Cape Town - 9 Racecourse Road, Milnerton, 7441
Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065
www.eurolux.co.za
Please read instructions before commencing installation and retain for future reference.
ILLUSTRATIONS
50mm
200mm
0.5m
2
5
3
Before installation always ensure the power supply is turned off.
1. Cut a hole in the ceiling as per “cut out” make sure there are no beams or structures were you will be
cutting the holes.
2. Connect to electrical supply.
3. Hold both clips on either side of downlight upwards and insert downlight into ceiling hole ensuring the
mains lead is not trapped.
4. Pushttingupwardstosnaprmlyintoposition,ushwithceiling.
5. Insert the lamp by locating the pin connection holes within the lamp holder, gently pushing the lamp
into the holder and twisting into place.
6. Reconnect power.
NOTE:Alwaysallowthelamptocoolsufcientlybeforechanging.
NOTE: To avoid heat transfer from downlight, allow a minimum gap of about 200mm in height from
downlight to ceiling / any materials above the downlight and 50mm all around the sides of the downlight.
Failuretodosocouldresultinre.
INSTALLATION
CLEANING
•Beforecleaningalwaysensurethepowersupplyisturnedoff.
•Donotimmersetheluminaireinwater.
•Noabrasiveproducts,solvents,detergentmaybeusedtocleanthisluminaire.
•Ensurethatthettingdoesnotcomeincontactwithcorrosivechemicals,etc.
•Useasoftclothtoclean.
•Cut-out: Please refer to packaging for cut out measurement
SPECIFICATIONS
ATTACHMENTS:
Iftheexternalexiblecableorcordofthisluminaireisdamaged,itshouldbeexclusively
replacedbythemanufacturerorhisserviceagentorasimilarqualiedpersoninordertoavoidahazard.
To ensure that you get maximum longevity and maximum use out of your luminaire, please
observe the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire must be carried out
byaqualiedelectrician,inaccordancewithSANS10142.Oncompletionofinstallation,ensurethatthe
CerticateofComplianceisupdated.
• Beforeconnectingtheluminaire,ensurethatvoltageindicatedontheratinglabelcorrespondswiththemainsvoltage
in your home.
• Whenchangingthelamp,ensurethatthepoweristurnedoff.
• Ensurethatthecorrectlamptypeandwattageistted.
• Thisluminaireischeckedinfullforconformitytothequalitystandardsandsafetyrequirements.
• Themanufacturer/supplierisnotresponsibleforanydamageofpropertiesandpersons,causedbytheincorrectuse
or installation of the luminaire.
• Shouldyoubeunsureofhowtoinstallthisluminairecorrectly,pleaseconsultaprofessionalelectricianoryour
supplier for assistance.
• Ensureallitems/components,threadsandscrewsaretightlysecured.
IMPORTANT:
• Tamperingwiththisluminaire,I.E.Usingsiliconsealersorincorrectcabling,willinvalidateyourwarranty.
• Ifthereisaprotectiveglassinstalledandisdamaged,itshouldbereplacedimmediately.
• Pleasecheckwhethertheconnectionofthepowercordissafeandreliablebeforeinstallation.
• Ifyourmainswiringdiffersinanywayfromdiagram,consultaqualiedelectrician.
• Alwaysensurethatthemainssupplyvoltageiscorrect.
• Alwaysreplacethelampwithoneofanidenticalratingandwattage.
• Chokinghazard:Maycontainsmallparts.Keepawayfromchildren.
• Donotinsertyourngersoranypartofyourbodyintotheelectricalcontactandsocketsofthisproductwhilstitis
connected to the electrical supply.
• Itemmayvaryslightlyfromthepictureonthecarton.
• Coastalhumiditymayeffectthelongevityoftheluminaire.
IMPORTANTSAFEGUARDS
ENVIRONMENTAL PROTECTION
Wasteelectrical&Electronicequipmentregulationsrequiresthatanyofourproducts
showing this marking must not be disposed of with other household or commercial
waste. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate any such products from other waste
types and recycle it responsibly at your local facilities.