Fortin EVO-ALL User manual

EVO-ALL
Fortin
Brand
Fortin
Model
EVO-ALL
Type
User manual

Fortin EVO-ALL is a versatile remote starter and security system interface module that allows you to integrate a variety of remote starters and security systems into your vehicle. It features bypass modules for most popular vehicle makes and models, eliminating the need for additional bypass modules. With the EVO-ALL, you can start your vehicle, lock and unlock your doors, and activate your alarm system, all from the convenience of your remote control.

Fortin EVO-ALL is a versatile remote starter and security system interface module that allows you to integrate a variety of remote starters and security systems into your vehicle. It features bypass modules for most popular vehicle makes and models, eliminating the need for additional bypass modules. With the EVO-ALL, you can start your vehicle, lock and unlock your doors, and activate your alarm system, all from the convenience of your remote control.

ALL
REVO GUIDE # 88761 - REV.: 20190715
Parts required (not included): 1x FLASH-LINK UPDATER
1x Microsoft Windows Computer with Internet connection
1Plug in the FLASH-LINK UPDATER into the computer’s USB port with the
provided USB cable.
2Run Flash Link Manager Software.
3Plug in the EVO-ALL into the FLASH-LINK UPDATER with provided
DATALINK cable.
PAGE 2 / 4 REVO
4
A. Click on BYPASS tab.
B. Activate Supported RF Kits to ON
C. Activate Option H3 – CrimeStopper
D. Click SAVE OPTIONS
E. Wait for the Options Saved message to appear in the top right corner.
5Disconnect the EVO-ALL.
PAGE 3 / 4 REVO
6
Red12V Battery(+)
BlackGround | Masse(-)
FUSE
FUSIBLE
12V
Battery (+)
Ground
Masse
ALL
RFA2A
WITH T-HARNESS - AVEC T-HARNAIS
BLUE FEMALE
CONNECTOR
CONNECTEUR
FEMELLE BLEU
BLACK FEMALE
CONNECTOR
CONNECTEUR
FEMELLE NOIR
NOT CONNECTED
---------------------
NON BRANCHÉ
ALL
RFA2A
Red
Black
ISOLATE
NOT CONNECTED
---------------------
ISOLEZ
NON BRANCHÉ
BLUE FEMALE
CONNECTOR
CONNECTEUR
FEMELLE BLEU
BLACK FEMALE
CONNECTOR
CONNECTEUR
FEMELLE NOIR
BLACK 4-PIN DATA-LINK
T-HARNESS* CONNECTOR
CONNECTEUR 4-PIN
DATA-LINK DU T-HARNAIS*
BLACK 4-PIN
CONNECTOR
CONNECTEUR
4-PIN NOIR
BLACK 4-PIN
CONNECTOR
CONNECTEUR
4-PIN NOIR
T-HARNESS*
AVAILABLE *Optional -
Sold separately depending
on the vehicle.
---------------------
HARNAIS EN T*
DISPONIBLE: *Optionnel
- vendu séparement
selon le véhicule.
REVO
ANTENNA CABLE
CÂBLE ENTENNE
REVO
ANTENNA
ANTENNE
REVO
ANTENNA
ANTENNE
REVO
ANTENNA CABLE
CÂBLE ENTENNE
Connect both modules together as shown.
PAGE 4 / 4 REVO
TO PROGRAM REMOTES ON THE UNITS
2
3
LOCK
ACCON
PUSH
START
IGN
5
6
LOCK
ACCON
PUSH
START
OFF
4
1 1
2
3
4
5
6
PRESS
TURN
ON/RUN
LOCK
TURN
OFF
IGNITION OFF IGNITION ON
x1
x1
HOLD
HOLD
ON BLUE
BLEU
ON RED
ROUGE
RELEASE
5 SEC.
PRESS & HOLD 5 SEC.
RELEASE
HOLD
5 sec. ON
ON
ON
ON
ON
ON
ON
PRESS
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
START
3 SEC.
OR
OU
Turn the Ignition to the
ON/RUN position.
Turn the Ignition to the OFF
position.
The remotes are now
programmed.
Use the remote of the remote
starter or security system to test
all of the supported features to
ensure proper programming.
The remotes is now
programmed.
Use the remote of the remote
starter or security system to test
all of the supported features to
ensure proper programming.
Press and hold
Insert
the
programming button:
the 4-Pin (Data-Link)
connector.
The Blue, Red, Yellow and
Blue & Red LED’s will
alternatively illuminate.
Release the programming
button when the LED’s are
RED and BLUE.
If the LED are not solid BLUE
and RED the 4-
Pin connector (Data-Link)
and go back to step 1.
disconnect
Press
Release the programming
button.
hold theand
programming button
5 seconds.
The RED and BLUE LED’s
will turn OFF.
The RED and BLUE LED’s
will turn ON.
The YELLOW LED will turn
ON.
The BLUE and RED LED’s
will flash once to confirm
remote is coded.
Press the LOCK button on
remotes you wish to
program. (You can also
press the "Start" button, but
you will have to hold it for 3
seconds.)
All remotes must be program
at the same time.
Turn the
Ignition OFF.
Turn the
Ignition OFF.
Turn the
Ignition ON.
Press and
release the
brake pedal
four times.
On each
Transmitter
press and
release the
LOCK button
Turn the
Ignition ON.
WITH IGNITION SWITCHWITH EVO-ALL MODULE
PAGE 5 / 4 REVO
WARNING
NOTICE The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product,
including either damage to the vehicle itself or to the remote-starter module. This module must be installed by a certied technician
including all of the supplied safety devices. Please note that this guide has been written for trained professional technicians, a certain
level of skills and knowledge is therefore assumed.
Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this mo-
dule, except for the replacement of this module in case of manufacturing defects. This module must be install by qualied technician.
This instruction guide may change without notice.
To download the installation guide, user guide, or the latest quick installation guide, visit: www.fortin.ca
Technical support: TEL: 514-255-4357 / 1-877-336-7797
Copyright © 2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED MADE IN CANADA REV.:20190517
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Fortin EVO-ALL User manual

EVO-ALL
Fortin
Brand
Fortin
Model
EVO-ALL
Type
User manual

Fortin EVO-ALL is a versatile remote starter and security system interface module that allows you to integrate a variety of remote starters and security systems into your vehicle. It features bypass modules for most popular vehicle makes and models, eliminating the need for additional bypass modules. With the EVO-ALL, you can start your vehicle, lock and unlock your doors, and activate your alarm system, all from the convenience of your remote control.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents