Opel DVD 800 User manual

Contents

Introduction ................................ 1-1

Radio .......................................... 2-1

Audio player ............................... 3-1

Navigation .................................. 4-1

Mobile Phone Portal ................... 5-1

Index .......................................... 6-1

DVD800.book Page 1 Tuesday, August 26, 2008 1:51 PM

DVD800.book Page 2 Tuesday, August 26, 2008 1:51 PM

1 - 1Introduction

Introduction

General information

The Infotainment system DVD 800

provides you with state-of-the-art

in-car infotainment.

For the FM and AM wavebands the

radio is equipped with twelve

automatically assignable channel

presets. Furthermore, 36 channels

can be allocated manually

(waveband-independent).

Using RDS-TMC you also always

have the latest information on the

current traffic situation.

The integrated audio player will

entertain you with audio CDs and

MP3 CDs, as well as with MP3 DVDs.

Furthermore, you can connect

external data storage devices (e.g.

iPod, MP3 player or USB stick) or a

portable player to the Infotainment

system as further audio sources.

The digital sound processor provides

you with several preset equalizer

modes for sound optimisation.

The navigation system with dynamic

route planning will guide you reliably

to your destination, and if desired will

automatically avoid traffic jams or

other traffic problems.

Optionally, the Infotainment system

can be operated using a steering

wheel remote control and a

multifunction unit between the front

seats.

In addition the Infotainment system

can be equipped with a mobile phone

portal.

The well thought-out design of the

control elements, the clear displays

and a large multifunction knob enable

you to control the system easily and

intuitively.

Introduction ......................... 1-1

Overview............................. 1-5

Operation ............................ 1-10

DVD800.book Page 1 Tuesday, August 26, 2008 1:51 PM

1 - 2 Introduction

Use the Infotainment

instructions

 You can gain a quick overview of

the many functions of the

Infotainment system complete with

an overview of all the control

elements in the section "Overview".

 You will find a description of the

basic control steps of the

Infotainment system in the section

"Operation".

 You can find your way around

using the list of contents at the

beginning of the operating

instructions and in the individual

sections.

 You can find your way around by

way of the alphabetical index.

 You will find detailed function

descriptions of your Infotainment

system in the individual sections.

 Directions such as left, right, front

or rear are always relative to the

direction of travel.

Important information about

the content of these

instructions

Depending on the model variant,

country variant, integrated special

equipment and accessories, the

scope of equipment of your vehicle

can differ from the descriptions in

these operating instructions.

Special notations

Page references are marked with 3.

The 3 means "refer to page".

Display screens

Some on-screen displays depend on

the unit settings and on the vehicle

equipment and can therefore vary.

9 Danger, 9 Warning,

Caution

9 Danger

Texts that are marked 9 Danger

indicate a possible danger to life.

Non-compliance with the

instructions can cause danger to

life.

9 Warning

Texts marked 9 Warning indicate

possible dangers of accident and

injury. Non-compliance with the

instructions can cause injury.

Caution

Texts marked Caution indicate

possible damage to the vehicle.

Non-compliance with the

instructions can cause damage to

the vehicle.

DVD800.book Page 2 Tuesday, August 26, 2008 1:51 PM

1 - 3Introduction

Important information for

operation and traffic safety

Theft protection

The Infotainment system is equipped

with an electronic security system for

the purpose of theft protection.

The Infotainment system therefore

functions only in your vehicle and is

worthless for a thief.

9 Warning

The usage of the navigation

system does not release the driver

from the responsibility for a correct,

vigilant attitude in road traffic. The

related traffic regulations must

always be followed.

The Infotainment system has to be

used so that the vehicle can be

steered safely at all times. If in

doubt stop your vehicle and

operate the Infotainment system

while the vehicle is stationary.

9 Warning

Only make entries (e.g. addresses)

with the vehicle stationary.

If a navigation instruction should

contradict traffic regulations, the

traffic regulations always apply.

In some areas one-way streets and

other roads and entrances (e.g.

pedestrian zones) that you are not

allowed to turn into are not marked

on the map. In such areas the

Infotainment system will issue a

warning that must be accepted.

Here you must pay particular

attention to one-way streets, roads

and entrances that you are not

allowed to drive into.

DVD800.book Page 3 Tuesday, August 26, 2008 1:51 PM

1 - 4 Introduction

DVD800.book Page 4 Tuesday, August 26, 2008 1:51 PM

1 - 5Introduction

Overview

Control elements

1 RADIO (Band).......................2-1

Activate radio or

change waveband

2 CD/AUX ................................3-1

Start CD/MP3 replay

or change audio source

3 Search backward

Radio: search backward .......2-1

CD/MP3:

skip track backward ..............3-2

4 NAV.......................................4-3

Press once:

Display map

Press twice:

Navigation menu

5 Search forward

Radio: search forward...........2-1

CD/MP3: skip track forward ..3-2

6 Knob ................................1-10

Press: switch on/off

Infotainment system

Turn: adjust volume

7 Station buttons 1 ..6 ..............2-1

Long press: save station

Short press: select station

8 CONFIG ..............................1-15

System settings

9 TP .........................................2-5

Activate or deactivate

radio traffic service

0 TONE ..................................1-15

Tone settings

a AS (1/2) .................................2-1

Automatic memory levels

Short press:

select autostore list

Long press:

save station automatically

b INFO

Additional, situation-dependent

information

c FAV (1/2/3)............................2-1

Favourite lists

d CD/DVD ejection

e Multifunction knob ...............1-11

Central control for

selection and navigation

in menus

f Eight-way switch ...................4-9

Navigation:

move display window

in map view

g CD/DVD slot

h RPT (NAV) ..........................4-23

Repeat last navigation

message

i BACK ..................................1-11

Menu: one level back

Input: delete last character or

entire entry

j DEST.....................................4-4

Navigation destination entry

k PHONE

Open telephone menu...........5-3

Activate mute ......................1-10

DVD800.book Page 5 Tuesday, August 26, 2008 1:51 PM

1 - 6 Introduction

DVD800.book Page 6 Tuesday, August 26, 2008 1:51 PM

1 - 7Introduction

Steering wheel remote

control

1 Take call..............................5-10

Activate voice control ..........5-11

2 End call ...............................5-10

Activate mute ......................5-10

3 SRC (Source)

Press:

Select audio source

Turn upwards: next

preset radio station

or next CD/MP3 title

Turn downwards: previous

preset radio station

or previous CD/MP3 title

4 Increase volume

5 Reduce volume

DVD800.book Page 7 Tuesday, August 26, 2008 1:51 PM

1 - 8 Introduction

DVD800.book Page 8 Tuesday, August 26, 2008 1:51 PM

1 - 9Introduction

Multifunction unit

1 NAV.......................................4-3

Press once:

Display map

Press twice:

Navigation menu

2 AUDIO

Change audio source

3 Take/end call.......................5-10

Activate

or deactivate mute

4 DEST ....................................4-4

Navigation destination entry

5 BACK

Menu: one level back

Input: delete last character or

entire entry

6 Multifunction knob ...............1-11

Central control for selection

and navigation in menus

7 Eight-way switch ...................4-9

Navigation:

move display window

in map view

DVD800.book Page 9 Tuesday, August 26, 2008 1:51 PM

1 - 10 Introduction

Operation

Control elements

The Infotainment system is operated

via function buttons, multifunction

knobs and menus that are shown on

the display.

Inputs are made optionally via:

 the central control unit in the

instrument panel 3 1-5

 the steering wheel remote control

3 1-7

 the multifunction unit between the

front seats 3 1-9

Switching the Infotainment

system on or off

Press the knob briefly. After

switching on the Infotainment source

last selected is active.

Automatic switch-off

If the Infotainment system has been

switched on by means of the knob

when the ignition was switched off,

it will switch off again automatically

30 minutes after the last user input.

Setting the volume

Turn knob. The current setting is

shown on the display.

When the infotainment system is

switched on, the volume last selected

is set.

If necessary, the volume is limited to

the factory-set maximum switch on

volume.

The following can be set separately:

 the volume of the traffic

announcements 3 1-15

 the volume of the navigation

messages 3 4-23

DVD800.book Page 10 Tuesday, August 26, 2008 1:51 PM

1 - 11Introduction

Speed compensated volume

When speed compensated volume is

activated 3 1-15 the volume is

adapted automatically pro rata to the

vehicle speed to compensate for

engine and tyre noise.

Mute

Press the PHONE button for a few

seconds to switch the audio sources

to mute.

To cancel mute again: turn the

knob or press the PHONE button for

a few seconds again.

Function areas

Radio

Press the RADIO button to open the

radio main menu or to change

between the different wavebands.

Press the multifunction knob to open

a submenu with options for station

selection.

Detailed description of the radio

functions 3 2-1.

Audio player

Press CD/AUX button to open the

CD, USB, iPod

®

or AUX menu

(if available) or to change between

these menus.

Press the multifunction knob to open

a submenu with options for track

selection.

Detailed description of the audio

player functions 3 3-1.

Navigation

Press NAV button twice to open the

Navigation menu.

Detailed description of the navigation

system functions 3 4-1.

Mobile phone portal

Press the PHONE button to open the

telephone menu.

Press the multifunction knob to open

a submenu with options for the input

or selection of numbers.

Detailed description of the mobile

phone portal functions 3 5-1.

Handling the menus

Multifunction knob

The multifunction knob is the central

control element for the menus.

Turn

 To mark a menu option

 To set a numeric value

Press (the outer ring)

 To select or activate the marked

option

 To confirm a set value

 To switch a system function on/off

DVD800.book Page 11 Tuesday, August 26, 2008 1:51 PM

1 - 12 Introduction

BACK button

Press the button briefly to:

 exit a menu,

 return from a submenu to the next

higher menu level,

 delete the last character in a

character sequence.

Press the button for a few seconds to

delete the entire entry

Examples of menu operation

Selecting an option

Turn the multifunction knob to move

the cursor (= coloured background) to

the desired option.

Press the multifunction knob to select

the marked option.

Submenus

An arrow on the right-hand edge of

the menu indicates that after

selection of the option a submenu

with further options will be opened.

Activating a setting

Turn the multifunction knob to mark

the desired setting.

Press the multifunction knob to

activate the setting.

Setting a value

Turn the multifunction knob to change

the current value of the setting.

Press the multifunction knob to

confirm the set value.

DVD800.book Page 12 Tuesday, August 26, 2008 1:51 PM

1 - 13Introduction

Switching a function on or off

Turn the multifunction knob to mark

the function to be switched on or off.

Press the multifunction knob to switch

between the settings On and Off.

Entering a character sequence

To enter character sequences,

e.g. telephone numbers or road

names:

Turn the multifunction knob to select

the desired character.

Press the multifunction knob to

confirm the selected character.

By means of the BACK button the

last character in the character

sequence can be deleted. A long

press deletes the entire entry.

Tone settings

In the tone settings menu the tone

characteristic can be set differently

for each radio waveband and each

audio player source.

Press the TONE button to open the

tone menu.

DVD800.book Page 13 Tuesday, August 26, 2008 1:51 PM

1 - 14 Introduction

Setting bass, middle and treble

Select Bass, Middle or Treble.

Set the desired value for the option

selected.

Setting the volume distribution

between front - rear

Select Fader.

Set the desired value.

Setting the volume distribution

between right - left

Select Balance.

Set the desired value.

Setting individual setting to "0"

Select the desired option and press

the multifunction knob for a few

seconds.

Setting all settings to "0" or

"Off"

Press TONE button for a few

seconds.

DVD800.book Page 14 Tuesday, August 26, 2008 1:51 PM

1 - 15Introduction

Optimising the tone for the

style of music

Select EQ (Equalizer).

The displayed options offer optimised

bass, middle and treble presettings

for the relevant style of music.

Select required option.

System settings

Diverse settings and adaptations for

the Infotainment system can be

performed at any time.

Press the CONFIG button to open the

system settings menu.

Volume settings

Speed compensated volume

Select Radio settings and then

Speed dependent volume.

Speed compensated volume can be

deactivated or the degree of volume

adaptation can be selected in the

menu displayed.

Select required option.

Volume of the traffic

announcements (TA)

The volume of the traffic

announcements can be increased or

reduced in comparison to the normal

audio volume.

Select Radio settings, RDS options

and TA volume one after the other.

Set the desired value.

DVD800.book Page 15 Tuesday, August 26, 2008 1:51 PM

1 - 16 Introduction

Setting the time and date

If the displays for time or date have to

be altered:

Select Time & Date.

Selectable setting options:

 Set time: Changes the time shown

on the display.

 Set date: Changes the date shown

on the display (with Infotainment

system switched off).

 Set time format: Changes

indication of hours between

12 hours and 24 hours.

 Set date format: Changes

indication of date between

MM/DD/YYYY and DD.MM.YYYY.

 Display digital clock: Switches

on/off indication of time on the

display.

 RDS clock synchronization: After

switching on this function the time

display is constantly updated

automatically via the time signal of

an RDS channel 3 2-6. RDS time

synchronisation can take a few

minutes.

Make the desired settings.

Selecting display mode

Select Display settings.

Selectable display settings:

 Day mode: Optimisation of the

display for daylight conditions.

 Night mode: Optimisation of the

display for darkness.

 Automatic mode: The display

changes mode when the vehicle

lights are switched on/off.

Select required option.

Changing the language

DVD800.book Page 16 Tuesday, August 26, 2008 1:51 PM

1 - 17Introduction

In case the language of the menu

displays, the navigation messages

and the voice output of the mobile

phone portal have to be changed:

Select Vehicle settings and then

Languages.

Select desired language.

DVD800.book Page 17 Tuesday, August 26, 2008 1:51 PM

2 - 1 Radio

Radio

Operation

Control buttons

The most important buttons for

control of the radio are as follows:

 RADIO: Activate radio

 , : Station search

 AS: Autostore lists

 FAV: Favourite lists

 1 ..6: Preset buttons

 TP: Radio traffic service

Activating the radio

Press the RADIO button to open the

radio main menu.

The station last played will be

received.

Selecting the waveband

Press the RADIO button to switch

between the AM and FM wavebands.

The last station received in the

waveband is played (if it can be

received).

Selecting station

Automatic station search

Briefly press the button or .

A search is made for the next station

that can be received and it is played

automatically.

A search can be made for all the

stations in the current waveband in

succession in this manner.

If the radio does not find a station, it

switches automatically to a more

sensitive search level. If it still does

not find a station, the frequency that

was last active is set again.

Operation............................. 2-1

RDS..................................... 2-6

DVD800.book Page 1 Tuesday, August 26, 2008 1:51 PM

Page is loading ...

Opel DVD 800 User manual

Opel DVD 800 User manual

Related papers

Other documents