Channel Vision C-0317 User manual
- Category
- Cable splitters or combiners
- Type
- User manual
CVT-15WB
C-0317
15dB Amplifier for Standard & Wide-Band
CATV Systems
0
1
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWEROUT+POWER
CHANNEL VISION
TM
CVT-15WB
CATV For ward Path (54-860MHz ):+15dB
CATV Ret urn Path (5-42MHz): Pa ssive
WideBan d CATV Path (975-1525 MHz):Pa ssive
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POW EROUT+POW ER
CHANNEL VISION
TM
CVT-15WB
CATV For ward Path ( 54-860M Hz):+15dB
CATV Ret urn Path (5 -42MHz) : Passive
WideBan d CATV Pat h (975-15 25MHz):Passi ve
TM
CHANNEL VISION
Central
DC 12V
INPUT
CABLE/ANT.
INPUT
CATV FORWARD PATH (54-860MHz): +15dB
CATV RETURN PATH (5-42MHz): PASSIVE
WIDEBAND CATV PATH (975-1525MHz): PASSIVE
OUT+POWER
C-0317
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POW EROUT+POW ER
CHANNEL VISION
TM
CVT-15WB
CATV For ward Path ( 54-860M Hz):+15dB
CATV Ret urn Path (5 -42MHz) : Passive
WideBan d CATV Pat h (975-15 25MHz):Passi ve
TM
CHANNEL VISION
Central
DC 12V
INPUT
CABLE/ANT.
INPUT
CATV FORWARD PATH (54-860MHz): +15dB
CATV RETURN PATH (5-42MHz): PASSIVE
WIDEBAND CATV PATH (975-1525MHz): PASSIVE
OUT+POWER
C-0317
IN
6-WAY SPLITTER 5MHz-1GHz
All ports DC passing
TM
C HA NN EL V I SI ON
Part No. HS-6
OUT OUT OUT
OUT OUT OUT
2
3
The CVT-15WB and C-0317 are 15dB Amplifiers for standard and
advanced digital CATV systems. The wide bandwidth design allows 2-way
communications in the RF spectrum from 975-1525MHz which is required
by some newer digital cable boxes. The CVT-15WB is idea for surface
mount applications while the C-0317 is designed to easily snap into a
structured wire enclosure.
Features:
!
15dB Amplifier
!
Passive return path from 5-42MHz
!
Compatible with Advanced Wide-Bandwidth Digital CATV systems
!
Built-in 6KV surge protection for superior durability
!
Phantom powered using model CVT-PI
!
Easy installation
!
CVT-15WB Dimensions: 4.70” x 4.35” x 1.06”
!
C-0317 Dimensions: 6.38” x 4.35” x 1.30”
Accessories Included:
Power Supply
TV OUTPUTS
Connect TVs here
CVT-15WB C-0317
POWER IN
Connect power supply here
12VDC, 500mA
CABLE IN
Connect the antenna or cable service feed here
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POW ERO UT+PO WER
CHANNEL VISION
TM
CVT-15WB
CATV For ward Path ( 54-86 0MHz):+ 15dB
CATV Ret urn Path (5 -42MH z): Passi ve
WideBan d CATV Pat h (975- 1525MHz ):Passi ve
HS-2 ... 2-way RF splitter for cable TV and
antenna signals.
HS-3 ... 3-way RF splitter for cable TV and
antenna signals.
HS-4 ... 4-way RF splitter for cable TV and
antenna signals.
HS-6 ... 6-way RF splitter for cable TV and
antenna signals.
2120 ... 75ohm RF terminator. Use to
terminate unused outputs of splitters.
Accessories & Complementary Products (sold separately)
RF distribution systems require splitters and other accessories to deliver
the amplified signals to the TV.
HS-8 ... 8-way RF splitter for cable TV and
antenna signals.
Part No. HS-3
3-WAY SPLITTER/COMBINER
5MHz-1GHz All Ports DC passing
TM
C H AN N EL V I SI O N
IN
/out
OUT/in OUT/in OUT/in
TM
C H A N N E L VISION
8-WAY SPLITTER 5MHz-1GHz
All ports DC passing
Part No. HS-8
IN
OUT OUTOUT OUT
OUT OUTOUT OUT
Part No. HS-2
2-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
C HA NN EL V IS IO N
IN
/out
OUT/inOUT/in
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CHA NN EL VIS ION
IN
/outOUT/in OUT/in
OUT/inOUT/in
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POW EROUT+POW ER
CHANNEL VISION
TM
CVT-15WB
CATV For ward Path ( 54-860MHz):+ 15dB
CATV Ret urn Path (5 -42MHz): Passi ve
WideBan d CATV Pat h (975-15 25MHz):Passi ve
TM
CHANNEL VISION
Central
DC 12V
INPUT
CABLE/ANT.
INPUT
CATV FORWARD PATH (54-860MHz): +15dB
CATV RETURN PATH (5-42MHz): PASSIVE
WIDEBAND CATV PATH (975-1525MHz): PASSIVE
OUT+POWER
C-0317
IN
6-WAY SPLITTER 5MHz-1GHz
All ports DC passing
TM
C HA NN EL V I SI ON
Part No. HS-6
OUT OUT OUT
OUT OUT OUT
2
3
The CVT-15WB and C-0317 are 15dB Amplifiers for standard and
advanced digital CATV systems. The wide bandwidth design allows 2-way
communications in the RF spectrum from 975-1525MHz which is required
by some newer digital cable boxes. The CVT-15WB is idea for surface
mount applications while the C-0317 is designed to easily snap into a
structured wire enclosure.
Features:
!
15dB Amplifier
!
Passive return path from 5-42MHz
!
Compatible with Advanced Wide-Bandwidth Digital CATV systems
!
Built-in 6KV surge protection for superior durability
!
Phantom powered using model CVT-PI
!
Easy installation
!
CVT-15WB Dimensions: 4.70” x 4.35” x 1.06”
!
C-0317 Dimensions: 6.38” x 4.35” x 1.30”
Accessories Included:
Power Supply
TV OUTPUTS
Connect TVs here
CVT-15WB C-0317
POWER IN
Connect power supply here
12VDC, 500mA
CABLE IN
Connect the antenna or cable service feed here
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POW ERO UT+PO WER
CHANNEL VISION
TM
CVT-15WB
CATV For ward Path ( 54-86 0MHz):+ 15dB
CATV Ret urn Path (5 -42MH z): Passi ve
WideBan d CATV Pat h (975- 1525MHz ):Passive
HS-2 ... 2-way RF splitter for cable TV and
antenna signals.
HS-3 ... 3-way RF splitter for cable TV and
antenna signals.
HS-4 ... 4-way RF splitter for cable TV and
antenna signals.
HS-6 ... 6-way RF splitter for cable TV and
antenna signals.
2120 ... 75ohm RF terminator. Use to
terminate unused outputs of splitters.
Accessories & Complementary Products (sold separately)
RF distribution systems require splitters and other accessories to deliver
the amplified signals to the TV.
HS-8 ... 8-way RF splitter for cable TV and
antenna signals.
Part No. HS-3
3-WAY SPLITTER/COMBINER
5MHz-1GHz All Ports DC passing
TM
C H AN N EL V I SI O N
IN
/out
OUT/in OUT/in OUT/in
TM
C H A N N E L VISION
8-WAY SPLITTER 5MHz-1GHz
All ports DC passing
Part No. HS-8
IN
OUT OUTOUT OUT
OUT OUTOUT OUT
Part No. HS-2
2-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
C HA NN EL V IS IO N
IN
/out
OUT/inOUT/in
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CHA NN EL VIS ION
IN
/outOUT/in OUT/in
OUT/inOUT/in
Basic Amplified Splitter Application
Connect the CVT-15WB (or C-0317) as shown and locate it at the main
distribution point in the house. The CVT-15WB will supply the amplified TV
signal to the splitter which may be connected to several TV locations.
CVT-15WB
Input from
Antenna or CATV
Power
Supply
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWEROUT+POWER
CHANNEL VISION
TM
CVT-15WB
CATV Forwa rd Path (54-860 MHz):+15dB
CATV Retur n Path (5-42MHz ): Passive
WideBand CATV Path (975-1 525MHz):Passi ve
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CH A N N EL V ISION
IN
/outOUT/in OUT/in
OUT/inOUT/in
TV set
TV set
TV set
TV set
4
5
Part No. HS-2
2-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
C H AN N E L V I SI O N
IN
/out
OUT/inOUT/in
Basic RF System Design
Knowing how much amplification is needed for a system is essential to
designing a successful RF distribution system. This section explains how to
calculate the losses in your system. You should provide enough amplification
to overcome all of the insertion losses of all the system components. If the
signal splits into two branches, each branch must be calculated separately.
~5.0dB
3.5dB
5.5dB
7.5dB
9.0dB
15.5dB
11.0dB
HS-2 (2-way Splitter)
HS-3 (3-way Splitter)
HS-4 (4-way Splitter)
HS-6 (6-way Splitter)
HS-8 (8-way Splitter)
HS-16 (16-way Splitter)
100ft. of RG6
System Component
Typical Insertion Loss
CVT-15WB
Antenna
or CATV
+10dBmV
+25dBmV
+21.5dBmV +21.5dBmV
Insertion Loss:
-3.5dB
Insertion Loss: -9dB
Insertion
Loss:
-7.5dB
Gain:
+15dB
+14.5dBmV
+11.5dBmV
Example: Assume a CATV input
signal of 10dBmV. Next, calculate
all the gains and losses of the
components.
Primary Branch Calculation:
CATV Input: 10dBmV
CVT-15WB: +15dB
HS-2: -3.5dB
Main total: +21.5dBmV
4-Way Branch:
Main: +21.5dBmV
HS-4: -7.5dB
+14.5dB
6-Way Branch:
Main: +21.5dBmV
HS-6: -9.0dB
+11.5dB
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWE ROUT+POWE R
CHANNEL VISION
TM
CVT-15WB
CATV F orward Path (54-86 0MH z): +15 dB
CATV R eturn Path (5-42MH z): P ass ive
WideBand C ATV Path (975- 152 5MH z): Pas sive
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CHAN N EL VISI ON
IN
/outOUT/in OUT/in
OUT/inOUT/in
IN
6-WAY SPLITTER 5MHz-1GHz
All ports DC passing
TM
C H AN N EL V I SI O N
Part No. HS-6
OUT OUT OUT
OUT OUT OUT
Basic Amplified Splitter Application
Connect the CVT-15WB (or C-0317) as shown and locate it at the main
distribution point in the house. The CVT-15WB will supply the amplified TV
signal to the splitter which may be connected to several TV locations.
CVT-15WB
Input from
Antenna or CATV
Power
Supply
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWEROUT+POWER
CHANNEL VISION
TM
CVT-15WB
CATV Forwa rd Path (54-860 MHz):+15dB
CATV Retur n Path (5-42MHz ): Passive
WideBand CATV Path (975-1 525MHz):Passi ve
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CH A N N EL V ISION
IN
/outOUT/in OUT/in
OUT/inOUT/in
TV set
TV set
TV set
TV set
4
5
Part No. HS-2
2-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
C H AN N E L V I SI O N
IN
/out
OUT/inOUT/in
Basic RF System Design
Knowing how much amplification is needed for a system is essential to
designing a successful RF distribution system. This section explains how to
calculate the losses in your system. You should provide enough amplification
to overcome all of the insertion losses of all the system components. If the
signal splits into two branches, each branch must be calculated separately.
~5.0dB
3.5dB
5.5dB
7.5dB
9.0dB
15.5dB
11.0dB
HS-2 (2-way Splitter)
HS-3 (3-way Splitter)
HS-4 (4-way Splitter)
HS-6 (6-way Splitter)
HS-8 (8-way Splitter)
HS-16 (16-way Splitter)
100ft. of RG6
System Component
Typical Insertion Loss
CVT-15WB
Antenna
or CATV
+10dBmV
+25dBmV
+21.5dBmV +21.5dBmV
Insertion Loss:
-3.5dB
Insertion Loss: -9dB
Insertion
Loss:
-7.5dB
Gain:
+15dB
+14.5dBmV
+11.5dBmV
Example: Assume a CATV input
signal of 10dBmV. Next, calculate
all the gains and losses of the
components.
Primary Branch Calculation:
CATV Input: 10dBmV
CVT-15WB: +15dB
HS-2: -3.5dB
Main total: +21.5dBmV
4-Way Branch:
Main: +21.5dBmV
HS-4: -7.5dB
+14.5dB
6-Way Branch:
Main: +21.5dBmV
HS-6: -9.0dB
+11.5dB
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWE ROUT+POWE R
CHANNEL VISION
TM
CVT-15WB
CATV F orward Path (54-86 0MH z): +15 dB
CATV R eturn Path (5-42MH z): P ass ive
WideBand C ATV Path (975- 152 5MH z): Pas siv e
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CHAN N EL VISI ON
IN
/outOUT/in OUT/in
OUT/inOUT/in
IN
6-WAY SPLITTER 5MHz-1GHz
All ports DC passing
TM
C H AN N EL V I SI O N
Part No. HS-6
OUT OUT OUT
OUT OUT OUT
6
7
Specifications: (typical @25º C)
Specifications subject to change without notice.
Part No. HS-2
2-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
C H AN N E L V I SI O N
IN
/out
OUT/inOUT/in
Basic RF System Design
Knowing how much amplification is needed for a system is essential to
designing a successful RF distribution system. This section explains how to
calculate the losses in your system. You should provide enough amplification
to overcome all of the insertion losses of all the system components. If the
signal splits into two branches, each branch must be calculated separately.
~5.0dB
3.5dB
5.5dB
7.5dB
9.0dB
15.5dB
11.0dB
HS-2 (2-way Splitter)
HS-3 (3-way Splitter)
HS-4 (4-way Splitter)
HS-6 (6-way Splitter)
HS-8 (8-way Splitter)
HS-16 (16-way Splitter)
100ft. of RG6
System Component
Typical Insertion Loss
CVT-15WB
Antenna
or CATV
+10dBmV
+25dBmV
+21.5dBmV +21.5dBmV
+14.5dBmV
+11.5dBmV
Example: Assume a CATV input
signal of 10dBmV. Next, calculate
all the gains and losses of the
components.
Primary Branch Calculation:
CATV Input: 10dBmV
CVT-15WB: +15dB
HS-2: -3.5dB
Main total: +21.5dBmV
4-Way Branch:
Main: +21.5dBmV
HS-4: -7.5dB
+14.5dB
6-Way Branch:
Main: +21.5dBmV
HS-6: -9.0dB
+11.5dB
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWE ROUT+POWE R
CHANNEL VISION
TM
CVT-15WB
CATV F orward Path (54-86 0MH z): +15 dB
CATV R eturn Path (5-42MH z): P ass ive
WideBand C ATV Path (975- 152 5MH z): Pas sive
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CHAN N EL VISI ON
IN
/outOUT/in OUT/in
OUT/inOUT/in
IN
6-WAY SPLITTER 5MHz-1GHz
All ports DC passing
TM
C H AN N EL V I SI O N
Part No. HS-6
OUT OUT OUT
OUT OUT OUT
Frequency Range
54-1525MHz
5-42 + 975-1525MHz
Gain
54-60MHz
5-42MHz
60-860MHz
975-1000MHz
1000-1525MHz
(Passive) 975-1525MHz
+14.0dB
-3.0dB
-4.0dB
+14.0dB
-5.0dB
-3.5dB
+15.0dB
-2.0dB
-2.5dB
+15.5dB
-4.0dB
-2.5dB
+16.0dB
-1.0dB
+1.0dB
+1.0dB
-1.5dB
>15dB
>15dB
>110dB
75 ohm
12-15VDC
+16.0dB
-3.0dB
-1.5dB
Return Loss (I/O)
Return Loss (I/O)
Nominal Impedance “F” Female
Supply Voltage (DC)
3.0dB
60ns
12ns
60dBC
70dBC
+23.0dBmV
150mA
60dBC
60dBC
22ns
Noise Figure@70 degrees F
Group Delay (54 to 66MHz)
Group Delay (66 to 88MHz)
Group Delay (88 to 1000MHz)
Composite Second Order Distortions
Composite Triple Beat Distortions
Cross Modulation Distortions
Second Hum Modulation
Rated Output Level @160 channels, 6MHz each
Power Consumption
Flatness
Flatness
RFI Shielding
ITEM MIN. MAX.TYP.
CATV FORWARD PATH
CATV RETURN PATH
GENERAL SPEC
6
7
Specifications: (typical @25º C)
Specifications subject to change without notice.
Part No. HS-2
2-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
C H AN N E L V I SI O N
IN
/out
OUT/inOUT/in
Basic RF System Design
Knowing how much amplification is needed for a system is essential to
designing a successful RF distribution system. This section explains how to
calculate the losses in your system. You should provide enough amplification
to overcome all of the insertion losses of all the system components. If the
signal splits into two branches, each branch must be calculated separately.
~5.0dB
3.5dB
5.5dB
7.5dB
9.0dB
15.5dB
11.0dB
HS-2 (2-way Splitter)
HS-3 (3-way Splitter)
HS-4 (4-way Splitter)
HS-6 (6-way Splitter)
HS-8 (8-way Splitter)
HS-16 (16-way Splitter)
100ft. of RG6
System Component
Typical Insertion Loss
CVT-15WB
Antenna
or CATV
+10dBmV
+25dBmV
+21.5dBmV +21.5dBmV
+14.5dBmV
+11.5dBmV
Example: Assume a CATV input
signal of 10dBmV. Next, calculate
all the gains and losses of the
components.
Primary Branch Calculation:
CATV Input: 10dBmV
CVT-15WB: +15dB
HS-2: -3.5dB
Main total: +21.5dBmV
4-Way Branch:
Main: +21.5dBmV
HS-4: -7.5dB
+14.5dB
6-Way Branch:
Main: +21.5dBmV
HS-6: -9.0dB
+11.5dB
DC12V
INPUT
DC12V
INPUT
RF INPUTRF INPUT
OUT+POWE ROUT+POWE R
CHANNEL VISION
TM
CVT-15WB
CATV F orward Path (54-86 0MH z): +15 dB
CATV R eturn Path (5-42MH z): P ass ive
WideBand C ATV Path (975- 152 5MH z): Pas siv e
Part No. HS-4
4-WAY SPLITTER/COMBINER
5MHz-1GHz All Port DC passing
TM
CHAN N EL VISI ON
IN
/outOUT/in OUT/in
OUT/inOUT/in
IN
6-WAY SPLITTER 5MHz-1GHz
All ports DC passing
TM
C H AN N EL V I SI O N
Part No. HS-6
OUT OUT OUT
OUT OUT OUT
Frequency Range
54-1525MHz
5-42 + 975-1525MHz
Gain
54-60MHz
5-42MHz
60-860MHz
975-1000MHz
1000-1525MHz
(Passive) 975-1525MHz
+14.0dB
-3.0dB
-4.0dB
+14.0dB
-5.0dB
-3.5dB
+15.0dB
-2.0dB
-2.5dB
+15.5dB
-4.0dB
-2.5dB
+16.0dB
-1.0dB
+1.0dB
+1.0dB
-1.5dB
>15dB
>15dB
>110dB
75 ohm
12-15VDC
+16.0dB
-3.0dB
-1.5dB
Return Loss (I/O)
Return Loss (I/O)
Nominal Impedance “F” Female
Supply Voltage (DC)
3.0dB
60ns
12ns
60dBC
70dBC
+23.0dBmV
150mA
60dBC
60dBC
22ns
Noise Figure@70 degrees F
Group Delay (54 to 66MHz)
Group Delay (66 to 88MHz)
Group Delay (88 to 1000MHz)
Composite Second Order Distortions
Composite Triple Beat Distortions
Cross Modulation Distortions
Second Hum Modulation
Rated Output Level @160 channels, 6MHz each
Power Consumption
Flatness
Flatness
RFI Shielding
ITEM MIN. MAX.TYP.
CATV FORWARD PATH
CATV RETURN PATH
GENERAL SPEC
500-253 rev B1
www.chann e l v i s i o n . c o m
234 Fischer Avenue, Costa Mesa, California 92626 USA
(714)424-6500 (800)840-0288 (714)424-6510 fax
email: [email protected]
Channel Vision Technology will repair or replace any defect in
material or workmanship which occurs during normal use of this
product with new or rebuilt parts, free of charge in the USA, for one
year from the date of original purchase. This is a no hassle warranty
with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied
by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only
to the original purchaser, and a purchase receipt, invoice, or other
proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be
obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
Channel Vision products are not intended for use in medical,
lifesaving, life sustaining or critical environment applications.
Channel Vision customers using or selling Channel Vision products
for use in such applications do so at their own risk and agree to fully
indemnify Channel Vision for any damages resulting from such
improper use or sale.
1
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Channel Vision C-0317 User manual
- Category
- Cable splitters or combiners
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Channel Vision CVT-15WB User manual
-
Channel Vision C-0216 User manual
-
-
-
-
-
-
-
-
Other documents
-
CableWholesale 201-202 Datasheet
-
WisyCom CSI16T User manual
-
-
MuxLab CATV Balun II User guide
-
Channel Plus DA-506BID User manual
-
-
MuxLab CATV Distribution Hub Installation guide
-
Leviton 47693-ESM User manual
-
Wi3 WiPMR Installation guide
-
Fracarro 283938 Datasheet
