CAME ZLX24MA, ZLX24MR Installation guide

Control panel for 24 V gearmotors

ZLX24MA ZLX24MR

INSTALLATION MANUAL

FA01885-EN

EN English

Page 2 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

GENERAL PRECAUTIONS FOR INSTALLERS

Important safety instructions.

Please follow all of these instructions. Improper installation may cause

serious bodily harm.

Before continuing, please also read the general precautions for users.

Only use this product for its intended purpose. Any other use is hazardous. • The

manufacturer cannot be held liable for any damage caused by improper, unreasonable

or erroneous use. • This product has been designed to be assembled to partly

completed machinery and/or equipment so as to build machinery as regulated by

the Machinery Directive 2006/42/EC. • The ﬁ nal installation must comply with the

Machinery Directive (2006/42/EC) and the European reference standards in force. •

The manufacturer declines any liability for using non-original products, which would

also void the warranty. • All operations indicated in this manual must be carried

out exclusively by skilled and qualiﬁ ed personnel and in full compliance with the

regulations in force. • The device must be installed, wired, connected and tested

according to good professional practice, in compliance with the standards and laws

in force. • Make sure the mains power supply is disconnected during all installation

procedures. • All the components (e.g. actuators, photocells and sensitive edges)

needed for the ﬁ nal installation to comply with the Machinery Directive (2006/42/

EC) and with the reference harmonised technical standards are speciﬁ ed in the

general CAME product catalogue or on the website www.came.com. • Check that

the temperature ranges given are suitable for the installation site. • Make sure that

no direct jets of water can wet the product at the installation site (sprinklers, water

cleaners, etc.). • Make sure you have set up a suitable dual-pole cut-o device along

the power supply that is compliant with the installation rules. It should completely

cut o the power supply according to category III surcharge conditions. • Demarcate

the entire site properly to prevent unauthorised personnel from entering, especially

minors. • Use suitable protection to prevent any mechanical hazards due to persons

loitering within the operating range of the operator. • The electrical cables must

pass through special pipes, ducts and cable glands in order to guarantee adequate

protection against mechanical damage.

Page 3 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

• The electrical cables must not touch any parts that may overheat during use (such

as the motor and transformer). • Before installation, check that the guided part is

in good mechanical condition, and that it opens and closes correctly. • The product

cannot be used to automate any guided part that includes a pedestrian gate, unless

it can only be enabled when the pedestrian gate is secured. • Make sure that nobody

can become trapped between the guided and ﬁ xed parts, when the guided part is set

in motion. If you are automating a pedestrian gate that moves horizontally, this can

be achieved if the corresponding distance is less than 8 mm. However, the distances

indicated below are su cient to avoid trapping the corresponding body parts:

- ﬁ ngers, more than 25 mm;

- feet, more than 50 mm;

- head, more than 300 mm;

- for the entire body, more than 500 mm.

If you cannot achieve these distances, you will need to take suitable safety precautions.

• All ﬁ xed controls must be clearly visible after installation, in a position that allows

the guided part to be directly visible, but far away from moving parts. In the case of

a hold-to-run control, this must be installed at a minimum height of 1.5 m from the

ground and must not be accessible to the public. • Where operated with a hold-to-

run control, install a STOP button to disconnect the main power supply to the operator,

to block movement of the guided part. • If not already present, apply a permanent

tag that describes how to use the manual release mechanism close to it. • Make

sure that the operator has been properly adjusted and that the safety and protection

devices and the manual release are working properly. • Before handing over to the

ﬁ nal user, check that the system complies with the harmonised standards and the

essential requirements of the Machinery Directive (2006/42/EC). • Any residual risks

must be indicated clearly with proper signage a xed in visible areas, and explained

to end users. • Put the machine’s ID plate in a visible place when the installation is

complete. • If the power supply cable is damaged, it must be immediately replaced

by the manufacturer or by an authorised technical assistance centre, or in any case,

by qualiﬁ ed sta , to prevent any risk. • Keep this manual inside the technical folder

along with the manuals of all the other devices used for your automation system.

Page 4 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

• Make sure to hand over to the end user all the operating manuals of the products

that make up the ﬁ nal machinery. • The product, in its original packaging supplied

by the manufacturer, must only be transported in a closed environment (railway

carriage, containers, closed vehicles). • If the product malfunctions, stop using it

and contact customer services at https://www.came.com/global/en/contact-us or via

the telephone number on the website. • The manufacture date is provided in the

production batch printed on the product label. If necessary, contact us at https://

www.came.com/global/en/contact-us. • The general conditions of sale are given in

the o cial CAME price lists.

DISMANTLING AND DISPOSAL

CAME S.p.A. employs an Environmental Management System at its premises. This system is certiﬁ ed and compliant

with the UNI EN ISO 14001 standard to ensure that the environment is respected and safeguarded. Please continue

safeguarding the environment. At CAME we consider it one of the fundamentals of our operating and market strategies.

Simply follow these brief disposal guidelines:

DISPOSING OF THE PACKAGING

The packaging materials (cardboard, plastic, etc.) can be disposed of easily as solid urban waste, separated for recycling.

Before dismantling and disposing of the product, please always check the local laws in force.

DISPOSE OF THE PRODUCT RESPONSIBLY.

DISPOSING OF THE PRODUCT

Our products are made of various materials. Most of these materials (aluminium, plastic, iron and electrical cables) are

classiﬁ ed as solid urban waste. They can be separated for recycling and disposed of at authorised waste treatment plants.

Other components (electronic boards, transmitter batteries, etc.) may contain pollutants.

These must be removed and disposed of by an authorised waste disposal and recycling ﬁ rm.

It is always advisable to check the speciﬁ c laws that apply in your area.

DISPOSE OF THE PRODUCT RESPONSIBLY.

PRODUCT DATA AND INFORMATION

Key

This symbol shows which parts to read carefully.

This symbol shows which parts describe safety issues.

This symbol shows what to tell users.

The measurements, unless otherwise stated, are in millimetres.

Page 5 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Description

801QA-0050

ZLX24MA - Multifunction control panel, with 230 VAC power supply, for 24 V swing gates with two leaves, with programming

display and signalling, safety device self-diagnostics, adaptive speed and torque technology, BUS CXN, 2 safety inputs and

memory space for up to 250 users.

801QA-0070

ZLX24MR - Multifunction control panel, with 120 VAC power supply, for 24 V swing gates with two leaves, with programming

display and signalling, safety device self-diagnostics, adaptive speed and torque technology, BUS CXN, 2 safety inputs and

memory space for up to 250 users.

Technical data

MODELS ZLX24MA ZLX24MR

Power supply (V - 50/60 Hz) 230 AC 120 AC

Motor power supply (V) 36 DC 36 DC

Board power supply (V) 26 AC 26 AC

Standby consumption (W) 33

Power (W) 360 360

Transformer thermal protection (°C) 120 120

Colour RAL 7040 RAL 7040

Operating temperature (°C) -20 ÷ +55 -20 ÷ +55

Storage temperature (°C)* -25 ÷ +70 -25 ÷ +70

Cycles/hour 20 20

Consecutive cycles 20 20

Protection rating (IP) 54 54

Insulation class II

Average life (cycles)** 100.000 100.000

(*) Before installing the product, keep it at room temperature where it has previously been stored or transported at a very

high or very low temperature.

(**) The average product life is a purely indicative estimate. It applies to compliant usage, installation and maintenance

conditions. It is also inﬂ uenced by other factors, such as climatic and environmental conditions.

Fuse table

MODELS ZLX24MA ZLX24MR

Line fuse 3.15 A F 4 A F

Control-board fuse 1.6 A T 1.6 A T

Accessory fuse 1.6 A F 1.6 A F

Page 6 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Description of parts

1 Line fuse

2 Power supply terminal block

3 Terminal board for connecting control devices

4 Terminal board for connecting the safety devices

5 Memory Roll card connector

6 Connector for CAME KEY

7 Display

8 Programming buttons

9 RSE card connector

10 RIO CONN card connector

11 Connector for plug-in radio frequency card (AF)

12 Earthing star point

13 Terminal board for CRP connection

14 Terminal board for connecting the antenna

15 Terminal board for BUS devices

16 Terminal boards for connecting micro limit switches and/

or encoders

17 Terminal board for connecting the gearmotor with

encoder or with slowdown switch and electric lock

18 Accessories fuse

19 Control board fuse

20 Terminal board for connecting the signalling devices

21 Terminal board for power supply to the control board

22 Transformer

Page 7 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Optional accessories

23 RLB battery charger board (002RLB)

24 RGSM001 module (806SA-0010)

25 SMA module (009SMA)

Page 8 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Size

178

125

204 132

195

254

273

==

Page 9 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Cable types and minimum thicknesses

Cable length (m) up to 20 from 20 to 30

Power supply 230 V AC 3G x 1.5 mm² 3G x 2.5 mm²

24 V AC/DC ﬂ ashing beacon 2 x 0.5 mm² 2 x 0.5 mm²

TX Photocells 2 x 0.5 mm² 2 x 0.5 mm²

RX photocells 4 x 0.5 mm² 4 x 0.5 mm²

12 V DC electric lock 2 x 1 mm² 2 x 1.5 mm²

Command and control devices *no. x 0.5 mm² *no. x 0.5 mm²

* no. = see product assembly instructions

Warning: the cable cross-section is indicative and varies according to the motor power and cable length.

When operating at 230 V and outdoors, use H05RN-F cables that are IEC 60245 (IEC 57) compliant; when

indoors, use H05VV-F cables that are IEC 60227 (IEC 53) compliant; For power supplies up to 48 V, use FROR 20-22

II cables compliant with standard EN 50267-2-1 (CEI).

To connect the antenna, use RG58 cable (up to 5 m).

To connect to the CRP, use a UTP CAT5 cable (up to 1,000 m long).

If the cable lengths di er from those speciﬁ ed in the table, deﬁ ne the cable cross-sections according to the

actual power draw of the connected devices and in line with regulation CEI EN 60204-1.

For multiple, sequential loads along the same line, recalculate the values in the table according to the actual

power draw and distances. For information on connecting products not covered in this manual, please see the

documentation accompanying the products themselves.

To connect the encoder, use a FRORPU 3 x 0.5 mm² cable or a cable supplied by CAME on request (item code

801XA-0020).

BUS cable table

We recommend using a FROR 2x1mm² cable, maximum length from the control board: 50 m.

Single branch length (m) max. 50 m

BUS cable 2 x 1 mm²

The total length of all branches can be a maximum of 150 m.

The cable cannot be shielded.

Page 10 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

INSTALLATION

Preparing the control panel

Page 11 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Fastening the control panel

DIN rail

195

125

==

Standard

254

178

Page 12 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

ELECTRICAL CONNECTIONS

Preparing the electrical cables

Connect all wires and cables in compliance with the law.

Use cable glands to connect the devices to the control panel. One of these must be used exclusively for the

power supply cable.

Power supply

1 Connecting to the mains (230/120 V AC - 50/60 Hz)

F - Line fuse

L - Phase

N - Neutral

Earth

The strap used to ﬁ x the cables is not supplied.

N

F

L

Page 13 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

2 Power supply output for accessories

The output normally delivers 26 V AC.

The output delivers 24 V DC (10+, 11-) when the batteries start operating, if they are installed.

3 Electric lock or electromagnets 12 V AC/DC - max 15 W.

10 11 E E3 5

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

Maximum capacity of contacts

The total power of the outputs listed below must not exceed the maximum output power [Accessories]

Device Output Power supply (V) Maximum power (W)

Accessories 10 - 11 26 AC 20

Additional light 10 - E3 26 AC 10

Flashing beacon 10 - E 26 AC 10

Operator status warning

light 10 - 5 26 AC 3

The outputs deliver 24 V DC when the batteries start operating, if they are installed.

Device Output Power supply (V) Power (W)

BUS CXN BUS 15 DC 15

Do not connect anything other than CAME BUS accessories.

Gearmotors

M1 =Gearmotor delayed while opening

M2 =Gearmotor delayed while closing

Where there is only one gearmotor in the system, make the electrical connections on the gearmotor (M2).

Page 14 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

M1 M2

M2M1

Gearmotor with encoder

FC1 FA1 F

E1 -+

M

N

-

E

+

M

N

+

E

-

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

+ E2 -

FC2 FA2 F

E2 -+

FROG-A24E / FERNI / FERNI-V / F4024E / F4024EP

N

M

ENC

N

M

ENC

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

ATS / AXO / FTX / FAST-70 / AMICO / AXI

Page 15 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

N

M

E

N

M

E

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

STYLO-RME

N

M

EB

E

N

M

E

EB

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

STYLO-ME

Gearmotors with slowdown switches

FC1 FA1 F FC2 FA2 F

M

NN

M

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

R

A3024N / A5024N

Page 16 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

FC2 FA2 F

E2 -+

M

N

F

FA

FC

N

M

FC

FA

F

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

FC1 FA1 F

E1 -+

FROG-A24

FC2 FA2 F

E2 -+

M

N

F

FA

RC

N

M

RC

FA

F

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

RR

FC1 FA1 F

E1 -+

F1024

Gearmotors without encoder

M

N

M

M1 N1 ENC1 EB1+VB

R1 M2 N2 ENC2 EB2+VB

R2

M1 M2

Page 17 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Devices with BUS CXN system

The CXN CAME system is a two-wire non-polarised communication BUS which allows you to connect up all compatible CAME

devices.

Connection to the BUS can be in a chain, star or mixed formation.

Once the system has been wired, and after having set the address on each device, the function of each accessory can be

conﬁ gured on the control panel. This method allows you to conﬁ gure the set-up immediately without having to do so later and

intervene directly on the accessories and system wiring.

The CXN BUS can support control devices, interfaces, photocells, safety devices, beacons and gateways at the same time.

Cabling

1 Chain connection

2 Star connection

3 Mixed connection

Cable type

We recommend using a FROR 2x1mm² cable, maximum length from the control board: 50 m.

Single branch length (m) max. 50 m

BUS cable 2 x 1 mm²

The total length of all branches can be a maximum of 150 m.

The cable cannot be shielded.

Page 18 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Maximum number of devices that can be connected, by type

Type of device Maximum number of devices per type

Selectors 7

Photocell pairs 8

Interfaces 2

Flashing beacons 2

BUS CXN device consumption

Scan the QR code to access an interactive table showing consumption data, and calculate the

maximum number of BUS devices you can connect to the control panel.

BUS CXN device consumption is calculated in CXN units.

Page 19 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Command and control devices

1 STOP button (NC contact)

Stop the gate and exclude automatic closing. Use a control device to resume movement.

When the contact is being used, it must be activated during programming.

See the [F1 – Total stop] function.

2 Control device (NO contact)

Open command

When the [F6 – Hold-to-run] function is active, a control device must be set to OPEN.

3 Control device (NO contact)

Partial Opening or Pedestrian command

See function [F36 - Adjusting partial opening].

4 Control device (NO contact)

Close command

When the function [F6 - Hold-to-run] is active, a control device must be set to CLOSE.

5 Control device (NO contact)

Step-by-step command

Sequential command

Open-Close command

See function [F7 - 2-7 command].

6 Antenna with RG58 cable

If the chosen signalling device can be ﬁ tted with an antenna, use the terminal shown to connect it.

1 2 3 3P 4 7

BUS

Page 20 - Manual FA01885-EN - 08/2022 - © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. - Translation of the original instructions

Signalling devices

1 Flashing beacon

It ﬂ ashes when the operator opens and closes.

2 Additional light

It increases the light in the manoeuvring area.

See function [F18 - Additional light].

3 Operator status warning light

It notiﬁ es the user of the operator status.

See function [F10 - Passage-open warning light].

10 11 E E3 5

Page is loading ...