Wolf Garten 2.48 A HW User manual

Page is loading ...

4

2.48 A HW

D

1 Antriebsbügel

2 Startergriff

3 Grasfangsack

4 Schutzklappe

5 Schnitthöheneinstellung -/anzeige

6 Luftfilter

7 Benzineinfüllstutzen

8 Primer

9 Sicherheitsbügel

10 Öleinfüllstutzen

11 Zündkerze

G

1 Drive clutch bail arm

2 Recoil starter

3 Catcher bag

4 Deflector blate

5 Cutting height adjustment /Indicator of cut-

ting heigth

6 Air cleaner

7 Petrol filter cap

8 Cold starting primer

9 Operator presence bail arm

10 Engine oil check/fill

11 Sparking plug

F

1 Etrier du mécanisme d‘entrainement

2 Poignée de starter

3 Bac de remassage

4 Clapet de sécurité

5 Reglage de la hauteur de coupe/Croquis

de la hauteur de coupe

6 Pré-filtre

7 Bouchon du réservoir

8 Démarreur

9 Etrier de sécurité

10 Remplissage d‘huile

11 Bougie d’allumage

I

1 Archi di azionamento

2 Raccoglierba

3 Sacco di raccolta

4 Deflettore

5 Regolazione l‘atezza di taglio/Bocchetto-

ne per olio

6 Filtro

7 Coperchio del serbatio

8 Primer

9 Archi di sicurezza

10 Bocchettone per olio

11 Candela di accensione

n

1 Aandrijfbeugel

2 Starterknop

3 Opvangreservoir

4 Achterklep

5 Maaihoogte instelling -/ aanwijzing

6 Luchtfilter

7 Tankdeksel

8 Primer

9 Veiligheidsbeugel

10 Olie vulopening

11 Bougie

d

1Trækbøjle

2 Startergreb

3 Opsamlingsbakke

4 Beskyttelsesklap

5 Indstilling af klippehøjde/Indikator for klip-

pehøjde

6 Luftfilter

7 Tankpåfyldningsstuds

8 Primer

9 Sikkerhedsbøjle

10 Oliepåfyldningsstuds

11 Tændrør

Page is loading ...

12

G

G Congratulations on your purchase of a WOLF lawn mower

Contents

Technical data . . . . . . . . . . . . . . . . . . . .12

Safety instructions . . . . . . . . . . . . . . . . . .13

Assembly . . . . . . . . . . . . . . . . . . . . . . .14

Operation . . . . . . . . . . . . . . . . . . . . . .15

Maintenance . . . . . . . . . . . . . . . . . . . . .16

Spare parts . . . . . . . . . . . . . . . . . . . . . .16

Faults and how to remedy . . . . . . . . . . . . . .17

Guarantee conditions. . . . . . . . . . . . . . . . .17

A quick guide to features

–

Comfort-wheels in XXL format, wheel diameter 28 cm

– Extremely nimble on unlevel ground

– Central cutting height setting

– Fold-down handle for space-saving storage and easy trans-

port

– Easily emptied, capacious catchment bag

– High-quality materials, excellent workmanship and attractive

design

– Ready-to-use: From 0 to mowing mode in 30 second

Technical data

It is important that you read, fully understand and ob-

serve the following safety precautions and warnings.

Careless or improper use of the machine may cause

serious or fatal injury. The user is responsible for any

accidents involving other people or other people‘s pro-

perty.

Never let children or other persons who are not familiar

with the operating instructions use the lawn mower. Ju-

veniles under l6 years may not use the equipment. Lo-

cal regulations may specify the minimum legal age of

the operator.

We reserve the right of technical changes.

D Measurement of noise at the operator's ear according to EN

836.

E Measurement of vibrations at the handlebar held by the ope-

rator according to EN 1033, EN 836. The typical weighted

acceleration is:

2.48 A HW

Typ 4238 ...

A 90 cm

B 47 cm

C 54 cm

D LP 83 dB (A)

E a

hw

7,1 m/s

2

Grass catcher 65 l

Wheel drive 1-speed / 3,5 km/h

Cutting width 48 cm

Cutting height 3,0 - 7,0 cm

Weight 33 kg

Briggs & Stratton

Nominal power 2,4 kW

Maximum power 2,9 kW

Capacity 158 ccm

Spark plug Champion RJ 19 LM

Tank capacity 0,9 l

Oil 0,6 l / HD SAE 30

Instruction Manual

13

G

Safety instructions

Meaning of the symbols

General information

z This lawnmower is designed for domestic grass and lawn sur-

faces. Because of the physical risk to the user or to others, the

lawnmower must not be used for other purposes.

z Never mow the lawn if others – in particular children and ani-

mals – are in the vicinity.

z Only mow the lawn during daylight or with the aid of appropri-

ate artificial light.

Before Mowing

z Never mow without wearing sturdy footwear and long trou-

sers: Never mow barefoot or in open sandals.

z Attach the baffle provided and/or grass box. Make certain that

it is firmly fitted. Operation without or with damaged protective

equipment is forbidden.

z Examine the area on which the machine is to be used and re-

move all objects which are capable of being contacted or

thrown by the mower or its blade.

z Check the machine to make certain that all fasteners, bolts &

nuts are tightly fitted; check also for signs of damage or se-

rious wear.

z Observe the installation instructions when replacing parts - if

in doubt always refer to your WOLF Service Centre.

z Examine the grass box regularly for wear or damage - replace

as necessary.

z Mowers fitted with four-stroke engines must be provided with

engine oil before the first start-up (see „Filling Oil”).

z Check the oil level before each use.

z WARNING - petrol is highly inflammable! Do not smoke. Do

not refuel in any area where there may be a naked flame.

z Keep fuel only in purpose-designed containers.

z Only refuel outdoors.

z Pour in fuel (REGULAR GRADE FUEL) before starting the en-

gine.

z Always firmly tighten petrol filler cap.

z Do not refuel or remove the tank filler cap while the engine is

running or when the machine is hot.

z Do not attempt to start the engine if gasoline spills out. In-

stead, the machine should be removed from the area where

the petrol was spilled. Any attempt to start the mower should

be delayed until the fuel vapours have evaporated.

z Replace the engine exhaust silencer if defective.

z Before use a visual inspection should also be made in order to

determine whether the blade, fasteners and the mower deck

are worn or damaged. In order to avoid damaging vibration

caused by imbalance, worn out or damaged blades and fit-

tings must only be replaced as a set.

z For safety reasons the fuel filler cap must be replaced when

damaged.

z Check the fuel line connections, air filter fittings, etc. for tight-

ness.

When starting the engine

z Only start the engine if your hands and feet are at safe dis-

tance from the mower deck and blade.

z Before you start the engine, disengage the drive.

z When starting or switching on the engine the lawn mower

must not be tilted, unless the lawn mower must be raised for

the procedure. In this case, you tilt it only so far as is absolu-

tely necessary and only raise the side turned away from the

operator.

z Do not let the engine run in closed areas in which dangerous

carbon monoxide may accumulate.

z Start the mower on an even surface, not in tall grass.

z Do not start the engine if you are standing in front of the di-

scharge channel.

When Mowing

z WARNING, DANGER! Rotating blade!

z Do not attempt to touch the blade when it is running.

z Observe the safety distance provided by the handlebars and

bail arms.

z Only start the engine if your feet are at a safe distance from

the blade.

z Make certain that you have a secure foothold, particularly on

slopes. Never run, always walk calmly.

z Always mow slopes along the contours, not up and down the

slope.

z Particular care is required on slopes as you change direction.

z Be particularly careful when you turn the mower and pull it to-

wards you.

z Switch off the mower, if you tilt it, run it dry or when transpor-

ting it.

z Never use the lawn mower with damaged protection guards,

safety devices or grilles or without the protection devices at-

tached, e.g. baffle plates and/or grass box.

z Do not change the governor adjustment of the engine or

attempt to adjust it.

z The blade must be stopped if the lawn mower is moved off the

lawn.

z Before you raise or carry the mower switch off the engine off

and wait until the blade has come to a complete stop.

z Adjust the cutting height only with the engine switched off and

with the blade at a standstill.

z Never open the protection flap if the engine is still running.

Attention!

Read Instruction

manual before

use!

Keep bystan-

ders away!

Sharp blades-

Beware of cutting

fingers or toes -

Remove spark

plug lead before

maintenance.

14

G

z Before removing the grass box: Turn off the engine and wait

for the blade to stop. Carefully refit the grass box after emp-

tying.

z Never drive over gravel with the engine running - stones can

be thrown by contact with the blade!

z Where possible, do not mow in wet grass. If the mower ap-

pears to have blocked, turn off the engine, remove the spark

plug lead and wait until the blade comes to a standstill if, for

example:

– to free a blockage in the ejection channel

– to examine or clean the mower

– if a foreign body is encountered. Check whether mower

deck or blade have been damaged. Then correct or repair

the damage before recommencing mowing.

– if the mower strongly vibrates from imbalance (then switch

off immediately and look for the cause).

z NOTE: Danger when grass box equipment is inappropriately

handled.

z If the mower is a self-propelled version then release the drive

clutch bail before you switch on the engine. Do not touch en-

gine or exhaust during or shortly after operation. Hot parts can

lead to burns or provoke frightened movements which may

lead to injuries.

z Turn the engine off if you the leave the lawn mower unatten-

ded and before you refuel.

After working

z The throttle should be closed before switching off the engine.

If the engine is equipped with a petrol shut-off valve then this

be closed after mowing has been completed.

z Do not leave the mower in closed areas after switching off - al-

low it to cool off in the open air before storing away.

z Never keep the machine with petrol in the tank within a buil-

ding in which gasoline vapours may possibly come into con-

tact with naked flames or sparks. Before leaving the mower

remove the spark plug lead and - if fitted - the starting key.

z Lifting and carrying the mower for transport:

z Never attempt to lift the mower with the engine running - nor

with a hot engine - always remove the spark plug lead before

lifting or carrying.

z When folding the mower handlebars, detach starter rope and

make certain that the control cables are not snagged or stret-

ched when folding or unfolding.

z Always carry out the engine oil change with the fuel tank em-

pty and filler cap fitted. The engine should be warmed up prior

to draining the oil to ensure all sludge deposits are drained

away with the oil.

Maintenance

z Regularly examine all fixing bolts and nuts, particularly those

of the cutter bar, for tightness.

z Maintenance and cleaning of the equipment as well as remo-

ving the protection device may only be performed with the en-

gine stopped and the spark plug lead and - if available - the

starting key, removed.

z Note information on the chassis before cleaning and oil

change!

z Make certain that all nuts, pins and screws are firmly tightened

and that the unit is in a safe operating condition.

z In order to avoid the risk of fire keep the engine, exhaust, bat-

tery box and the area around the fuel tank free of grass, leaves

or oil.

z If the equipment must be tilted for maintenance work then the

fuel must be completely drained from the tank beforehand.

z Clean the equipment after each use with a hand-brush - not

with water and do not hose down with a high pressure hose in

particular. Make certain to keep the engine cooling fins and

engine cooling air intake clean and free from debris.

z Do not place the equipment in damp areas, near naked flames

or where a spark might ignite petrol vapour.

z If the fuel tank is to be emptied then this should be done out-

doors. Make sure that no fuel is spilled.

z For safety reasons replace worn out or damaged parts.

z NOTE! Always have blades replaced or sharpened by a

WOLF Service Centre, as a blade balance test must be per-

formed in accordance with safety regulations and the blade re-

taining bolt must be tightened to a specified torque.

z Wear suitable work gloves when carrying out the above work,

especially when handling the blade.

Assembly

Fixing of handle

1 ATTENTION! Take care that the switch cable does not

become caught and crused when folding the handle fra-

me.

Fasten the handle bar as in the illustration.

Mount grass catcher

z See illustrations.

A

B

C

D

E

F

15

G

Operation

Operating times

z Please check noise abatement regulations prevailing in your

country.

Starter cord assembly

1. Lift and hold operator presence bail arm (1).

2. Pull the starter rope slowly to the holding bracket.

3.

Twist the cord through the holder .

3 Always remove the starter cord from the holder before

folding the mower handles.

Oil Fill

1 Check oil level with mower standing on level ground.

Fill crankcase with quality oil SAE 30 up to the mark „Full“

on dipstick. (Do not overfill.) Capacity approx. 0,6 litre.

Screw in dipstick according to illus.

Filling with fuel

1 Caution! Rotating blades

Settings only to be carried out on the machine with the mo-

tor switched off and with the working tools at a standstill.

z Use only normal lead-free petrol (not Super unleaded).

z Avoid spilling petrol.

z Do not inhale the vapour.

Hang up collection bag

1 Attention! Rotary cutter blade

Undertake adjustments on the equipment only after the

motor is switched off and the cutting tool has come to a

standstill.

1. Lift the protective flap.

2. Hang the grass bag in the chassis with the hooks in the reces-

ses (see arrow).

3. Replace the protective flap.

Set cut height

1 Attention! Rotary cutter blade

Undertake work/adjustments on the equipment only after

the motor is switched off and the cutting tool has come to a

standstill.

1. Pull the lever out.

2. Set the desired cutting height.

3. Press the lever back in.

Selection of Cutting height

z If possible, mow when grass is dry in order to protect turf. Do

not se cutting position too low when mowing very hight or wet

grass.

z We recommend an average cutting height of 40-50 mm.

Start

z On a flat surface, if possible not in high grass.

Cold start

1. Firmly press the primer on the motor three times.

2. Raise and hold the safety bracket (1).

3. Pull starter grip and return it slowly by hand.

Wheel drive

1. Wheel drive on: Raise drive bracket (2).

2. Wheel drive off: Relapse drive bracket (2).

Warm start

1. Raise and hold the safety bracket (1).

2. Pull starter grip and return it slowly by hand.

Stop Motor

z Release safety bracket (2).

3 If the motor does not start in cold weather, press the

primer.

Emptying of Grassbox

The grassbox is full and should be emptied as soon as grass clip-

pings remain uncollected on the ground behind your mower.

1 Attention! Rotary cutter blade

Undertake adjustments on the equipment only after the

motor is switched off and the cutting tool has come to a

standstill.

z Empty collection bag.

z Remove potential blockages in the cutting space before

starting.

Tips for mowing

z To prevent strips of grass from being left unmowed, the cutting

paths must always overlap a few centimeters .

Fixing of handle

z Take care that the switch cable does not be-come caught and

crushed when folding the handlebar.

G

H

J

K

L

M

N

G

H

G

H

G

O

16

G

Maintenance

General

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

z For safety reasons, replace any worn or damaged parts.

When replacing, follow the instructions for installation

z Check all the visible fastening bolts and nuts regularly to be

sure they are snug and tighten them.

z Only use spare parts made by WOLF; otherwise you do not

have a guarantee that your mower meets safety regulations.

Cleaning operations and blade change

1. Pull off the sparkplug connector!

2. Raise the cutting height to its highest position .

3. For cleaning and changing the blade, tip the mower to the side

as illustrated .

Sharpening and changing blade

1 Caution! Rotating blades

Before all maintenance and cleaning tasks:

z Remove the sparking plug lead.

z Take care not to grab running cutters.

1 Attention!

An unbalance can develop after regrinding of the blade.

z Always regrind the blades in a specialist workshop,

because an unbalance check should be undertaken

according to the safety regulations.

– Always change blades in a specialist workshop. A torque

spanner of 17 mm is mandatorily required.

Fastening torque of the screws: 38-42 N-m.

Adjusting the Bowden cable coupling

1. Raise the drive bracket (2) app. 2 cm and hold.

2. Loosen the locking nut (1).

3. Turn the setscrew (2) left until the drive wheels are blo-

cked when you pull the mower backwards.

4. Tighten locking nut (1).

Change oil only

z While engine is warm and fuel tank empty.

z Change oil after the first 5 working hours. There after change

engine oil every 25 working hours and at the end of the mo-

wing season. Change engine oil more frequently if working un-

der extreme and dusty conditions.

1. Remove oil filler cap.

2. Tilt machine slowly to side and allow oil to drain from the

crankcase through the filler.

3. Oil Fill .

Cleaning of Spark Plug

z Check and clean regularly

z Reset plug gap as required (0,76 mm).

Cleaning of air filter

Refer to the engine manufacturer‘s handbook supplied.

Storage in winter

z Drain the fuel tank.

z Drain the carburettor.

– This can be done by starting the engine and allowing it to

run until it stops of its own accord.

z Clean the mower thoroughly.

z Change the oil.

z Preserve the engine:

– Unscrew the sparking plug and pour one dessert spoon of

engine oil into the sparking plug opening

– Pull the starting cord slowly all the way (oil distribution in the

cylinder)

– Screw the sparking plug back in position (do not replace the

sparking plug lead)

z Store the mower in a cool and dry location.

z The mower should be checked by a WOLF customer service

workshop in the autumn.

Spare parts

M

P

Q

G

R

J

Ordering number Designation of the item Description of the item

4218 065 Grass catcher

4218 094 Vi 48 S Replacement blade 48 cm

2058 305 Champion RJ 19 LM Spark plug

2056 305 Air filter

4180 091 HD SAE 30 (VO 4T) Motor oil 0,6 l

17

G

Faults and how to remedy

Guarantee conditions

Please keep the guarantee card filled out by the vendor, or the re-

ceipt, in a safe place.

For a period of 24 months from the date of purchase, WOLF-Garten

provides a guarantee in accordance with the state of technology and

the application/area of usage. The legal rights of the end-user are not

affected by the following guarantee guidelines.

Pre-requisites for a 24-month guarantee claim:

- Only use the mower for private use.

If used commercially or for hire, the guarantee reduces to 12 months.

- Proper handling and observation of all notes in the operating in-

structions, which form part of the guarantee conditions.

- Keeping of the prescribed maintenance intervals.

- No modification to the design without approval.

- The use of original WOLF spare parts/accessories.

- Submission of the completed guarantee card and/or proof of

purchase.

The guarantee does not extend to the normal wear of cutters, cut-

ter fixing components such as friction discs, V-belts / toothed

belts, running wheels / tyres, air filters, sparking plugs and spar-

king plug connectors. In the event of a repair by yourself the gu-

arantee immediately becomes invalid in all respects.

Faults and defects whose cause can be attributed to material or

manufacturing faults are rectified exclusively by our official ser-

vice centres (the vendor has the right of repair) in your locality, or

by the manufacturer if that is closer. Demands in excess of the gu-

arantee are excluded. The possibility of a replacement unit does

not exist. Any transport damage should be reported not to us but

to the relevant transport organisation otherwise the right to a re-

placement may be lost.

Remedy (X) by

Problem Possible cause

WOLF

service-workshop

Yourself

Motor does not start or has

no power

• Insufficient fuel in the tank

--- X

• Spark plug lead not connected

--- X

• Spark plug out of order

--- X

• Air filter dirty or oily

--- X

• Blade fastening screw loose

X ---

Uneven cutting

• Incorrect cutting height

--- X

• Blunt blades

X ---

• Air / duct catcher bag blocked

--- X

Drive does not start • Clutch Bowden cable misadjusted

--- X

When in doubt, always consult a WOLF service workshop.

Important: switch off the mower and disconnect the spark plug lead before inspecting, cleaning or working on the blades.

The guarantee work is undertaken by our authorised customer

service workshops or by:

G

WOLFGarden Ltd.

Crown BusinessPark

Tredegar

Gwent, NP22 4EF

Tel. : ++ 44 / 14 95 30 66 00

Fax : ++ 44 / 14 95 30 33 44

E-mail: [email protected]

Page is loading ...

www.WOLF-Garten.com

Teil-Nr. 0054 552 - TB

Wolf Garten 2.48 A HW User manual

This manual is also suitable for

Wolf Garten 2.48 A HW User manual

in other languages

Related papers

Other documents