PRO POINT 8977084 User manual

Category
Welding System
Type
User manual

The PRO POINT 8977084 welding mask is perfect for protecting your eyes and face while welding. With a digital shade that ranges from 5 to 13, this mask automatically adjusts to the brightness of the welding arc, ensuring optimal protection. The grind mode allows you to switch to a clear lens for grinding tasks without removing the mask. The adjustable headband and silicone padding provide a comfortable and secure fit, while the replaceable inner and outer lenses ensure long-lasting durability.

The PRO POINT 8977084 welding mask is perfect for protecting your eyes and face while welding. With a digital shade that ranges from 5 to 13, this mask automatically adjusts to the brightness of the welding arc, ensuring optimal protection. The grind mode allows you to switch to a clear lens for grinding tasks without removing the mask. The adjustable headband and silicone padding provide a comfortable and secure fit, while the replaceable inner and outer lenses ensure long-lasting durability.

V1.0 8977084
Please read and understand all instructions before use. Retain this manual for future reference.
S
WELDING MASK KIT
TRUBLU LOPRO
8977084 TRUBLU LoPro Welding Mask Kit V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Viewing Area 4.33 x 1.57 in.
Lens Shade Digital 5 to 9 / 9 to 13
Reaction Time
0.1 to 0.9
Optical Classification 1/1/1/2
Headgear Adjustable ratcheting type
Grind Mode Yes
ADF Controls Digital
Number of Arc Sensors 2
Power Source Battery
Battery Type CR2450
Viewing Area 4.33 x 1.57 in.
Operating Temperature -10 to 65°C (14 to 149°F)
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual.
A notice is an alert that there is a possibility of property damage, injury
or death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice
that could result in severe personal injury or death if the
proper precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that
may result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe
practice will result in equipment or property damage, but
not personal injury.
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 3
INTRODUCTION
The TRUBLU LoPro Welding Mask provides 5 to 13 shade protection for
your eyes while the faceplate stops welding spatters and ultraviolet and
infrared radiation. The grind function can be activated or deactivated
without removing the goggles.
There is room under the welding mask to fit a standard half-welding
mask respirator. The faceplate can be removed.
SAFETY
WARNING! Read and understand all instructions before using this
tool. The operator must follow basic precautions to reduce the
risk of personal injury and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or
inspection and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean,
well-lit and free of distractions. Place lights so you are not working
in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away
from the work area.
3. Store tools properly in a safe and dry location. Keep tools out of
the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National
Standards Institute (ANSI).
1. Wear gloves that provide protection based on the work materials or
to reduce the effects of tool vibration.
2. Wear protective clothing designed for the work environment and
tool.
3. Control the tool, personal movement and the work environment to
avoid personal injury or damage to the tool.
4. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
8977084 TRUBLU LoPro Welding Mask Kit V1.0
4 For technical questions call 1-800-665-8685
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to the tool safety rules.
If you use this tool unsafely or incorrectly, you can suffer serious
personal injury.
WARNING! The welding mask does not protect against severe
impact hazards, explosions or corrosive liquids. Machine guards
or eye splash protection must be used when these hazards are
present.
WARNING! Using filter forms from any other manufacturer’s welding
mask can seriously impaired the protection provided and may result
in serious personal injury.
1. Use the correct tool for the job. This welding mask was designed for a
specific function. Do not modify or alter this welding mask or use it for
an unintended purpose.
2. Do not use the tool if any parts are damaged, broken or misplaced.
Repair or replace the parts.
3. This welding mask is not recommended for overhead welding
applications, laser welding or laser cutting applications.
4. In the event of electronic failure, the filter remains dark at Shade 15
to protect against UV and IR radiation.
5. Use the auto-darkening welding filter with inner and outer cover
lenses. Never open or tamper with the filter cartridge.
6. Ensure the front cover lens is mounted before use. Remove the
protective film.
7. Ensure that the lens is clean and there is no dirt or spatter covering
the four sensors at the front of the filter cartridge.
8. Inspect all parts for signs of wear or damage. Any scratched or
cracked parts should be replaced prior to use.
9. Never place the welding mask on a hot surface.
10. Arc rays can burn both eyes and skin. Arc welding produces
intense visible and invisible (ultraviolet and infrared) rays. Wear a
welding mask fitted with the proper shade to protect your face and
eyes when welding or watching.
11. Check whether welding or grinding mode is chosen before use.
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 5
12. The reaction of the filter’s liquid crystal will be slower if the ambient
temperature is low, but it will not affect protective functions.
13. Replace the protective lenses immediately if broken or scratched.
The damage will obscure vision and reduce the filter’s protective
performance.
14. The welding hood included in this kit is flame-retardant. This
welding hood does not provide protection against molten metals.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace
the missing part before operating. Failure to do so could result in
a malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for
damage.
IDENTIFICATION KEY
A Shell
B Outer Lens
C Auto Darkening Goggles
D Inner Lens
E Silicone Padding
F Plastic headband
G Elastic Headband
H Bag
I Welding Hood (May differ
from illustration)
J LED Light
DISPLAY ICONS
K Battery Status
L WELD Mode
M Shade 5-9
N Shade 9-13
O Sensitivity (1 to 5)
P Delay (1 to 5)
Q Shade Setting
R CUT Mode
S GRIND Mode
Fig.
1
Fig. 2
8977084 TRUBLU LoPro Welding Mask Kit V1.0
6 For technical questions call 1-800-665-8685
ASSEMBLY & INSTALLATION
Letter references in parenthesis (A) refer to the included Identification Key.
The welding mask is preassembled. Remove the protective film from both
lenses before use.
SWITCHING HEADBANDS
The welding mask has two headbands: plastic (F) and elastic (G).
Switch out the headbands by pushing on
the headbands lock catch until it pops
off. Repeat on the other side.
Push the lock catch against the locks on
each side of the goggles (Fig. 3) until
they snap into place.
ADJUST THE WELDING MASK FIT (PLASTIC
HEADBAND)
The headband should be adjusted both in diameter and height.
1. Adjust the headband diameter with the adjusting knob on the headband.
Twist clockwise to tighten and counterclockwise to loosen.
2. Adjust the headband height by releasing the segmental positioning
plate and changing the top strap hole.
ATTACH THE LED LIGHT
1. Place the light’s base in front of the face plate’s bracket.
2. Align the bracket’s tabs with the base’s slots.
3. Push the light backwards until it touches the bracket’s backstop.
4. Remove the light by pulling it forward until it is free of the bracket.
OPERATION
WARNING! Do not weld if the orange light inside the goggles is
flashing. This is the Grind mode indicator and you can suffer eye
or retina damage, as the lens will not darken when the welding
arc forms.
Fig. 3
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 7
BEFORE WELDING
1. Ensure that the internal and external protective films are removed from
the lenses.
2. Check that the batteries have sufficient power to operate the
welding mask.
3. Check that the arc sensors are clean and not blocked by dust or
debris.
4. Check for head band tightness before each use.
WELDING MASK SETTINGS
The control panel is on the left side of the googles, with the exception of
the GRIND button, which is on the right side of the goggles.
1. Press the MODE button to cycle through the four modes: Weld (5-9),
Weld (9-13), Grind and Cut. The icons and numbers shown on the
LCD screen depends on which mode is selected.
2. Once a mode is selected, press the SHADE, SENS. or DELAY
button once to activate that setting. The icon will begin flashing.
3. Continue to press the button to cycle through the setting levels.
4. The icon will stop flashing after a few seconds, indicating the
setting is complete.
SHADE NUMBER SELECTION
1. Determine what DIN Shade number is
needed for the task (see Appendix A).
2. Select to the weld mode that has the
correct range, either Shade 9-5 (M) or
9-13 (N). The weld icon (L) will also
be visible (Fig. 4).
3. Press the SHADE button once to
activate the setting and then press it
again until the correct shade number
(Q) is displayed. It will only cycle
through the number in the selected
range.
Fig. 4
8977084 TRUBLU LoPro Welding Mask Kit V1.0
8 For technical questions call 1-800-665-8685
DELAY TIME
Delay time refers to the time the cartridge filter is set to change from the
dark to bright state after welding stops. The delay can be adjusted up to
a 0.9 second delay.
A short delay is suitable for spot or short welds. This allows you to track
the progress of the weld. A long delay is better suited for heavy welding
when there is an afterglow.
1. Select the weld mode, then press the DELAY button until the delay
icon (P) flashes.
2. Each press of the DELAY button will add a bar to the delay time.
Each bar increases the delay by 0.2 seconds starting from 0.1 to
0.9 seconds.
SENSITIVITY
Sensitivity is the reaction time between the welding arc’s formation and
when the lens darkens.
Low Setting (0.1) Suitable for high amperage welding and welding
in areas with high levels of natural sunlight.
Medium Setting (0.5) Suitable for most indoors and outdoors welding.
High Setting (0.9) Suitable for low amperage welding and welding
in areas with low light conditions, especially for
low amperage argon-arc welding.
1. Select the weld mode, then press the SENS. button until the
sensitivity icon (O) flashes.
2. Each press of the SENS. button will add a bar to the sensitivity.
Each bar increases the sensitivity by 0.2 seconds starting from 0.1
to 0.9 seconds.
CUT MODE
WARNING! Do not use these goggles if the cutting task requires a
DIN shade higher than Shade 9. A bright cutting arc can cause
eye or retina damage if the Shade protection is inadequate.
1. Determine what DIN Shade number is
needed for the task.
2. Press the MODE button until the Cut
icon (R) appears in the LCD. The DIN
Shade 5-9 icon (M) will also appear.
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 9
3. Press the SHADE button until the icon (Q) is flashing. Press the
button to select the DIN shade.
GRINDING MODE
You can also use the welding mask to protect your face during grinding.
This will prevent the filter cartridge from darkening when bright sparks are
created.
1. Press the GRIND button on the right
side of the goggles for 2 seconds to
activate grind mode.
2. The grinding icon (S) will appear on
the LCD.
3. An orange light inside the goggles will flash when in grind mode.
You cannot adjust the shade number.
4. Press the GRIND button for 2 seconds to switch off GRIND mode.
BATTERY ICON
The battery icon (K) indicates the power charge available. Change the
batteries when down to a single bar that flashes (see Maintenance
Battery Replacement).
WARNING! Failure to change a low battery may result in exposure
to UV/IR radiation and blinding arc light. A low battery may
compromise the delay timing and shade accuracy.
SLEEP MODE
The welding mask will enter sleep mode after 30 minutes of inactivity to
conserve the battery power. Push any button to activate the goggles.
The last shade setting in weld mode will be retained in memory. Cut
and Grind settings are not saved to memory.
LED LIGHT
1. Push the power button on top to activate the light.
2. Loosen a side knob slightly.
3. Adjust the light to the desired position.
4. Tighten the side knob to secure.
5. Turn the power off until ready for use.
8977084 TRUBLU LoPro Welding Mask Kit V1.0
10 For technical questions call 1-800-665-8685
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient,
easier to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace
damaged or worn components. Only use identical replacement
parts when servicing.
3. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the
tool. An improperly repaired tool may present a hazard to the
user and/or others.
CHANGE EXTERNAL AND INTERNAL LENS
The external and internal lenses will wear out and need replacement
after a period of use due to exposure to the heat, fumes and particulate
matter generated during welding.
INTERNAL LENS
1. Grip the inner lens at the top (Fig. 8) at
the molded indent and pull it out. The
lens will flex and slide out of the side
hooks.
2. Position the new lens into the left hook
and push and bend the lens towards
you (Fig. 9).
3. Slip the right side of the lens under the
right hook and release the lens.
4. Gently push the lens into the goggles to
seat it in the opening.
EXTERNAL LENS
1. Grip the small tab on the bottom of the
outer lens (Fig. 10) and pull it out. The
lens will flex and slide out of the side
hooks.
Fig. 8
Fig. 9
Fig. 10
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 11
2. Position the new lens into the left hook by
aligning the lens tab with the hook
opening (Fig. 11).
3. Bend the lens towards yourself and slip the
right side of the lens under the right hook,
aligning the tab and release the lens.
4. Gently push the lens into the goggles to seat it in the opening.
REPLACE THE SILICONE PADDING.
The silicone padding is replaceable if it is torn or
damaged. The padding is held in place by tabs.
1. Pull the sides towards the middle to
disconnect the side tabs (Fig. 12).
2. Grip the padding by the upper left and right
corner and pull it from the goggle’s body.
3. Position the new padding onto the
goggle’s body. Gently press down on the
left and right side of the padding. Wiggle
the padding around until the side tabs
lock into place (Fig. 13).
4. Work your fingers around the inner edge
of the padding to force the tabs to lock
into place.
5. Gently pull along the padding edge to
check if it is secure. Repeat steps 3 and 4 if needed until the
padding is locked into place.
BATTERY REPLACEMENT
1. Remove the small cover
screw on the inner right
side of the goggles
(Fig. 13), then slide the
cover off the battery holder.
2. Remove the old battery and
replace with a new CR2450
lithium battery. Check that the battery’s polarity is correct.
3. Reinstall the cover.
Fig. 14
Fig. 11
Fig. 12
Fig. 13
8977084 TRUBLU LoPro Welding Mask Kit V1.0
12 For technical questions call 1-800-665-8685
REMOVING AND REINSTALLING THE
FACEPLATE
The faceplate is held in place by a lock and tab system on either side of
the goggles, just behind the control panel and grind button.
1. Press the left tab outward to free
it from the lock and hold it there.
2. At the same time, hold the onto
the faceplate and press against
the goggles on the same side.
The faceplate will pop off.
3. Repeat steps 1 and 2 on the
other side. Set the faceplate
aside once it is free.
4. Reattach the faceplate by aligning the locks and tabs on either side
of the goggles and faceplate.
5. Push the goggles down into place until the tabs catch onto the
locks. Check that the connection is firm on each side.
6. Clean the lenses of fingerprints after removing or installing the
mask.
CLEANING
Clean the lens, welding mask shell and headband with a soft cotton
cloth and mild soap. Replace the headband when required.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
Fig. 15
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 13
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not
function properly or parts are missing. If unable to do so, have a
qualified technician service the tool.
PROBLEM(S)
POSSIBLE CAUSE(S)
SUGGESTED SOLUTION(S)
Irregular
Darkening.
Headgear is set unevenly so
the distance between the eyes
and the lens is different from
the left to the right side.
Adjust headgear so distance
is equal between the lens and
both eyes.
Filter does not
darken or
flickers.
1. Front cover lens is dirty or
smoke covered.
2. Arc sensors may be dirty.
3. Welding current is too low.
4. Battery voltage is too low.
1. Clean or replace external
lens.
2. Remove external lens and
wipe the photo sensors
clean with soft lint free
cloth.
3. Adjust filter sensitivity to
the maximum.
4. Replace batteries.
Poor vision. 1. Check the clear covers
lenses and the electronic
filter lens for dirt or grime.
2. Protective film was not
removed.
3. Ambient light is not
sufficient to see.
4. Shade Number is not set
correctly.
1. Clean cover lenses and
electric filter lens.
2. Remove protective film.
3. Adjust the work area
lighting.
4. Reset Shade number.
Welding Cap
slips.
The headband is not properly
adjusted.
Adjust the headgear tightness
adjusting knob for a tighter fit.
8977084 TRUBLU LoPro Welding Mask Kit V1.0
14 For technical questions call 1-800-665-8685
APPENDIX A
V1.0 TRUBLU LoPro Welding Mask Kit 8977084
Visit www.princessauto.com for more information 15
8977084 TRUBLU LoPro Welding Mask Kit V1.0
16 For technical questions call 1-800-665-8685
V1,0 8977084
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil. Conservez ce
manuel afin de pouvoir le consulter plus tard.
TROUSSE POUR CASQUE
DE SOUDAGE
TRUBLU LOPRO
8977084 Trousse pour casque de soudage TRUBLU LoPro V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Zone de visibilité
4,33 x 1,57 po
Teinte de lentille
Numérique 5 à 9 / 9 à 13
Temps de réaction
0,1 à 0,9
Classification optique
1/1/1/2
Couvre-chef
Type à cliquet réglable
Mode de meulage
Oui
Commandes du filtre à
assombrissement automatique
Numérique
Nombre de capteurs d’arc
2
Source d’énergie
Pile
Type de batterie
CR2450
Zone de visibilité
4,33 x 1,57 po
Température de fonctionnement
-10 à 65 °C (14 à 149 °F)
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans
ce manuel. Un avis est une alerte indiquant qu'il existe un risque de
dommage à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque imdiat et particulier qui
entraînera des blessures corporelles graves ou
même la mort si on omet de prendre les précautions
nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement
dangereuse qui peut entraîner des blessures
mineures ou modérées si on ne procède pas de la
façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique
non sécuritaire qui entraînera des dommages au
niveau de l'équipement ou des biens, mais non des
blessures corporelles.
V1,0 Trousse pour casque de soudage TRUBLU LoPro 8977084
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
Le casque de soudage TRUBLU LoPro offre une protection de teintes 5
à 13, tandis que la visière protège contre les projections de soudure,
les rayons ultraviolets et le rayonnement infrarouge. La fonction de
meulage peut être activée ou désactivée sans retirer les lunettes de
sécurité.
Un espace prévu sous le casque de soudage permet de raccorder un
demi-masque respiratoire. La visière peut être retirée.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les
instructions avant d'utiliser cet outil. L'utilisateur doit respecter
les précautions de base lorsqu'il utilise cet outil afin de réduire
le risque de blessure ou de dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et
d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez
votre aire de travail propre, bien éclairée et exempte de toute
distraction. Placez les lampes de façon à ne pas travailler dans
l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec.
Gardez les outils hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
1. Portez des gants qui protègent en fonction des matériaux de travail
et pour réduire les effets des vibrations de l'outil.
2. Portez des vêtements de protection conçus pour l'environnement
de travail et pour l'outil.
8977084 Trousse pour casque de soudage TRUBLU LoPro V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
3. Gardez le contrôle de l'outil, de vos mouvements et de
l'environnement de travail pour éviter les blessures ou le bris de l'outil.
4. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT ! Ne permettez PAS au confort ou à votre
familiarisation avec l'outil (obtenus après un emploi répété) de
se substituer à une adhésion stricte aux règles de sécurité de
l'outil. Si vous utilisez cet outil de façon dangereuse ou
incorrecte, vous pouvez subir des blessures corporelles graves.
AVERTISSEMENT ! Le masque de soudeur à assombrissement
automatique ne protège pas contre les impacts élevés, les
explosions ou les liquides corrosifs. Utilisez un protecteur
sur l’appareil ou protégez-vous les yeux lorsque ces dangers
sont présents.
AVERTISSEMENT ! L’utilisation d’un filtre provenant du masque
d’un autre fabricant peut compromettre sérieusement la
protection offerte et entraîner des blessures graves.
1. Utilisez le bon masque de soudeur pour la tâche à effectuer. Cet
masque de soudeur a été conçu pour une utilisation spécifique. Évitez
de modifier ou d’altérer cet masque de soudeur ou de l’utiliser à une
fin autre que celle pour laquelle il a été conçu.
2. N’utilisez pas l’outil si des pièces psentent des dommages ou
sont déplacées. Réparez ou remplacez les pièces.
3. Le masque de soudeur à assombrissement automatique n’est pas
recommandé pour les opérations de soudage en hauteur, le
soudage au laser ou le découpage au laser.
4. En cas de panne électronique, le filtre demeure foncé afin de
protéger contre les rayons ultraviolets et infrarouges conformément
à la teinte 15.
5. Utilisez le filtre de soudage à assombrissement automatique avec
des couvre-lentilles internes et externes. N’ouvrez ni ne trafiquez
jamais la cartouche du filtre.
6. Assurez-vous que la lentille de couvercle avant est installée avant
de l’utiliser. Retirez la pellicule protectrice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

PRO POINT 8977084 User manual

Category
Welding System
Type
User manual

The PRO POINT 8977084 welding mask is perfect for protecting your eyes and face while welding. With a digital shade that ranges from 5 to 13, this mask automatically adjusts to the brightness of the welding arc, ensuring optimal protection. The grind mode allows you to switch to a clear lens for grinding tasks without removing the mask. The adjustable headband and silicone padding provide a comfortable and secure fit, while the replaceable inner and outer lenses ensure long-lasting durability.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages