TECHNIBEL 397718909 User manual

08180012-2 03/2003

TECHNICAL DATA & SERVICE MANUAL

MODELS WITH R407C

SMDV

PAGE

UNIT SPECIFICATIONS

3

INDOOR UNIT COMPONENTS SPECIFICATION

4-5

OUTDOOR UNIT COMPONENTS SPECIFICATION

6

UNIT DIMENSIONS 6

ROOM TEMPERATURE CONTROL

7

HEAT EXCHANGER FROSTING PREVENTION

7

PERFORMANCE CHART

8

THE UNIT DOES NOT WORK 9

ELECTRICAL CIRCUIT INTERRUPTED AFTER "ON" IS PRESSED

9

ELECTRIC CIRCUIT INTERRUPTED 3 MINUTES

AFTER "ON" IS PRESSED

10

FAN MOTOR DOES NOT WORK WHILE "ON" BUTTON

IS PRESSED.

10

FAN MOTOR WORKS AT ONE SPEED ONLY (FMI) 11

POOR COOLING 11

FAN MOTOR WORKS NORMALLY BUT THE

COMPRESSOR DOES NOT OPERATE (FMI)

12

OUTDOOR UNIT FAN (FMO) DOES NOT OPERATE

12

THE FLASHING LED IS ON, AND THE UNIT NOT OPERATE

13

COMPRESSOR DOES NOT WORK BUT FAN MOTOR OPERATE NORMALLY

13

ELECTRIC WIRING DIAGRAM

14/15

1;ADDED NEW ELECTRIC WIRING DIAGRAM FOR MODELS SMDV143C5

REVISIONS

CONTENTS

2

TECHNICAL DATA

UNIT SPECIFICATIONS

MODEL

SMDV9XC5 SMDV11XC5 SMDV14XC5

PERFORMANCES (NOTE 1)

COOLING

Power source

230V

Capacity

BTU/h

8500

9890

12600

W

2480

2900

3700

Air flow rate (evaporator)

High/low

m³/h

420/320

460/370

Air flow rate (condenser)

High/low

m³/h

1200

1350

Moisture removal l/h 0,8 11,6

ELECTRICAL RATINGS

Voltage rating

230V ~ 50Hz

Available voltage range

V

198÷264

Running amperes

A

4,1

4,6

6,1

Power input

W

930

1030

1300

Coefficient of performance

W/W

2,8

3

Compressor locked rotor amperes A20 23 35

FEATURES

Controls/Temperature controls

Control unit

Fan speed

Compressor

Refrigerant/standard charge at shipment

R407C g

750

870

1040

Refrigerant control

Noise level Lp (NOTE 3) INT.high/low dB(A) 44/40 44/40 47/45

EXTERNAL

dB(A)

48

41

Flexible tube lenght

m

2,5 m

DIMENSIONS & WEIGHT

Internal unit

Height

mm

800

Width mm 470

Depth mm 310

External unit

Height

mm

435

490

Width

mm

440

525

Depth

mm

230

250

Net weight

Internal unit

Kg

39

40

41

External unit Kg 8,5 9,5 13

Data can be changed without notice

NOTE 1: Rating conditions (ISO 5151):

Internal temperature: 27°C D.B. , 19°C W.B.

External temperature: 32°C D.B. , 24°C W.B.

NOTE 2: Operating limits: MINIMUM MAXIMUM

Internal temperature: 15°C D.B.,12°C W.B. 32°C D.B.,23°C W.B.

External temperature: 15°C D.B. 46°C D.B.

NOTE 3: Refering data :

Internal unit: room size 100m3 ; reverberation time 0,5sec.; distance 2m.

External unit: hemispheric radiance; distance 4m.

switches on the unit

two

Rotary (hermetic)

Capillary tube

Electronic/ I.C. thermostat

3

TECHNICAL DATA

INDOOR UNIT COMPONENTS SPECIFICATION

MODEL

SMDV9XC5 SMDV11XC5 SMDV14XC5

CONTROLLER P.C.B.

(CE)

RY1 SPLIT / RY1.1 SPLIT

Controls

Thermostat

Setting

°C

15 ± 1,5°C ÷ 31 ± 2°C

Differential

°C

0,9 ± 0,2°C

Starting delay time

3min. ± 10sec.

Function selection and indicator lamps

Frosting prevention

OPEN

°C

1 ± 1°C

CLOSE

°C

6 ± 1°C

Transformer

Power

1,5VA

Primary 220V

Secondaty 10,5V

Primary resistance

20°C

2754

Ω

±10%

Secondary resistance

20°C

17,1

Ω

±10%

COIL TEMPERATURE SENSOR

(TH1)

NTC

Resistance kΩ -20°C 5846±5% ; 20°C 604±5%

-10°C 3159±5% ; 30°C 368±5%

0°C 1766±5% ; 40°C 230±5%

10°C 1018±5% ; 50°C 147±5%

AIR TEMPERATURE SENSOR

(TH2)

NTC

Resistance

k

Ω

10°C 1018±5% ; 30°C 368±5%

15°C 781±5% ; 35°C 290±5%

20°C 604±5% ; 40°C 230±5%

25°C 470±5% ; 50°C 147±5%

FAN & FAN MOTOR (FMI) M01582

Cross - Flow

Dimensions

mm

Ø 125 x 295

Power supply

230V~50Hz

N° of poles

4

High/low speed

rpm

1150/870

1180/950

1260/1040

Nominal input (230V) W36

Coil resistance (20°C)

Ω

GRY-WHT : 392 ± 5%

WHT-YEL : 213 ± 5%

YEL-PNK : 66 ± 5%

GRY-BRN : 163 ± 5%

Safety device

Internal thermostat

Setting:

open

150±10

close

Automatic

RUN CAPACITOR

(C1)

INDOOR FAN MOTOR

Capacity

µF

0,6

1

Tension

V~

440

CONDENSER PUMP

(PC)

PC 95643

Power supply

230V~50Hz

Nominal input (230V)

W

12±10%

Coil resistance (20°C)

Ω

122±10%

PUMP RELAY

(RP)

-

FINDER 60.62

Coil power

-

230V~50Hz

Coil resistance (20°C)

k

Ω

-

7,250±10%

Contact rating

-

10A - 250V

FLOAT MICROSWITCH

CROUZET F83161.3

Contact rating

10(4)A - 250VAC

Float

up

Open

Down

Close

Electronic microprocessor

COOLING / FAN

HIGH/LOW speed

ALARM lamp

ON / OFF

4

TECHNICAL DATA

MODELS

POWER RELAY (COMPRESSOR)

FINDER OMRON FINDER OMRON OMRON OMRON

65.31 G4F 65.31 G4F G7L G4F

P.C.B.

Type

RY1 RY1.1 RY1 RY1.1 RY1 RY1.1

Coil tension

230V~50Hz 12Vdc 230V~50Hz 12Vdc 230V~50Hz 12Vdc

Coil resistance (20°C)

Ω

7.250±10% 158±10% 7.250±10% 158±10% 21.000±15% 158±10%

Contact rating 30A-250V 20A-250V 30A-250V 20A-250V 25A-250V 20A-250V

COMPRESSOR

(CM)

Model

Nominal input (230V)

W

Compressor oil

cc

Coil resistance (20°C)

C-R

C - R

Ω

C-S

Ω

SAFETY DEVICE (OLR)

Operanting temperature Open

Close

Operanting amperes

Open

(Room temperature 25°C)

Operanting temperature (OLR 1)

Open

Close

Operanting temperature (OLR 2)

Open

Close

Operanting temperature Open

(Room temperature 25°C)

RUN CAPACITOR (C3)

Capacity µF

Power supply

V~

RUN CAPACITOR

(C4)

COMPRESSOR

Capacity

µF

Power supply

V~

POWER RELAY (RA) COMPRESSOR

Type

Coil tension

V~

Coil resistance (20°C)

k

Ω

Contacts rating

Operating voltage

CURRENT LIMITER

(LC)

Type

Coil resistance (20°C)

Ω

Induttance ( a 19A~50Hz)

mH

HEAT EXCHANGER

Coils

Rows

Fin pitch mm

Face area m²

SMDV11XC5

500

3,01±7%

550

1,92÷1,84±7%

5,28÷7,1±7%

MRA990003-9201 MST20ALU-9201

3,31±7%

7,82±7%7,35±7%

500

in 6÷16 sec.

135±5°C

69±11°C

19A

in 6÷16 sec.

140±5°C

22,5A

in 6÷16 sec.

CS-7C115

115±4°C

95±10°C

MST56ALU

80235245B

1290

COMPRESSOR

150±5°C

69±11°C

830 950

80225245B 80228245B

22,5

450

20

450

233

60÷120V~

R143C

690±5%

14

Alluminium fin / Copper tube

EVAPORATOR COIL

1,8

0,118

300V~50Hz

330

AMVL300C

25

450

69±11°C

16A

SMDV9XC5

SMDV14XC5

IF EQUIPED

13,150±2%

20A

185÷217V~

56

5

TECHNICAL DATA

OUTDOOR UNIT COMPONENTS SPECIFICATION

MODELS

SMDV9XC5 SMDV11XC5 SMDV14XC5

FAN & FAN MOTOR

(FMO)

M01515

M01525

proppeler fan

Dimensions

mm

Ø 280

Ø 340

Power supply

n° of poles

4

6

Rpm

1230

870

Nominal input (230V) W61 61 75

Coil resistance (20°C)

Ω

BLU - BRN

263±7%

230±7%

Ω

BLU - BLK

285±7%

243±7%

safety device

Setting:

OPEN

°C

150±10

CLOSE

FAN ALTERNATIVE MOTOR (FMO) 40101243-L 40101243-L -

Nominal input (230V)

W

70

-

Coil resistance (20°C)

Ω

BLU - BRN

-

203±7%

-

ΩBLU - BLK BLU - BLK -

201±7%

-

safety device Thermostat Thermostat -

Setting: OPEN °C 150±10 150±10 -

CLOSE

Automatic

-

RUN CAPACITOR

(C2)

Capacity µF 2 2 2,5

Power supply

V~

450

HEAT EXCHANGER

Coils

Rows

1

2

Fin pitch mm

1,4

1,6

Face area m²

0,23

0,3

UNIT DIMENSIONS (mm)

A

G

F

C

D

B

SMDV97C5

SMDV117C5

SMDV147C5

A

800

B

470

C

310

D

440

525

F

435

490

G

230

250

Alluminium / Copper tube

EXTERNAL FAN MOTOR

Automatic

Internal thermostat

230V~50Hz

CONDENSER COIL

6

TECHNICAL DATA

ROOM TEMPERATURE CONTROL

Room temperature control is obtained by cycling the compressor ON and OFF by means of room

temperature sensor TH

minimum

2 minutes

ON/OFF SWITCH

COMPRESSOR

SWITCH

COMPRESSOR

SET

TEMPERATURE +1°C

SET

TEMPERATURE

FAN SET SPEED

NOTES:

1. If the compressor is turned off, the control circuit sets an automatic minimum 3 minutes delay to protect the

compressor from stalling out when trying to start against the high side refrigerant pressure.

2. If the room temperature is 1°C above the set temperature, the compressor starts working if this has been

OFF for at least 3 minutes.

3. If the room temperature is the same or under the set temperature the compressor stops working.

HEAT EXCHANGER FROSTING PREVENTION

The electronic control stops automatically the compressor each time the coil sensor TH reaches a

temperature of 1°C for 8 ÷ 10 minutes long, the compressor starts again automatically when the

temperature of heat exchanger reaches 8°C. The fan goes on working at the set speed.

minimum 10 minimum

minutes 3 minutes

ON/OFF SWITCH

COMPRESSOR

SWITCH

COMPRESSOR

HEAT EXCHANGER

TEMP.= 8 °C

HEAT EXCHANGER

TEMP.= 1 °C

FAN

SET SPEED

7

TECHNICAL DATA

PERFORMANCE CHART

OPERATING CHARACTERISTICS WITH RELATIVE HUMIDITY AROUND 50%

SMDV117C5

3

3,5

4

4,5

5

5,5

20 25 30 35 40 45 50

EXTERNAL TEMPERATURE (°C)

OPERATING CURRENT (A)

21 °C

27 °C

32 °C

SMDV97C5

3

3,2

3,4

3,6

3,8

4

4,2

4,4

4,6

4,8

5

20 25 30 35 40 45 50

EXTERNAL TEMPERATURE (°C)

OPERANTING CURRENT (A)

21 °C

27 °C

32 °C

SMDV147C5

4

4,5

5

5,5

6

6,5

7

20 25 30 35 40 45 50

EXTERNAL TEMPERATURE (°C)

OPERATING CURRENT

(A)

32 °C

27 °C

21 °C

8

SERVICE MANUAL

THE UNIT DOES NOT WORK

Check the voltage. Are NO Check the unit YES Check the electrical

there 198 ÷ 264 volts ? electrical cable supply line

YES

(IF INSTALLED) If it is impossible to

Check if programmer NO close the contact,

contact is closed (black - replace the

brown cables). programmer.

YES

Check if the supplied NO Check if tank micro -

voltage on switch contacts are

the electric control (CE) closed.

(1 - 2 MS contacts)

YES

NO

Replace the electronic Check if the pilot NO Is the flickering alarm

control (CE) lamp is burnt. lamp on the control

Eventually replace panel not visible ?

it.

ELECTRIC CIRCUIT INTERRUPTED WHEN "ON" BUTTON IS PRESSED

Check the unit hardness NO Insulate the short

Is it insulated ? circuit cable

YES

Check if the fan motor is NO Replace the fan motor

working (FMI) (FMI)

YES

Check if the fan motor is NO Replace the fan motor

working (FMO) (FMO)

YES

Check the electronic NO Replace the electronic

control (CE) control (CE)

YES

Check the leds printed NO Replace the leds

circuit. printed circuit.

NO

(IF INSTALLED) Replace the

Check the motor YES

programmer (P). Is it

programmer (P)

short circuited?

9

SERVICE MANUAL

ELECTRICAL CIRCUIT INTERRUPTED 3 MINUTES AFTER "ON" BUTTON IS

PRESSED.

COOLING

OPERATION

Check if compressor relay NO

Rebuild the

connections are connections.

insulated.

YES

Check if compressor relay YES

Replace the

works. Is it in short

compressor relay

circuit ? (PR)

NO

Check if compressor

winding are short

circuited.

YES

Replace the NO (FMO) Check if

compressor(CM) outdoor fan motor

works

FAN MOTOR (FMI)DOES NOT WORK WHILE "ON" BUTTON IS PRESSED

Disconnect the unit from line. Check if the fan motor is well

fitted and if the blades can rotate

YES NO NO

Check hardness and Fit the fan motor Remove obstruction

various continuities properly or replace or replace fan motor

YES it assembly

Check the capacitor NO Replace the capacitor

capacity (C)

YES

Check the fan motor INTERRUPTED Replace the fan motor

windings (FMI). assembly

YES

Replace the electronic

control (CE)

10

SERVICE MANUAL

FAN WORKS AT ONE SPEED ONLY(FMI)

Check electrical conec- NO Fit electrical connec -

tions. Is there continuity ? tions properly

YES

Check power supply NO Replace the electronic

on electronic control (CE)

control contacts (CE)

YES

Check fan motor winding

values (FMI))

YES

Replace fan motor (FMI)

POOR COOLING

Is the unit cooling capacity NO Suggest a more power-

suitable for the room ful unit

thermal loads ?

YES

Are both air filters and heat NO Clean filters and / or

exchanger cleaned ? heat exchanger

YES

Check if difference bet- YES The unit works properly

ween room air

temperature and outlet air

delivered is up to 10 °C

NO

Low

NO

gas charge

Proceed with

normal operations

foreseen for the

above points

11

SERVICE MANUAL

FAN MOTOR WORKS NORMALLY BUT THE COMPRESSOR DOES NOT OPERATE(FMI)

Check hardness

and continuity. Is the

relay compressor

coil (PR white cable)

power supplied ? YES

Replace the relay NO Check if relay YES Is the thermostat NO Adjust thermostat

(PR) contects are closed in the right posi - position

tion ?

YES YES

Replace klixon (ORL) YES Check compressor Is room tempera - NO The unit cannot

klixon contacts(ORL) ture over 15 °C ? operate below

Are they open ?

15 °C

NO YES

Replace the NO Check the capaci - Check the sensor NO Replace the

capacitor (C) tor capacity (C) continuity (TH) sensor (TH)

on electronic

control (CE)

YES terminal blocks

YES

Replace the NO Check the com - Check electronic

compressor pressor winding control (CE)

continuity

OUTDOOR FAN(FMO) DOES NOT OPERATE.

Have 3 minutes time delay Wait for about 3 minutes

already elapsed since "on"

NO

operation?

YES

Disconnect the unit from line Remove causes stopping

and manually rotate the

NO

rotation.

propeller

YES

Check electrical connections Replace outdoor fan motor

and winding continuity on

NO

(FMO)

outdoor fan(FMO).

YES

Is the voltage in coil relay (RC)

YES

Is the relay contact closed

NO

Replace relay(RC)

(RC) ?

NO

YES

Check electronic control (CE)

Check capacitor capacity.

NO

Replace capacitor

(FMO)

NO

Replace electronic control (CE)

12

SERVICE MANUAL

THE FLASHING LED IS ON, AND THE UNIT DOES NOT OPERATE

Check electrical connections

and cable continuity.

YES

Check safety micro floating (MS)

NO

Replace safety micro floating (MS)

YES

Check condensate pump motor

NO

Replace condensate pump motor

(PC)

YES

Check pump relay (RP)

NO

Replace pump relay (RP)

YES

Replace safety relay (RS)

COMPRESSOR DOES NOT WORK BUT FAN MOTOR OPERATES NORMALLY.

Check hardness and continuities. Have 3 minutes time delay Wait for about 3 minutes

Is relay compressor coil power NO already elapsed since"on" NO

supplied (RC) ?

operation ?.

YES YES

Replace

NO

Check if relay

Is the thermostat properly

NO

Properly adjust

relay(RC) contact is closed set? thermostat position.

YES

Replace

NO

Check if

Is it properly fitted? It could

NO

Fit it properly,

klixon(K)

compressor

be fitted inversely.

klixon is open

YES

Replace

NO

Check

Is the rom temperature over

NO

Below 15 °C the unit

compressor.

compressor

15 °C

cannot work.

capacitor

capacitor(C)

YES

Replace

NO

Check

Check sensor continuity of

NO

Replace sensor (TH)

compressor.

compressor

(TH) CE terminal blocks.

winding continuity

YES

Check electronic control.(CE)

13

TECHNICAL DATA

ELECTRICAL WIRING DIAGRAM FOR MODELS WITH POWER RELAY 220V AND PCB RY1

SMDV147C5

ELECTRICAL WIRING DIAGRAM FOR MODELS WITH POWER RELAY 12V AND PCB RY1.1

SMDV147C5

Legend of colors

C/CM

COMPRESSOR

S/THx

SENSOR

N/BLK

BLACK

CVx/Cx

CAPACITOR

F/TF

THERMOFUSE

B/BLU

BLUE

RE

ELECTRIC HEATER

TS

SAFETY THERMOSTAT

M/BRN

BROWN

MVx/FMx

FAN MOTOR

P

PROGRAMMER

G/V-GRN/YEL

GREEN/YELLOW

K/ORL

OVERLOAD PROTECTOR

RP

PUMP RELAY

A/ORG

ORANGE

CE

ELECTRONIC CONTROL

IM

MOTOR IMPEDANCE

R/RED

RED

PR

COMPRESSOR RELAY

RS

SAFETY RELAY PUMP

W/WHT

WHITE

MP

PUMP FLOAT MICROSWITCH

PC

PUMP

YEL

YELLOW

MS

SAFETY FLOAT MICROSWITCH

GRN

GREEN

RR

ELECTRIC HEATER RELAY

PNK

PINK

G/GRY

GREY

SMDV97C5-SMDV117C5

SMDV9XC5-SMDV11XC5

14

TECHNICAL DATA

ELECTRICAL WIRING DIAGRAM FOR MODELS WITH POWER RELAY 12V AND PCB RY1.1

Legend of colors

C/CM

COMPRESSOR

S/THx

SENSOR

N/BLK

BLACK

CVx/Cx

CAPACITOR

F/TF

THERMOFUSE

B/BLU

BLUE

RE

ELECTRIC HEATER

TS

SAFETY THERMOSTAT

M/BRN

BROWN

MVx/FMx

FAN MOTOR

P

PROGRAMMER

G/V-GRN/YEL

GREEN/YELLOW

K/ORL

OVERLOAD PROTECTOR

RP

PUMP RELAY

A/ORG

ORANGE

CE

ELECTRONIC CONTROL

IM

MOTOR IMPEDANCE

R/RED

RED

PR

COMPRESSOR RELAY

RS

SAFETY RELAY PUMP

W/WHT

WHITE

MP

PUMP FLOAT MICROSWITCH

PC

PUMP

YEL

YELLOW

MS

SAFETY FLOAT MICROSWITCH

GRN

GREEN

RR

ELECTRIC HEATER RELAY

PNK

PINK

G/GRY

GREY

SMDV143C5

15

TECHNIBEL 397718909 User manual

This manual is also suitable for

TECHNIBEL 397718909 User manual

Related papers

Other documents