Dell 14R Owner's manual

Inspiron 14/14R

Owner’s Manual

Computer model: Inspiron 3421/5421

Regulatory model: P37G

Regulatory type: P37G001

book.book Page 1 Tuesday, November 27, 2012 12:06 PM

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make

better use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss

of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage,

personal injury, or death.

____________________

Trademarks used in this text: Dell

™

, the DELL logo, and Inspiron

™

are trademarks of

Dell Inc.; Microsoft

®

, Windows

®

, and the Windows start button logo are either trademarks

or registered trademarks of Microsoft Corporation in the United States and/or other

countries; Bluetooth

®

is a registered trademark owned by Bluetooth SIG, Inc. and is used

by Dell under license.

2012 - 11 Rev. A00

book.book Page 2 Tuesday, November 27, 2012 12:06 PM

Contents | 3

Contents

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Turn Off Your Computer and Connected Devices. . . . . 9

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . 10

Recommended Tools. . . . . . . . . . . . . . . . . . . . . . . 10

After Working Inside Your Computer . . . . . . . . . . 11

Removing the Battery . . . . . . . . . . . . . . . . . . . . . . 12

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . 13

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Removing the Optical Drive . . . . . . . . . . . . . . . . . 14

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Replacing the Optical Drive . . . . . . . . . . . . . . . . . 16

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Removing the Keyboard . . . . . . . . . . . . . . . . . . . . 17

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . 20

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Removing the Base Cover . . . . . . . . . . . . . . . . . . . 21

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

book.book Page 3 Tuesday, November 27, 2012 12:06 PM

4 | Contents

Replacing the Base Cover . . . . . . . . . . . . . . . . . . . 22

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Removing the Memory Module(s). . . . . . . . . . . . . 23

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Replacing the Memory Module(s). . . . . . . . . . . . . 24

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Removing the Hard Drive . . . . . . . . . . . . . . . . . . . 25

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Replacing the Hard Drive. . . . . . . . . . . . . . . . . . . . 27

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Removing the Wireless Mini-Card . . . . . . . . . . . . 28

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Replacing the Wireless Mini-Card . . . . . . . . . . . . 30

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Removing the Palm-Rest. . . . . . . . . . . . . . . . . . . . 31

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Replacing the Palm-Rest . . . . . . . . . . . . . . . . . . . . 35

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

book.book Page 4 Tuesday, November 27, 2012 12:06 PM

Contents | 5

Removing the Coin-Cell Battery. . . . . . . . . . . . . . 36

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Replacing the Coin-Cell Battery . . . . . . . . . . . . . . 38

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Removing the I/O Board . . . . . . . . . . . . . . . . . . . . 39

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Replacing the I/O Board . . . . . . . . . . . . . . . . . . . . 41

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Removing the Power-Adapter Port . . . . . . . . . . . 42

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Replacing the Power-Adapter Port . . . . . . . . . . . 45

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Removing the System Board . . . . . . . . . . . . . . . . . 46

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Replacing the System Board . . . . . . . . . . . . . . . . . 49

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Entering the Service Tag in system setup. . . . . . . . . . 50

Removing the Thermal-Cooling Assembly . . . . . 51

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

book.book Page 5 Tuesday, November 27, 2012 12:06 PM

6 | Contents

Replacing the Thermal-Cooling Assembly . . . . . 52

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Removing the Speakers . . . . . . . . . . . . . . . . . . . . . 53

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Replacing the Speakers . . . . . . . . . . . . . . . . . . . . . 55

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Removing the Display Assembly . . . . . . . . . . . . . . 56

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Replacing the Display Assembly . . . . . . . . . . . . . . 58

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Removing the Display Bezel . . . . . . . . . . . . . . . . . 59

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Replacing the Display Bezel . . . . . . . . . . . . . . . . . 61

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Removing the Display Hinges . . . . . . . . . . . . . . . . 62

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Replacing the Display Hinges . . . . . . . . . . . . . . . . 64

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

book.book Page 6 Tuesday, November 27, 2012 12:06 PM

Contents | 7

Removing the Display Panel . . . . . . . . . . . . . . . . . 65

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Replacing the Display Panel . . . . . . . . . . . . . . . . . 67

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Removing the Camera Module . . . . . . . . . . . . . . . 68

Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Replacing the Camera Module . . . . . . . . . . . . . . . 70

Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Flashing the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . 71

book.book Page 7 Tuesday, November 27, 2012 12:06 PM

8 | Contents

book.book Page 8 Tuesday, November 27, 2012 12:06 PM

Before You Begin | 9

Before You Begin

Turn Off Your Computer and Connected Devices

CAUTION: To avoid losing data, save and close all open files and exit all open

programs before you turn off your computer.

1 Save and close all open files and exit all open programs.

2 Shut down your computer.

• Windows 8:

a Point your mouse pointer to the upper-right or lower-right corner of the

screen to open the Charms sidebar.

b In the Charms sidebar, click Settings→ Power→ Shut down.

• Windows 7:

Click Start and click Shut down.

Microsoft Windows shuts down and then the computer turns off.

NOTE: If you are using a different operating system, see the documentation

of your operating system for shut-down instructions.

3 Disconnect your computer and all attached devices from their electrical outlets.

4 Disconnect all telephone cables, network cables, and attached devices from your

computer.

5 After you unplug all the cables from the computer, press and hold the power

button for 5 seconds to ground the system board.

book.book Page 9 Tuesday, November 27, 2012 12:06 PM

10 | Before You Begin

Safety Instructions

Use the following safety guidelines to protect your computer from potential damage and

ensure your personal safety.

WARNING: Before working inside your computer, read the safety information

that shipped with your computer. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

WARNING: Disconnect all power sources before opening the computer cover or

panels. After you finish working inside the computer, replace all covers, panels,

and screws before connecting to the power source.

CAUTION: To avoid damaging the computer, ensure that the work surface is flat

and clean.

CAUTION: To avoid damaging the components and cards, handle them by their

edges and avoid touching pins and contacts.

CAUTION: Only a certified service technician is authorized to remove the

computer cover and access any of the components inside the computer. See the

safety instructions for complete information about safety precautions, working

inside your computer, and protecting against electrostatic discharge.

CAUTION: Before touching anything inside your computer, ground yourself by

touching an unpainted metal surface, such as the metal at the back of the

computer. While you work, periodically touch an unpainted metal surface to

dissipate static electricity, which could harm internal components.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab,

not on the cable itself. Some cables have connectors with locking tabs or

thumb-screws that you must disengage before disconnecting the cable.

When disconnecting cables, keep them evenly aligned to avoid bending any

connector pins. When connecting cables, ensure that the connectors and ports

are correctly oriented and aligned.

CAUTION: To disconnect a network cable, first unplug the cable from your

computer and then unplug the cable from the network device.

CAUTION: Press and eject any installed card from the media-card reader.

Recommended Tools

The procedures in this document may require the following tools:

• Phillips screwdriver

• Plastic scribe

book.book Page 10 Tuesday, November 27, 2012 12:06 PM

After Working Inside Your Computer | 11

After Working Inside Your Computer

After you complete the replacement procedures, ensure the following:

• Replace all screws and ensure that no stray screws remain inside your computer.

• Connect any external devices, cables, cards, and any other part(s) you removed

before working on your computer.

• Connect your computer and all attached devices to their electrical outlets.

CAUTION: Before turning on your computer, replace all screws and ensure

that no stray screws remain inside the computer. Failure to do so may damage

your computer.

book.book Page 11 Tuesday, November 27, 2012 12:06 PM

12 | Removing the Battery

Removing the Battery

WARNING: Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on

page 9. After working inside your computer, follow the instructions in "After

Working Inside Your Computer" on page 11. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

1 Close the display and turn the computer over.

2 Slide the battery latches to the unlock position. You hear a click when the battery is

unlocked.

3 Lift and remove the battery off the computer base.

1 battery latches (2) 2 battery

1

2

book.book Page 12 Tuesday, November 27, 2012 12:06 PM

Replacing the Battery | 13

Replacing the Battery

WARNING: Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on

page 9. After working inside your computer, follow the instructions in "After

Working Inside Your Computer" on page 11. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

Align the tabs on the battery with the slots on the battery bay and snap the battery

into place.

book.book Page 13 Tuesday, November 27, 2012 12:06 PM

14 | Removing the Optical Drive

Removing the Optical Drive

WARNING: Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on

page 9. After working inside your computer, follow the instructions in "After

Working Inside Your Computer" on page 11. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Prerequisites

Remove the battery. See "Removing the Battery" on page 12.

Procedure

1 Remove the screw that secures the optical-drive assembly to the computer base.

2 Using your fingertips, slide the optical-drive assembly out of the optical-drive bay.

3 Remove the screw that secures the optical-drive bracket to the optical-drive

assembly and remove the optical-drive bracket.

1 optical-drive assembly 2 screw

1

2

book.book Page 14 Tuesday, November 27, 2012 12:06 PM

Removing the Optical Drive | 15

4 Carefully pull the optical-drive bezel and remove it from the optical drive.

1 screw 2 optical-drive bracket

3 optical drive 4 optical-drive bezel

3

2

4

1

book.book Page 15 Tuesday, November 27, 2012 12:06 PM

16 | Replacing the Optical Drive

Replacing the Optical Drive

WARNING: Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on

page 9. After working inside your computer, follow the instructions in "After

Working Inside Your Computer" on page 11. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

1 Align the tabs on the optical-drive bezel with the slots on the optical drive and snap

the optical-drive bezel into place.

2 Align the screw hole on the optical-drive bracket with the screw hole on

the optical-drive assembly and replace the screw that secures the optical-drive

bracket to the optical-drive assembly.

3 Slide the optical-drive assembly into the optical-drive bay and ensure that the

screw hole on the optical-drive bracket aligns with the screw hole

on computer base.

4 Replace the screw that secures the optical-drive assembly to the computer base.

Postrequisites

Replace the battery. See "Replacing the Battery" on page 13.

book.book Page 16 Tuesday, November 27, 2012 12:06 PM

Removing the Keyboard | 17

Removing the Keyboard

WARNING: Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on

page 9. After working inside your computer, follow the instructions in "After

Working Inside Your Computer" on page 11. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Prerequisites

Remove the battery. See "Removing the Battery" on page 12.

Procedure

1 Remove the screws that secure the keyboard to the computer base

1screws (2)

1

book.book Page 17 Tuesday, November 27, 2012 12:06 PM

18 | Removing the Keyboard

2 Turn the computer over and open the display as far as possible.

3 Using a plastic scribe, pry the keyboard from the tabs on the palm-rest.

1 tabs (5) 2 plastic scribe

3keyboard

1

2

3

book.book Page 18 Tuesday, November 27, 2012 12:06 PM

Removing the Keyboard | 19

4 Lift and slide the keyboard towards the display to release the keyboard from the

palm-rest and place the keyboard on the palm-rest.

5 Lift the connector latch and disconnect the keyboard cable from the

keyboard-cable connector.

6 Lift the keyboard off the palm-rest.

1 keyboard 2 palm-rest

3 keyboard cable 4 connector latch

4

3

1

2

book.book Page 19 Tuesday, November 27, 2012 12:06 PM

20 | Replacing the Keyboard

Replacing the Keyboard

WARNING: Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on

page 9. After working inside your computer, follow the instructions in "After

Working Inside Your Computer" on page 11. For additional safety best practices

information, see the Regulatory Compliance Homepage at

dell.com/regulatory_compliance.

Procedure

1 Slide the keyboard cable into the keyboard-cable connector and press down on the

connector latch to secure the cable.

2 Slide the tabs at the bottom of the keyboard into the slots on the palm-rest and

place the keyboard on the palm-rest.

3 Gently press around the edges of the keyboard to secure the keyboard under the

tabs on the palm-rest.

4 Replace the screws that secure the keyboard to the computer base.

Postrequisites

Replace the battery. See "Replacing the Battery" on page 13.

book.book Page 20 Tuesday, November 27, 2012 12:06 PM

Page is loading ...

Dell 14R, Inspiron 14R 3421, Inspiron 14R 5421 Owner's manual

Related papers

Other documents