Lucent Technologies SuperPipe 155 Hardware Install Manual

Brand: Lucent Technologies

Model: SuperPipe 155

Category: Networking

Type: Hardware Install Manual

This manual is also suitable for

SuperPipe 95

Lucent Technologies SuperPipe 155 is a versatile networking device that offers a range of capabilities for connecting and managing your network. With its support for ISDN, T1, E1, V.35, and Ethernet interfaces, the SuperPipe 155 can seamlessly integrate with various WAN and LAN technologies. It provides two analog phone ports, allowing you to connect regular telephones or fax machines for convenient communication. The SuperPipe 155 also features a terminal port for direct configuration and diagnostics, ensuring easy management and troubleshooting.

SUPERPIPE 95/155

HARDWARE INSTALL GUIDE

Lucent Technologies

Part Number: 7820-0257-002

For software version 7.4.10

March 2000

Review Package Contents

Before You Begin

The SuperPipe package also contains:

• Hardware Install Guide and Quick

Configuration Guide.

• Pipeline Companion CD-ROM.

• Warranty card.

• For SuperPipe155 only, one RJ-48C T1

crossover cable (part number 2510-0059-001).

• Power plug adapters for international units.

Also, please ensure that you have the following.

• WAN interface(s)

–ISDN

– T1 or E1 service (SuperPipe 155 only)

• A computer with a serial port and a 10/100

Base-T Ethernet interface.

• If you have the V.35 version of the SuperPipe

155, you will need a V.35/X.21 cable.

This section describes how to connect an ISDN BRI

line to the SuperPipe. If you are not connecting an

ISDN line go on to step 2. Otherwise, refer to the

section that applies to you:

• Connect an ISDN BRI line with a U interface

• Connect an ISDN BRI line with an S interface

Connect an ISDN BRI line with

a U interface

Cable needed: RJ-48C to RJ-11 ISDN cable (pro-

vided, has blue ends).

To connect an ISDN BRI line with a U interface, do

the following:

1 Insert the larger jack of the cable with the blue

ends (RJ-48C to RJ-11 ISDN) into one of the

WAN-BRI jacks on the back of the SuperPipe.

2 Insert the other end of the cable into the ISDN

wall jack.

3 To connect an additional ISDN BRI line, repeat

steps 1 and 2.

Connect an ISDN BRI line with

an S interface

To connect an ISDN BRI line with an S interface,

do the following:

Cable needed: RJ-48C to RJ-11 ISDN cable

(provided, has blue ends).

1 Insert the larger jack of the cable with the blue

ends (RJ-48C to RJ-11 ISDN) into one of the

WAN-BRI jacks on the back of the SuperPipe.

2 Insert the other end of the cable into an NT-1 or

an ISDN wall jack with an integrated NT-1.

3 To connect an additional ISDN BRI line, repeat

steps 1 and 2.

Connect ISDN BRI Line(s)

If you are not connecting a T1 or E1 or serial WAN

line, go on to Step 3. Otherwise, refer to the appro-

priate section.

T1 or E1 Connection

Cable needed: RJ-48C T1/E1 crossover cable (pro-

vided with SuperPipe 155 only).

1 Connect your leased line to the port labeled

WAN T1 or E1 on the SuperPipe’s back panel.

2 Connect the other end either directly to the wall

jack or through other network interface equip-

ment.

3 After you inform your service provider that

your equipment is connected and ready for ser-

vice, you are ready to start up the unit.

CAUTION: The RJ-48C cable provided

with your SuperPipe is for devices that

transmit on pins 4 and 5 and receive on

pins 1 and 2. Ask your carrier what type

of cable to use, a straight-through or

crossover.

V.35 Connection

Cable needed: DB44-to-DB25 cable (not pro-

vided).

1 Connect the DB-44 end into the S-WAN port

on the back of the SuperPipe unit.

2 Connect the DB25 end into the V.35 port of the

other device.

Connect T1, E1 or V.35

(Model 155)

Refer to the section that applies to your network:

• Connect a single computer to a SuperPipe

• Connect your Superpipe to an existing 10/100

Base-T Ethernet network using a hub

Connect to a single computer

Cable Needed: Yellow-ended 10/100 Base-T

Ethernet crossover cable (provided).

1 Insert one end of the 10/100 Base-T cable into

the 10/100 Base-T jack on the back of the

SuperPipe.

2 Insert the other end of the cable into the 10/100

Base-T Ethernet jack on the computer.

Connect to an Ethernet hub

Cable Needed: 10/100 Base-T Ethernet cable (you

provide).

CAUTION: Do not use the 10/100 Base-

T crossover cable included with the

SuperPipe (part number 2510-0084-001)

to connect the SuperPipe to a 10/100

Base-T hub.

Connect Superpipe to Computer(s)

Connect Analog Equipment

The SuperPipe has two analog ports providing you

with the option of using “regular” telephones or fax

machines over your SuperPipe.

To connect a telephone or other analog telephone

equipment:

1 Connect one end of a modular telephone

hookup cable to a conventional telephone or

other telephone device.

2 Connect the other end of the cable to the Phone

port 1 on the SuperPipe. International

customers may need to insert an analog port

adapter into the SuperPipe analog port.

Note: You cannot place or receive calls until you

connect the power cable to the SuperPipe, configure

the ISDN line and configure one or both of the

SuperPipe Phone ports to use the ISDN WAN

channels.

Connecting to the terminal (serial) port is one of

two methods by which you can enter settings and

run diagnostics using the on-board software of the

SuperPipe. Using the Ethernet connection is the

other method.

For PC Users

Cable needed: Serial cable (provided) and, possi-

bly, a DB-9-to-DB25 serial cable adapter (pro-

vided).

1 Connect a modem cable to a serial connector

on your computer and note the serial port num-

ber.

2 If the plug at the other end of the modem cable

has 25 pins, connect the 25-to-9 pin adapter

included with the SuperPipe to the plug.

3 Connect the cable to the Terminal port on the

back of the SuperPipe unit.

For Unix Users

Cable needed: Serial cable (provided).

1 Connect a modem cable for the computer to the

Terminal port on the back of the SuperPipe.

2 Connect the other end of the cable to the serial

port on the computer.

For Macintosh Users

Cable needed: Serial cable (you provide) and a 25-

pin-to-9 pin adapter (provided).

1 Connect the 25-to-9 pin adapter to the DB-25

end of a Macintosh modem cable.

2 Connect the cable to the Terminal port on the

back of the SuperPipe.

3 Connect the other end of the cable to a serial

port (either the Modem or Printer port) on the

computer.

Connect to the Terminal Port

The local BRI port allows you to support an ISDN

telephone, desktop CODEC video conferencing, or

other ISDN desktop equipment.

Cable needed: RJ-48C to RJ-11 ISDN cable.

If the two ISDN cables provided are already in use,

you must provide this cable.

1 Connect one end of the ISDN cable into the

line jack on the ISDN telephone or other ISDN

device.

2 Connect the other end of the cable to the local

ISDN S/T BRI port on the SuperPipe.

Connect ISDN BRI Equipment

Connect the Power Cable

1 Plug the end of the cord on the power supply

to the power jack of the SuperPipe.

2 Connect the opposite end of the power unit

into the appropriate power cord provided.

3 Insert the opposite end of the power plug into

an electrical outlet.

4 Turn the power switch on the back panel to

“ON.” The PWR status light on the front pan-

els illuminates indicating that the power is on.

WARNING: Models with AC power

inputs are intended for use with a three-

wire grounding type plug--that is, a plug

that has a grounding pin. This is a safety

feature. Equipment grounding is vital to

ensure safe operation. Do not defeat the

purpose of the grounding type plug by

modifying the plug or using an adapter.

If the power supply is fed from a power source

with no ground path, connect the unit chassis stud

to the power supply chassis ground via a solid

copper 12 AWG wire. If the power supply is fed

from an isolated power source, the chassis ground

must be connected directly to earth via a solid cop-

per 12 AWG wire.

Refer to the following illustration to understand the functionality of the SuperPipe 155 and SuperPipe 95

front panel LEDs.

Power

ON (green)=

Power is being

supplied to the

unit.

OFF

=Power is

not being

supplied to

the unit.

Fault

OFF=

Functioning

correctly.

ON (red)

Problem

detected.

LAN LEDs

-----------------------------------------------------------------

LNK

ON (green)=Link active.

OFF=

Link inactive.

ACT

Flashes (green)

when packets

are transmitted or received.

COL

Flashes (amber)

when

collisions are taking place

on the Ethernet LAN.

10/100BT

ON (green)

= Link running

at 100 Mbps.

OFF

=Link running at 10 Mbps.

ON (green)

= Allows bidirectional,

simultaneous communication (full

duplex link).

OFF

=Information is carried in one

direction at a time (half duplex link).

Phone Port Status

--------------------------

ON (amber)=

Telephone port

is in use.

OFF=

Telephone port is available

for use.

Flashing

=Device connected to

telephone port is ringing.

T1/E1/V.35 Status

(SuperPipe 155)

-------------------------

ACT

ON=

Active link.

FLASHING=

Error.

OFF= Port

disabled

ISDN BRI LEDs

---------------------------------

B1/B2 Channel Activity

GREEN = data call

in progress.

AMBER = voice call

in progress.

Flashes when call is

initiated.

D Channel Activity

ON (green) =active ISDN line.

OFF = ISDN line inactive.

Flashes when line activation

is in progress.

Understanding the SuperPipe LEDs

Lucent Technologies SuperPipe 155 Hardware Install Manual

Brand: Lucent Technologies

Model: SuperPipe 155

Category: Networking

Type: Hardware Install Manual

This manual is also suitable for

SuperPipe 95

Download PDF

report

Lucent Technologies SuperPipe 155 Hardware Install Manual

This manual is also suitable for

Lucent Technologies SuperPipe 155 Hardware Install Manual

Related papers

Other documents