beam not installed.

Safety Beam or wiring faulty.

Safety Beam not aligned correctly.

Safety Beam is obstructed.

Door obstructed when closing.

Auto-Close time not set.

Auto-Close mode not set

Install Safety Beam.

Repair Safety Beam or replace wiring.

Re-align optics.

Remove obstruction from path of Safety Beams.

Remove obstruction.

Set Auto-Close times.

Set Auto-Close mode.

b d GDO-10 User guide

Brand: b d

Model: GDO-10

Type: User guide

Download PDF

report

b d GDO-10 User guide

b d GDO-10 User guide

Related papers

Other documents