DFI KS057R-FS User manual

Type
User manual

This manual is also suitable for

DFI KS057R-FS is a versatile system that can be used in various applications. It features a Mini PCIe slot, enabling you to expand its functionality by adding a wireless module or other compatible cards. The DIN-rail mount allows for easy installation in industrial settings, while the wall mount option provides flexibility for different mounting scenarios. Communication capabilities include RS485 and RS232 ports, ensuring compatibility with a wide range of devices. Additionally, the USB 2.0 and USB 3.0 ports allow for convenient data transfer and peripheral connectivity.

DFI KS057R-FS is a versatile system that can be used in various applications. It features a Mini PCIe slot, enabling you to expand its functionality by adding a wireless module or other compatible cards. The DIN-rail mount allows for easy installation in industrial settings, while the wall mount option provides flexibility for different mounting scenarios. Communication capabilities include RS485 and RS232 ports, ensuring compatibility with a wide range of devices. Additionally, the USB 2.0 and USB 3.0 ports allow for convenient data transfer and peripheral connectivity.

1
Package Contents
One
KS057R-FS System Unit
Wall Mount Bracket/Screw Pack
• DIN-rail Bracket/Screw Pack
Panel
Side View
DFI reserves the right to change the specications at any time prior to the product's release. For the latest revision and details of the
installation process, please refer to the user's manual.
www.d.com
Antenna hole
KS057R-FS Installation Guide
Connector Panel
Antenna hole
LAN 2 LAN 1
(GbE) (GbE)
Grounding
Status LED
(green)
HDMI
USB 2.0
DC-in
Reset
COM (RS232)
COM (RS485)
2
4. Lift the cover to open the system. The Mini PCIe socket is readily accessible
after removing the top cover.
Removing the Chassis Cover
Please observe the following guidelines and follow the procedure to open
the system.
1. Make sure the system and all other peripheral devices connected to it have
been powered off.
2. Disconnect all power cords and cables.
3. The 4 mounting screws attached touchscreen cover and the 6 screws on the
sides of the system are used to secure the touch panel to the chassis. Remove
these screws and put them in a safe place for later use. Be careful when open-
ing the touch panel to avoid pulling the connecting cables apart.
Mounting screw
Mounting screw
3
Installing a Mini PCIe Card
Note:
If installing a wireless module, place the antenna cable(s) on top of the Mini PCIe and route
the cables to the side of the chassis to reach the antenna holes.
The system board is equipped with 1 full-size Mini PCIe slot that supports both
PCIe and USB signals.
1. Grasp the Mini PCIe card by its edges and align the notch of the card with the
key in the connector on the system board.
2. Push down on the other end of the Mini PCIe card and use the provided mount-
ing screw to secure the card on the system board.
Mounting screw
Mini PCIe socket
Micro SD slot
(on the back side)
Antenna hole
4
DIN-rail Mount
The system features DIN-rail mount chassis that facilitates fast installation of the
KS057R-FS to a DIN rail.
The DIN-rail mount kit includes the following:
• DIN-rail mount brackets
• 4 screws
1. Use the provided mounting screws to attach the DIN-rail mount brackets to the
rear side of the device. Note that the connector panel should be at the bottom.
2. Install the device onto the rail.
Mounting screws
Din-rail mount bracket
5
Wall Mount
The system also features wall mount chassis that enables you to mount the device
on the wall.
The wall mount kit includes the following:
• Wall mount brackets
• 4 screws
1. Use the provided mounting screws to attach wall mount brackets to both sides
of the device.
2. Fix the device on the wall. The following picture shows the dimension and lo-
cation of wall mount screw holes.
170.20
121.00
186.00
95.80
170.20
121.00
186.00
95.80
6
The system is equipped with one 2-pole terminal block that enables RS485 com-
munication on the connector panel.
Communication Port Pin Assignments
COM (RS485)
RS485 Pin Assignments
Pin 1 (starting at the left)
RS485-
Pin 2 RS485+
6
7
8
9
1
2 3 4
5
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
The system is also equipped with one DB9 serial port that enables RS232 commu-
nication on the connector panel.
COM (RS232)
7
Board Layout and Jumper Settings
Boot Mode Select SW5
Boot from the fuses 7 Off, 8 Off
Serial downloader 7 On, 8 Off
Boot from the board settings (default) 7 Off, 8 On
Reserved 7 On, 8 On
www.d.com
Panel Backlight/SATA Power
5
1
DC-in
USB 1-2
USB 2.0
1
10
9
2
JTAG
Mini
PCIe
Battery
1
1
9
DIODebug
1
4
DDR3L
DDR3L
Debug LED
1
5
2
USB 3
USB 2.0
USB OTG
COM 1
HDMI
LAN 2
LAN 1
Front
Panel
COM 3
1
microSD
eMMC
1 5
NXP
i.MX6
Cortex-A9
Boot Mode/Device Select
(SW5)
ON
1 2 3 4 5 6 7 8
5 9
I C
2
1
LVDS LCD Panel
1
14
DDR3L
DDR3L
Top
Bottom
Boot
Device
Select
SW5
1 2 3 4 5 6 7 8
eMMC (default) On On Off Off On On Off On
SPI xx xx xx On On Off Off On
SD On Off On Off Off On Off On
Note:
SW5 switch is located on the back side of the system board. It is for development and
troubleshooting which should only be performed by developers and service technicians who
are fully aware of the outcome of any changes to the settings.
8
Board Layout and Internal Connectors
A-540-Q-2020
JTAG
Pin Pin Name Pin Pin Name
1
3.3V
2
JTAG _TMS
3
GND
4
JTAG_TCK
5
GND
6
JTAG_TDO
7
JTAG_MOD
8
JTAG_TDI
9
JTAG_nTRST
10
JTAG_nRESET
Pin Pin Name
1
3.3V
2
UART5_RX
3
UART5_TX
4
GND
1
Debug Connector
Pin Pin Name
1
GPIO7
2
GPIO6
3
GPIO5
4
GPIO4
5
GPIO3
6
GPIO2
7
GPIO1
8
GPIO0
9
3.3V
10
GND
DIO Connector
Pin Pin Name
1
5V
2
Data-
3
Data+
4
GND
5
NC
USB 2.0 Connector (USB 3)
1 2
5
The USB OTG connector allows the
system to read and write to the onboard
eMMC memory from your host computer
by using a micro-B type USB cable. Your
system is pre-loaded with Yocto 1.8 beta
or Android 5.1 beta on the eMMC.
USB 2.0 Connector (USB 3)
1
2
9
10
1
2
9
10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

DFI KS057R-FS User manual

Type
User manual
This manual is also suitable for

DFI KS057R-FS is a versatile system that can be used in various applications. It features a Mini PCIe slot, enabling you to expand its functionality by adding a wireless module or other compatible cards. The DIN-rail mount allows for easy installation in industrial settings, while the wall mount option provides flexibility for different mounting scenarios. Communication capabilities include RS485 and RS232 ports, ensuring compatibility with a wide range of devices. Additionally, the USB 2.0 and USB 3.0 ports allow for convenient data transfer and peripheral connectivity.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI