George Kovacs P6983-077-L User manual

P6983-077-L
Brand
George Kovacs
Model
P6983-077-L
Type
User manual

This manual is also suitable for

The George Kovacs P6983-077-L is a dimmable LED wall mount fixture with a single light source and a stylish design that blends contemporary and classic elements. Its energy-efficient LED technology provides warm, inviting illumination while saving energy. The fixture is easy to install and maintain, with a simple mounting process and replaceable LED modules for long-lasting use. Its compatibility with various dimmer types, including C-L (CFL & LED) and Incandescent/Halogen dimmers, allows for customized lighting control and ambiance adjustment.

The George Kovacs P6983-077-L is a dimmable LED wall mount fixture with a single light source and a stylish design that blends contemporary and classic elements. Its energy-efficient LED technology provides warm, inviting illumination while saving energy. The fixture is easy to install and maintain, with a simple mounting process and replaceable LED modules for long-lasting use. Its compatibility with various dimmer types, including C-L (CFL & LED) and Incandescent/Halogen dimmers, allows for customized lighting control and ambiance adjustment.

`
IMPORTANT: Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with C-L (CFL & LED)type and
Incandescent/Halogen type dimmers
INSTALLATION INSTRUCTIONS FOR P6981/P6982/P6983/P6984-L
For LED Wall Mount Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AV E R T I S S E M E N T ! CO U P E R L E C O U R A N T AU N IV E A U D E S F U S I B L E S O U D O DI S J O NC T E U R .
PREPARATION
1. Shut off power at the circuit breaker and remove the old
fixture, including the mounting hardware.
2. Carefully remove the fixture from the carton and check that
all parts are included as shown in the illustration.
3. Position mounting plate (C) on the wall, and mark the
location of the two drywall anchors (D). Pre-drill the holes
for the drywall anchors (D). Insert the drywall anchors (D)
into the wall.
4. Attach the mounting plate (C) to the outlet box with
mounting screws (B) (Size:8-32*1/2’’L) and wood screws
(N). The side of the mounting plate marked “GND” must
face out.
CONNECTING THE WIRES
5. Connect the electrical wires as shown in Fig.2, making sure
that all wire nuts are secured. If your outlet has a ground wire
(green or bare copper), connect the fixture's ground Wire to
it. Otherwise, connect the fixture's ground wire directly to the
Mounting plate (C) using the green screw (A) provided.
FINISHING THE INSTALLATION (FIG. 1)
6. Align fixture (I) to mounting plate (C) and secure with screws
(J).
7. Hang crystal strands (H) to the holes on the frame (T). Place
the cage (L) onto the clips (G) and secure cage (L) to fixture
(I) with cap nuts (K).
CAUTION /ATTENTION : When handling the fixture, do not
apply pressure to the LEDs. Hold the fixture by the base or
front plate (I) only.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps
for more details (Fig 3.)
Warning: Turn off power at the circuit breaker before
replacing LED module or LED driver.
a. Remove cage (L) from fixture (I) and remove fixture (I) from
mounting plate (C).
b. Remove the wire nuts located inside the fixture (I) to
disconnect the LED module.
c. Remove screws (O) on cover (N) to remove the cover (N)
and acrylic shade (Q). Remove screws (S) to remove the
heat sink (M) from fixture (I).
d. Remove screws (R) and remove LED module (P) from heat
sink (M).
e. Reverse steps a-c for installing the new LED module.
f. Note: The LED module should be provided by a specified
supplier.
g. For better heat dissipation the LED module (Q) should be
applied with thermal grease when re-lamping.
Fig.1
Brand: Lutron
Ordering Information ■Boxed ●Clamshell
Model number
Control type
Maximum capacity
■DVCL-153P-
Single-pole/3-way
dimmer-
150 W CFL/LED or 600
W Incandescent/
Halogen 120 V
●DVCL-153PH-
■DVSCCL-153P-
■CTCL-153P-
●CTCL-153PH-
■AYCL-153P-
●AYCL153PH-
●TTCL-100H-
Single-pole lamp
dimmer
100W CFL/LED or 250W
Incandescent/ Halogen
120v
Fig 3
Fig.2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
  • Page 1 1

George Kovacs P6983-077-L User manual

P6983-077-L
Brand
George Kovacs
Model
P6983-077-L
Type
User manual
This manual is also suitable for

The George Kovacs P6983-077-L is a dimmable LED wall mount fixture with a single light source and a stylish design that blends contemporary and classic elements. Its energy-efficient LED technology provides warm, inviting illumination while saving energy. The fixture is easy to install and maintain, with a simple mounting process and replaceable LED modules for long-lasting use. Its compatibility with various dimmer types, including C-L (CFL & LED) and Incandescent/Halogen dimmers, allows for customized lighting control and ambiance adjustment.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents